Bonding
These scenarios cover some aspects related to link-aggregation, which is the technique of combining multiple network connections in parallel in order to increase throughput, to provide redundancy or both. On OSDx, this can be achieved by using bonding interfaces.
Test Round-Robin Mode
Description
A bonding interface is configured in DUT0 using the round-robin mode. This mode can be used to achieve load-balancing.
Scenario
Step 1: Set the following configuration in DUT0:
set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 address 192.168.100.10/24 set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set interfaces bonding bond0 mode round-robin
Step 2: Set the following configuration in DUT1:
set interfaces ethernet eth0 address 192.168.100.20/24
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c11/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: load balancing (round-robin)Show output
Ethernet Channel Bonding Driver: v5.10.127 Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:11 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:10 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 2 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.778 ms 64 bytes from 192.168.100.20: icmp_seq=2 ttl=64 time=0.365 ms --- 192.168.100.20 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 5ms rtt min/avg/max/mdev = 0.365/0.571/0.778/0.207 ms
Step 6: Run command interfaces ethernet clear at DUT0.
Step 7: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 58288 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 47.5 MBytes 399 Mbits/sec 11 197 KBytes [ 5] 1.00-2.00 sec 32.9 MBytes 276 Mbits/sec 3 147 KBytes [ 5] 2.00-3.00 sec 36.8 MBytes 309 Mbits/sec 29 238 KBytes [ 5] 3.00-4.00 sec 51.7 MBytes 434 Mbits/sec 31 242 KBytes [ 5] 4.00-5.00 sec 136 MBytes 1.14 Gbits/sec 135 365 KBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 305 MBytes 512 Mbits/sec 209 sender [ 5] 0.00-5.00 sec 303 MBytes 509 Mbits/sec receiver iperf Done.
Step 8: Run command interfaces ethernet show counters at DUT0 and check if output matches the following regular expressions:
eth0\s+up\s+\d+\s+\d+\s+0\s+\d{2,} eth1\s+up\s+\d+\s+\d+\s+0\s+\d{2,}Show output
----------------------------------------------------------------------------- Name Oper Rx Packets Rx Bytes Rx Errors Tx Packets Tx Bytes Tx Errors ----------------------------------------------------------------------------- eth0 up 19695 1473304 0 109921 166398903 0 eth1 up 22853 1720216 0 110489 167254632 0
Test Active-Backup Mode
Description
A bonding interface is configured in DUT0 using the active-backup mode. This mode can be used to achieve a higher degree of fault-tolerance.
Scenario
Step 1: Set the following configuration in DUT0:
set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 address 192.168.100.10/24 set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set interfaces bonding bond0 mode active-backup
Step 2: Set the following configuration in DUT1:
set interfaces ethernet eth0 address 192.168.100.20/24
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c11/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: fault-tolerance (active-backup)Show output
Ethernet Channel Bonding Driver: v5.10.127 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:11 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:10 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 2 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.496 ms 64 bytes from 192.168.100.20: icmp_seq=2 ttl=64 time=0.417 ms --- 192.168.100.20 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 14ms rtt min/avg/max/mdev = 0.417/0.456/0.496/0.044 ms
Step 6: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 42580 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 44.1 MBytes 370 Mbits/sec 1 971 KBytes [ 5] 1.00-2.00 sec 57.5 MBytes 482 Mbits/sec 0 2.20 MBytes [ 5] 2.00-3.00 sec 165 MBytes 1.38 Gbits/sec 0 3.13 MBytes [ 5] 3.00-4.00 sec 179 MBytes 1.50 Gbits/sec 0 3.13 MBytes [ 5] 4.00-5.00 sec 184 MBytes 1.54 Gbits/sec 0 3.13 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 629 MBytes 1.06 Gbits/sec 1 sender [ 5] 0.00-5.00 sec 629 MBytes 1.06 Gbits/sec receiver iperf Done.
Step 7: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth0Show output
Ethernet Channel Bonding Driver: v5.10.127 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:11 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:10 Slave queue ID: 0
Step 8: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 42598 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 167 MBytes 1.40 Gbits/sec 0 3.05 MBytes [ 5] 1.00-2.00 sec 171 MBytes 1.43 Gbits/sec 0 3.05 MBytes [ 5] 2.00-3.00 sec 184 MBytes 1.55 Gbits/sec 0 3.05 MBytes [ 5] 3.00-4.00 sec 179 MBytes 1.50 Gbits/sec 0 3.05 MBytes [ 5] 4.00-5.00 sec 156 MBytes 1.31 Gbits/sec 353 2.13 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 857 MBytes 1.44 Gbits/sec 353 sender [ 5] 0.00-5.00 sec 856 MBytes 1.43 Gbits/sec receiver iperf Done.
Step 9: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth1Show output
Ethernet Channel Bonding Driver: v5.10.127 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:11 Slave queue ID: 0 Slave Interface: eth0 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:10 Slave queue ID: 0