Bonding
These scenarios cover some aspects related to link-aggregation, which is the technique of combining multiple network connections in parallel in order to increase throughput, to provide redundancy or both. On OSDx, this can be achieved by using bonding interfaces.
Test Round-Robin Mode
Description
A bonding interface is configured in DUT0 using the round-robin mode. This mode can be used to achieve load-balancing.
Scenario
Step 1: Set the following configuration in DUT0:
set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 address 192.168.100.10/24 set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set interfaces bonding bond0 mode round-robin
Step 2: Set the following configuration in DUT1:
set interfaces ethernet eth0 address 192.168.100.20/24
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c10/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: load balancing (round-robin)Show output
Ethernet Channel Bonding Driver: v5.10.127 Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:10 Slave queue ID: 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:11 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 2 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.655 ms 64 bytes from 192.168.100.20: icmp_seq=2 ttl=64 time=0.438 ms --- 192.168.100.20 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 2ms rtt min/avg/max/mdev = 0.438/0.546/0.655/0.110 ms
Step 6: Run command interfaces ethernet clear at DUT0.
Step 7: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 46098 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 53.4 MBytes 448 Mbits/sec 9 160 KBytes [ 5] 1.00-2.00 sec 58.0 MBytes 487 Mbits/sec 65 296 KBytes [ 5] 2.00-3.00 sec 66.3 MBytes 556 Mbits/sec 36 344 KBytes [ 5] 3.00-4.00 sec 129 MBytes 1.08 Gbits/sec 213 335 KBytes [ 5] 4.00-5.00 sec 168 MBytes 1.41 Gbits/sec 111 386 KBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 475 MBytes 797 Mbits/sec 434 sender [ 5] 0.00-5.00 sec 474 MBytes 795 Mbits/sec receiver iperf Done.
Step 8: Run command interfaces ethernet show counters at DUT0 and check if output matches the following regular expressions:
eth0\s+up\s+\d+\s+\d+\s+0\s+\d{2,} eth1\s+up\s+\d+\s+\d+\s+0\s+\d{2,}Show output
----------------------------------------------------------------------------- Name Oper Rx Packets Rx Bytes Rx Errors Tx Packets Tx Bytes Tx Errors ----------------------------------------------------------------------------- eth0 up 40691 3087492 0 171949 260244069 0 eth1 up 43030 3269761 0 172108 260489727 0
Test Active-Backup Mode
Description
A bonding interface is configured in DUT0 using the active-backup mode. This mode can be used to achieve a higher degree of fault-tolerance.
Scenario
Step 1: Set the following configuration in DUT0:
set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 address 192.168.100.10/24 set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set interfaces bonding bond0 mode active-backup
Step 2: Set the following configuration in DUT1:
set interfaces ethernet eth0 address 192.168.100.20/24
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c10/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: fault-tolerance (active-backup)Show output
Ethernet Channel Bonding Driver: v5.10.127 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:10 Slave queue ID: 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:11 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 2 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.409 ms 64 bytes from 192.168.100.20: icmp_seq=2 ttl=64 time=0.337 ms --- 192.168.100.20 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 15ms rtt min/avg/max/mdev = 0.337/0.373/0.409/0.036 ms
Step 6: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 41380 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 84.0 MBytes 703 Mbits/sec 0 2.22 MBytes [ 5] 1.00-2.00 sec 166 MBytes 1.39 Gbits/sec 0 3.05 MBytes [ 5] 2.00-3.00 sec 170 MBytes 1.43 Gbits/sec 0 3.05 MBytes [ 5] 3.00-4.00 sec 175 MBytes 1.47 Gbits/sec 0 3.05 MBytes [ 5] 4.00-5.00 sec 195 MBytes 1.63 Gbits/sec 0 3.05 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 790 MBytes 1.32 Gbits/sec 0 sender [ 5] 0.00-5.01 sec 790 MBytes 1.32 Gbits/sec receiver iperf Done.
Step 7: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth0Show output
Ethernet Channel Bonding Driver: v5.10.127 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:10 Slave queue ID: 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:11 Slave queue ID: 0
Step 8: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 41704 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 192 MBytes 1.61 Gbits/sec 0 1.80 MBytes [ 5] 1.00-2.00 sec 198 MBytes 1.65 Gbits/sec 0 2.08 MBytes [ 5] 2.00-3.01 sec 189 MBytes 1.58 Gbits/sec 0 3.10 MBytes [ 5] 3.01-4.00 sec 182 MBytes 1.54 Gbits/sec 0 3.10 MBytes [ 5] 4.00-5.00 sec 169 MBytes 1.42 Gbits/sec 39 2.17 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 930 MBytes 1.56 Gbits/sec 39 sender [ 5] 0.00-5.00 sec 930 MBytes 1.56 Gbits/sec receiver iperf Done.
Step 9: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth1Show output
Ethernet Channel Bonding Driver: v5.10.127 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth0 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:10 Slave queue ID: 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:11 Slave queue ID: 0