Roadwarrior
This scenario shows different ways to setup a roadwarrior VPN connection; in which, instead of using a N2N (network to network) connection, a single machine (e.g., a host) is able to connect to a remote private network.
On the one hand, DUT2 and DUT0 represent a remote branch
office. On the other hand, DUT1 is a roadwarrior that can
establish a connection to DUT2 using different virtual IPs.
Note that security associations (SAs) have to be manually
flushed with the command clear vpn ipsec sa. Depending on
the configuration parameter connection-type, the new tunnel
connections will be created or not.
Test VPN Roadwarrior Connection With VTI
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 address 10.3.0.1/24 set protocols static route 10.1.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.374 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.374/0.374/0.374/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.304 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.304/0.304/0.304/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.508 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.508/0.508/0.508/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::d4d7:f5ff:fe62:88f2/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.341 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.341/0.341/0.341/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.969 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.969/0.969/0.969/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 31b34767ae5cbf5f_i bbf5f065154c020a_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 15861s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3351s, expires in 3959s in c38dfd84 (0x90000000), 168 bytes, 2 packets, 1s ago out c1492bef (0x90000000), 168 bytes, 2 packets, 1s ago local 10.1.0.0/24 remote 0.0.0.0/0
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100% Closed tunnels: 1
Step 12: Set the following configuration in DUT1:
del interfaces dum0 set interfaces dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::d4d7:f5ff:fe62:88f2/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=8.11 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 8.108/8.108/8.108/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.620 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.620/0.620/0.620/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, 466b792ba95eb087_i ecb2add15993625b_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 14533s peer-PEER-tunnel-VTI: #2, reqid 2, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3448s, expires in 3959s in c942139a (0x90000000), 168 bytes, 2 packets, 0s ago out cc938d27 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Test VPN Roadwarrior Connection With Global Policies
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24 set protocols static route 10.3.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 address 10.3.0.1/24 set protocols static route 10.1.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.341 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.341/0.341/0.341/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.325 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.325/0.325/0.325/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.538 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.538/0.538/0.538/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::a0e9:76ff:fee1:117a/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.775 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.775/0.775/0.775/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.663 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.663/0.663/0.663/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 4863e09f3e63bd5a_i 20e440c993594538_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 16685s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3249s, expires in 3959s in c6aac428, 168 bytes, 2 packets, 1s ago out cd4c5287, 168 bytes, 2 packets, 1s ago local 10.1.0.0/24 remote 10.3.0.0/24
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100% Closed tunnels: 1
Step 12: Set the following configuration in DUT1:
del interfaces dum0 set interfaces dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::a0e9:76ff:fee1:117a/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.725 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.725/0.725/0.725/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.658 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.658/0.658/0.658/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, 2adae0c623f457dc_i 7cda0c3df680cf8e_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 16408s peer-PEER-tunnel-1: #2, reqid 2, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3531s, expires in 3960s in cc9a975f, 168 bytes, 2 packets, 0s ago out cee0a931, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test VPN Roadwarrior Connection With VTI And VIPs Pool
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set system vrf main set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.279 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.279/0.279/0.279/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.311 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.311/0.311/0.311/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.622 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.622/0.622/0.622/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
---------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ---------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::28a5:dff:fefa:b14c/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.417 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.417/0.417/0.417/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.747 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.747/0.747/0.747/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 65dafed864556f8a_i b99d586d40e60650_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 23280s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3257s, expires in 3959s in c093f544 (0x90000000), 168 bytes, 2 packets, 0s ago out cf1184c3 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32
Test VPN Roadwarrior Connection With Global Policies And VIPs Pool
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set system vrf main set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.328 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.328/0.328/0.328/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.458 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.458/0.458/0.458/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.634 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.634/0.634/0.634/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
---------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ---------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::cc2b:c1ff:fe68:b04/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.493 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.493/0.493/0.493/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.805 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.805/0.805/0.805/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 3e365909b49c088b_i a99780a2bafe338a_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 2s ago, rekeying in 27814s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 2s ago, rekeying in 3405s, expires in 3958s in c048dcae (0x90000000), 168 bytes, 2 packets, 0s ago out c2cb4332 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32