Roadwarrior
This scenario shows different ways to setup a roadwarrior VPN connection; in which, instead of using a N2N (network to network) connection, a single machine (e.g., a host) is able to connect to a remote private network.
On the one hand, DUT2 and DUT0 represent a remote branch
office. On the other hand, DUT1 is a roadwarrior that can
establish a connection to DUT2 using different virtual IPs.
Note that security associations (SAs) have to be manually
flushed with the command clear vpn ipsec sa. Depending on
the configuration parameter connection-type, the new tunnel
connections will be created or not.
Test VPN Roadwarrior Connection With VTI
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 address 10.3.0.1/24 set protocols static route 10.1.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.378 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.378/0.378/0.378/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.403 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.403/0.403/0.403/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.525 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.525/0.525/0.525/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::f808:4cff:fe7c:1e20/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.604 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.604/0.604/0.604/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=1.09 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.087/1.087/1.087/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, b774a68c4ea45c34_i c3f9ead30e187576_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 20695s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3326s, expires in 3959s in ce9ebeba (0x90000000), 168 bytes, 2 packets, 0s ago out c21a63c2 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100% Closed tunnels: 1
Step 12: Set the following configuration in DUT1:
del interfaces dum0 set interfaces dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::f808:4cff:fe7c:1e20/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.576 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.576/0.576/0.576/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=1.00 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.004/1.004/1.004/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, fb3727a39b074043_i 8018c359b02c66e7_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 27052s peer-PEER-tunnel-VTI: #2, reqid 2, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3345s, expires in 3960s in c55305d6 (0x90000000), 168 bytes, 2 packets, 0s ago out c911c765 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Test VPN Roadwarrior Connection With Global Policies
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24 set protocols static route 10.3.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 address 10.3.0.1/24 set protocols static route 10.1.0.0/24 interface eth0 set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.461 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.461/0.461/0.461/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.357 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.357/0.357/0.357/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.691 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.691/0.691/0.691/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::64a5:98ff:fe12:8b3b/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.410 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.410/0.410/0.410/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.708 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.708/0.708/0.708/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 9ccc477a70439107_i fb47d1009081ede8_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 24525s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3353s, expires in 3959s in c3b83850, 168 bytes, 2 packets, 0s ago out cb3c80f3, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100% Closed tunnels: 1
Step 12: Set the following configuration in DUT1:
del interfaces dum0 set interfaces dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::64a5:98ff:fe12:8b3b/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.456 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.456/0.456/0.456/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=1.07 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.071/1.071/1.071/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, 1b858dbb3b9046b7_i 3eb97e7ae42ecfd4_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 15133s peer-PEER-tunnel-1: #2, reqid 2, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3296s, expires in 3960s in cc6cb0fb, 168 bytes, 2 packets, 0s ago out c3d0a129, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test VPN Roadwarrior Connection With VTI And VIPs Pool
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set system vrf main set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.460 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.460/0.460/0.460/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.450 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.450/0.450/0.450/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.927 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.927/0.927/0.927/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::2477:4bff:fe3c:405a/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.546 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.546/0.546/0.546/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=1.05 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.045/1.045/1.045/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, be538e11ac360d78_i 97e3feacefc2b36d_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 20749s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3323s, expires in 3960s in ccfe13a2 (0x90000000), 168 bytes, 2 packets, 0s ago out c5e48cfe (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32
Test VPN Roadwarrior Connection With Global Policies And VIPs Pool
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2:
set interfaces eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1
Step 2: Set the following configuration in DUT0:
set interfaces eth0 address 80.0.0.1/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set interfaces eth1 address 10.1.0.1/24 set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local-prefix 10.1.0.0/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec esp-group CHILD-SA mode tunnel
Step 3: Set the following configuration in DUT1:
set interfaces eth0 address 80.0.0.2/24 set vpn ipsec auth-profile AUTH-SA local auth pre-shared-secret test set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec logging log-types any log-level 1 set interfaces dum0 set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set system vrf main set vpn ipsec esp-group CHILD-SA mode tunnel
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.332 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.332/0.332/0.332/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.419 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.419/0.419/0.419/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.390 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.390/0.390/0.390/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::185c:11ff:fe85:e9ed/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.512 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.512/0.512/0.512/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=1.03 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.027/1.027/1.027/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, d90ef1e921f5f096_i 39e0eb8d32dc7483_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 28388s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3389s, expires in 3959s in c9cbd3ca (0x90000000), 168 bytes, 2 packets, 0s ago out c01260b4 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32