Roadwarrior
This scenario shows different ways to setup a roadwarrior VPN connection; in which, instead of using a N2N (network to network) connection, a single machine (e.g., a host) is able to connect to a remote private network.
On the one hand, DUT2 and DUT0 represent a remote branch
office. On the other hand, DUT1 is a roadwarrior that can
establish a connection to DUT2 using different virtual IPs.
Note that security associations (SAs) have to be manually
flushed with the command clear vpn ipsec sa. Depending on
the configuration parameter connection-type, the new tunnel
connections will be created or not.
Test VPN Roadwarrior Connection With VTI
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 address 10.3.0.1/24 set protocols static route 10.1.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.405 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.405/0.405/0.405/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.354 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.354/0.354/0.354/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.421 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.421/0.421/0.421/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::80f1:3aff:fe15:ea47/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.510 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.510/0.510/0.510/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.901 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.901/0.901/0.901/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 9ad2a1c89af0e40a_i d9e438309118f056_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 19613s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3341s, expires in 3959s in ceb43e74 (0x90000000), 168 bytes, 2 packets, 0s ago out c9cb3819 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100% Closed tunnels: 1
Step 12: Set the following configuration in DUT1:
del interfaces dum0 set interfaces dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::80f1:3aff:fe15:ea47/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.457 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.457/0.457/0.457/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.764 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.764/0.764/0.764/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, dd5bd87a87fb111f_i 3f7394eb4b3ce31b_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 22626s peer-PEER-tunnel-VTI: #2, reqid 2, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3314s, expires in 3960s in c7688b8a (0x90000000), 168 bytes, 2 packets, 0s ago out cddb4ee4 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Test VPN Roadwarrior Connection With Global Policies
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24 set protocols static route 10.3.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 address 10.3.0.1/24 set protocols static route 10.1.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.911 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.911/0.911/0.911/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.327 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.327/0.327/0.327/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.655 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.655/0.655/0.655/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::e4be:59ff:fe89:fa37/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.416 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.416/0.416/0.416/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.761 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.761/0.761/0.761/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 79ebe84756a4d1de_i dcf65633e8c39d34_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 25574s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3299s, expires in 3959s in ce23d67f, 168 bytes, 2 packets, 0s ago out cd73045c, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100% Closed tunnels: 1
Step 12: Set the following configuration in DUT1:
del interfaces dum0 set interfaces dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::e4be:59ff:fe89:fa37/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.473 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.473/0.473/0.473/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.679 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.679/0.679/0.679/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, ab1d39eb8aefdbc0_i f16d610f128a99eb_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 24575s peer-PEER-tunnel-1: #2, reqid 2, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3533s, expires in 3959s in c5a676a0, 168 bytes, 2 packets, 0s ago out ca387876, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test VPN Roadwarrior Connection With VTI And VIPs Pool
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set system vrf main set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.355 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.355/0.355/0.355/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.380 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.380/0.380/0.380/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.744 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.744/0.744/0.744/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::5c06:58ff:fee3:9e22/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.429 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.429/0.429/0.429/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.746 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.746/0.746/0.746/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, f13a71b0f8f1e017_i 2d2839727d53f6ab_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 16287s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3311s, expires in 3959s in cf5975fd (0x90000000), 168 bytes, 2 packets, 0s ago out c8f325a3 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32
Test VPN Roadwarrior Connection With Global Policies And VIPs Pool
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set system vrf main set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.376 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.376/0.376/0.376/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.397 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.397/0.397/0.397/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.489 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.489/0.489/0.489/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
---------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ---------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::64c2:4ff:feef:cfdf/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.451 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.451/0.451/0.451/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.775 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.775/0.775/0.775/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 328ac7e3dd23dbc9_i effd85188c93cf00_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 21432s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3262s, expires in 3959s in c4d427d5 (0x90000000), 168 bytes, 2 packets, 0s ago out c5c8cf76 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32