wlan ---- .. osdx:cfgcmd:: interfaces wlan .. raw:: html M10-Smart M2 RS420 WLAN network :arg wlanN: WLAN network name :instances: Multiple :ref Required: controllers wlan radios * :ref Required: .. osdx:cfgcmd:: interfaces wlan address .. raw:: html M10-Smart M2 RS420 IP address :arg ipv6cidr: IPv6 address and prefix length :arg dhcpv6: Dynamic Host Configuration Protocol for IPv6 :arg ipv4cidr: IPv4 address and prefix length :arg dhcp: Dynamic Host Configuration Protocol :instances: Multiple .. osdx:cfgcmd:: interfaces wlan alarm .. raw:: html M10-Smart M2 RS420 Enable or disable alarm according the link state .. osdx:cfgcmd:: interfaces wlan alarm down .. raw:: html M10-Smart M2 RS420 Alarm to be enabled if the link is down :ref Reference: system alarm * .. osdx:cfgcmd:: interfaces wlan bridge-group .. raw:: html M10-Smart M2 RS420 Add this interface to a bridge group :ref Required: interfaces bridge * .. osdx:cfgcmd:: interfaces wlan bridge-group bridge .. raw:: html M10-Smart M2 RS420 Bridge group name (br[0-9]+) :ref Reference: interfaces bridge * .. osdx:cfgcmd:: interfaces wlan bridge-group isolate .. raw:: html M10-Smart M2 RS420 Isolate port .. osdx:cfgcmd:: interfaces wlan bridge-group stp .. raw:: html M10-Smart M2 RS420 Bridge port Spanning Tree Protocol configuration .. osdx:cfgcmd:: interfaces wlan bridge-group stp admin-edge .. raw:: html M10-Smart M2 RS420 Enable the admin edge state .. osdx:cfgcmd:: interfaces wlan bridge-group stp bpdu-filter .. raw:: html M10-Smart M2 RS420 Enable the BPDU filter capability If enabled, this port will discard any ingress BPDUs and will not issue any BPUs .. osdx:cfgcmd:: interfaces wlan bridge-group stp bpdu-guard .. raw:: html M10-Smart M2 RS420 Enable the bpduguard configuration .. osdx:cfgcmd:: interfaces wlan bridge-group stp cost .. raw:: html M10-Smart M2 RS420 Bridge port cost :arg u32: Auto (0) :arg u32: Bridge port cost (1-65535) .. osdx:cfgcmd:: interfaces wlan bridge-group stp disable-auto-edge .. raw:: html M10-Smart M2 RS420 Enable the auto transition to/from edge state .. osdx:cfgcmd:: interfaces wlan bridge-group stp network-assurance .. raw:: html M10-Smart M2 RS420 Enable the bridge assurance capability .. osdx:cfgcmd:: interfaces wlan bridge-group stp p2p .. raw:: html M10-Smart M2 RS420 :arg txt: Enable Point-2-Point (P2P) detection mode .. osdx:cfgcmd:: interfaces wlan bridge-group stp priority .. raw:: html M10-Smart M2 RS420 Bridge port priority :arg u32: Bridge port priority (0-15) .. osdx:cfgcmd:: interfaces wlan bridge-group vlan .. raw:: html M10-Smart M2 RS420 Enable VLAN in this bridge port :arg u32: VLAN ID (1-4094) :instances: Multiple .. osdx:cfgcmd:: interfaces wlan bridge-group vlan pvid .. raw:: html M10-Smart M2 RS420 This VLAN specified is to be considered a PVID at ingress Any untagged frames will be assigned to this VLAN .. osdx:cfgcmd:: interfaces wlan bridge-group vlan untagged .. raw:: html M10-Smart M2 RS420 This VLAN is to be treated as untagged on egress The bridge will always remove the VLAN tag from egress packets .. osdx:cfgcmd:: interfaces wlan description .. raw:: html M10-Smart M2 RS420 Description :arg id: "Interface description is too long (limit 256 characters)" (1-256) .. osdx:cfgcmd:: interfaces wlan dhcp .. raw:: html M10-Smart M2 RS420 Dynamic Host Configuration Protocol configuration .. osdx:cfgcmd:: interfaces wlan dhcp client .. raw:: html M10-Smart M2 RS420 DHCP client configuration .. osdx:cfgcmd:: interfaces wlan dhcp client fallback .. raw:: html M10-Smart M2 RS420 :arg ipv4cidr: Fallback IP address :arg ipv6cidr: Fallback IP address .. osdx:cfgcmd:: interfaces wlan dhcp client rfc3442-routes .. raw:: html M10-Smart M2 RS420 Install RFC3442 routes received from DHCP server .. osdx:cfgcmd:: interfaces wlan dhcp client send .. raw:: html M10-Smart M2 RS420 Send user-defined options to the DHCP server .. osdx:cfgcmd:: interfaces wlan dhcp client send dhcp-client-identifier .. raw:: html M10-Smart M2 RS420 Include the 'dhcp-client-identifier' option :instances: Unique .. osdx:cfgcmd:: interfaces wlan dhcp client send dhcp-client-identifier base-mac .. raw:: html M10-Smart M2 RS420 Use device base mac as identifier .. osdx:cfgcmd:: interfaces wlan dhcp client send dhcp-client-identifier serial-number .. raw:: html M10-Smart M2 RS420 Use device serial number as identifier .. osdx:cfgcmd:: interfaces wlan dhcp client send dhcp-client-identifier string .. raw:: html M10-Smart M2 RS420 Use a string as identifier :arg id: Identifier string (1-255) .. osdx:cfgcmd:: interfaces wlan dhcp client send vendor-class-identifier .. raw:: html M10-Smart M2 RS420 Include the 'vendor-class-identifier' option :instances: Unique .. osdx:cfgcmd:: interfaces wlan dhcp client send vendor-class-identifier string .. raw:: html M10-Smart M2 RS420 Use a string as identifier :arg id: Identifier string (1-255) .. osdx:cfgcmd:: interfaces wlan dhcpv6 .. raw:: html M10-Smart M2 RS420 Dynamic Host Configuration Protocol v6 configuration .. osdx:cfgcmd:: interfaces wlan dhcpv6 client .. raw:: html M10-Smart M2 RS420 DHCPv6 client configuration .. osdx:cfgcmd:: interfaces wlan dhcpv6 client parameters-only .. raw:: html M10-Smart M2 RS420 Acquire only config parameters, not address .. osdx:cfgcmd:: interfaces wlan dhcpv6 client send .. raw:: html M10-Smart M2 RS420 Send user-defined options to the DHCPv6 server .. osdx:cfgcmd:: interfaces wlan dhcpv6 client send duid .. raw:: html M10-Smart M2 RS420 :arg id: DHCPv6 DUID to be sent by dhcpv6 client .. osdx:cfgcmd:: interfaces wlan dhcpv6 client temporary .. raw:: html M10-Smart M2 RS420 IPv6 "temporary" address .. osdx:cfgcmd:: interfaces wlan disable .. raw:: html M10-Smart M2 RS420 Disable interface .. osdx:cfgcmd:: interfaces wlan disable advisor .. raw:: html M10-Smart M2 RS420 Advisor to enable or disable the interface :ref Reference: system advisor * .. osdx:cfgcmd:: interfaces wlan flow .. raw:: html M10-Smart M2 RS420 Active netflow on interface .. osdx:cfgcmd:: interfaces wlan flow egress .. raw:: html M10-Smart M2 RS420 Active output traffic .. osdx:cfgcmd:: interfaces wlan flow egress selector .. raw:: html M10-Smart M2 RS420 Traffic selector :ref Reference: traffic selector * .. osdx:cfgcmd:: interfaces wlan flow ingress .. raw:: html M10-Smart M2 RS420 Active input traffic .. osdx:cfgcmd:: interfaces wlan flow ingress selector .. raw:: html M10-Smart M2 RS420 Traffic selector :ref Reference: traffic selector * .. osdx:cfgcmd:: interfaces wlan ip .. raw:: html M10-Smart M2 RS420 IPv4 routing parameters .. osdx:cfgcmd:: interfaces wlan ip igmp .. raw:: html M10-Smart M2 RS420 Internet Group Management Protocol (IGMP) parameters .. osdx:cfgcmd:: interfaces wlan ip igmp join .. raw:: html M10-Smart M2 RS420 Join multicast group :arg ipv4: Join multicast group on this interface .. osdx:cfgcmd:: interfaces wlan ip igmp last-member-query-count .. raw:: html M10-Smart M2 RS420 IGMP last member query count :arg u32: IGMP last member query count (1-255) .. osdx:cfgcmd:: interfaces wlan ip igmp last-member-query-interval .. raw:: html M10-Smart M2 RS420 IGMP last member query interval :arg u32: IGMP last member query interval in deciseconds (1-65535) .. osdx:cfgcmd:: interfaces wlan ip igmp query-interval .. raw:: html M10-Smart M2 RS420 IGMP query interval :arg u32: IGMP query interval in seconds (1-65535) .. osdx:cfgcmd:: interfaces wlan ip igmp query-max-response-time .. raw:: html M10-Smart M2 RS420 IGMP query response timeout value :arg u32: IGMP query response timeout value in deciseconds (1-65535) .. osdx:cfgcmd:: interfaces wlan ip igmp version .. raw:: html M10-Smart M2 RS420 IGMP version :arg u32: IGMP version used on this interface (2-3) .. osdx:cfgcmd:: interfaces wlan ip multicast .. raw:: html M10-Smart M2 RS420 Multicast parameters .. osdx:cfgcmd:: interfaces wlan ip multicast boundary-list .. raw:: html M10-Smart M2 RS420 Prefix-list to control for which groups to accept or ignore received PIM join or IGMP report messages :ref Reference: protocols ip prefix-list * .. osdx:cfgcmd:: interfaces wlan ip ospf .. raw:: html M10-Smart M2 RS420 Open Shortest Path First (OSPF) parameters .. osdx:cfgcmd:: interfaces wlan ip ospf authentication .. raw:: html M10-Smart M2 RS420 OSPF interface authentication .. osdx:cfgcmd:: interfaces wlan ip ospf authentication encrypted-password .. raw:: html M10-Smart M2 RS420 :arg password: Encrypted password .. osdx:cfgcmd:: interfaces wlan ip ospf authentication message-digest .. raw:: html M10-Smart M2 RS420 MD5 authentication parameters :arg id: MD5 ID number (1-255) :instances: Multiple .. osdx:cfgcmd:: interfaces wlan ip ospf authentication message-digest encrypted-password .. raw:: html M10-Smart M2 RS420 :arg password: MD5 encrypted key .. osdx:cfgcmd:: interfaces wlan ip ospf authentication message-digest password .. raw:: html M10-Smart M2 RS420 MD5 key :arg txt: MD5 Key (1-16) .. osdx:cfgcmd:: interfaces wlan ip ospf authentication password .. raw:: html M10-Smart M2 RS420 :arg txt: Plain text password .. osdx:cfgcmd:: interfaces wlan ip ospf bandwidth .. raw:: html M10-Smart M2 RS420 Bandwidth of interface (kilobits/sec) :arg u32: Bandwidth in kilobits/sec (for calculating OSPF cost) (1-10000000) .. osdx:cfgcmd:: interfaces wlan ip ospf cost .. raw:: html M10-Smart M2 RS420 Interface cost :arg u32: OSPF interface cost (1-65535) .. osdx:cfgcmd:: interfaces wlan ip ospf dead-interval .. raw:: html M10-Smart M2 RS420 Interval after which neighbor is dead :arg u32: OSPF dead interval in seconds (1-65535) .. osdx:cfgcmd:: interfaces wlan ip ospf hello-interval .. raw:: html M10-Smart M2 RS420 Interval between hello packets :arg u32: Interval between OSPF hello packets in seconds (1-65535) .. osdx:cfgcmd:: interfaces wlan ip ospf mtu-ignore .. raw:: html M10-Smart M2 RS420 Disable Maximum Transmission Unit (MTU) mismatch detection .. osdx:cfgcmd:: interfaces wlan ip ospf network .. raw:: html M10-Smart M2 RS420 Network type :arg broadcast: Broadcast network type :arg non-broadcast: Non-broadcast network type :arg point-to-multipoint: Point-to-multipoint network type :arg point-to-point: Point-to-point network type .. osdx:cfgcmd:: interfaces wlan ip ospf priority .. raw:: html M10-Smart M2 RS420 Router priority :arg u32: Priority (0-255) .. osdx:cfgcmd:: interfaces wlan ip ospf retransmit-interval .. raw:: html M10-Smart M2 RS420 Interval between retransmitting lost link state advertisements :arg u32: Retransmit interval in seconds (3-65535) .. osdx:cfgcmd:: interfaces wlan ip ospf transmit-delay .. raw:: html M10-Smart M2 RS420 Link state transmit delay :arg u32: Transmit delay in seconds (1-65535) .. osdx:cfgcmd:: interfaces wlan ip pim .. raw:: html M10-Smart M2 RS420 Protocol Independent Multicast (PIM) parameters .. osdx:cfgcmd:: interfaces wlan ip pim disable-bsm .. raw:: html M10-Smart M2 RS420 Disable sending and receiving bootstrap messages .. osdx:cfgcmd:: interfaces wlan ip pim disable-unicast-bsm .. raw:: html M10-Smart M2 RS420 Disable sending and receiving unicast bootstrap messages .. osdx:cfgcmd:: interfaces wlan ip pim drpriority .. raw:: html M10-Smart M2 RS420 PIM Designated Router (DR) priority :arg u32: PIM DR priority for the interface (1-4294967295) .. osdx:cfgcmd:: interfaces wlan ip pim hello .. raw:: html M10-Smart M2 RS420 PIM hello interval :arg u32: PIM hello interval in seconds (1-255) .. osdx:cfgcmd:: interfaces wlan ip pim passive .. raw:: html M10-Smart M2 RS420 Disable sending and receiving all PIM control messages (such as: ASSERT, BSM, HELLO, JOIN, PRUNE, REGISTER, REGISTER-STOP) .. osdx:cfgcmd:: interfaces wlan ip reverse-path-filter .. raw:: html M10-Smart M2 RS420 Policy for source validation by reversed path, as specified in RFC3704 :arg strict: Enable Strict Reverse Path Forwarding as defined in RFC3704 :arg loose: Enable Loose Reverse Path Forwarding as defined in RFC3704 :arg disable: No source validation .. osdx:cfgcmd:: interfaces wlan ip rip .. raw:: html M10-Smart M2 RS420 Routing Information Protocol (RIP) parameters .. osdx:cfgcmd:: interfaces wlan ip rip authentication .. raw:: html M10-Smart M2 RS420 Authentication method .. osdx:cfgcmd:: interfaces wlan ip rip authentication encrypted-password .. raw:: html M10-Smart M2 RS420 :arg password: Encrypted password .. osdx:cfgcmd:: interfaces wlan ip rip authentication message-digest .. raw:: html M10-Smart M2 RS420 MD5 authentication parameters :arg u32: MD5 ID number (1-255) :instances: Multiple .. osdx:cfgcmd:: interfaces wlan ip rip authentication message-digest encrypted-password .. raw:: html M10-Smart M2 RS420 :arg password: MD5 encrypted key .. osdx:cfgcmd:: interfaces wlan ip rip authentication message-digest password .. raw:: html M10-Smart M2 RS420 MD5 key :arg txt: MD5 Key (1-16) .. osdx:cfgcmd:: interfaces wlan ip rip authentication password .. raw:: html M10-Smart M2 RS420 Plain text password :arg txt: Plain text password (1-16) .. osdx:cfgcmd:: interfaces wlan ip rip split-horizon .. raw:: html M10-Smart M2 RS420 Split horizon parameters .. osdx:cfgcmd:: interfaces wlan ip rip split-horizon disable .. raw:: html M10-Smart M2 RS420 Disable split horizon on specified interface .. osdx:cfgcmd:: interfaces wlan ip rip split-horizon poison-reverse .. raw:: html M10-Smart M2 RS420 Enable poison reverse for split-horizon .. osdx:cfgcmd:: interfaces wlan ipv6 .. raw:: html M10-Smart M2 RS420 IPv6 routing parameters .. osdx:cfgcmd:: interfaces wlan ipv6 address .. raw:: html M10-Smart M2 RS420 IPv6 address auto-configuration modes .. osdx:cfgcmd:: interfaces wlan ipv6 address autoconf .. raw:: html M10-Smart M2 RS420 Enable acquisition of IPv6 address using stateless autoconfig .. osdx:cfgcmd:: interfaces wlan ipv6 address eui64 .. raw:: html M10-Smart M2 RS420 Assign IPv6 address using EUI-64 based on MAC address :arg ipv6net: 64-bit IPv6 prefix to use with EUI-64 to make address :instances: Multiple .. osdx:cfgcmd:: interfaces wlan ipv6 address prefix-from-provider .. raw:: html M10-Smart M2 RS420 :arg id: IPv6 from Learned Prefix :instances: Multiple .. osdx:cfgcmd:: interfaces wlan ipv6 address prefix-from-provider ifc-ID .. raw:: html M10-Smart M2 RS420 Assign IPv6 address using Learned Prefixes :arg <: 64-bit IPv6 prefix (:h:h:h:h/64>) :instances: Multiple .. osdx:cfgcmd:: interfaces wlan ipv6 dhcp-client-pd .. raw:: html M10-Smart M2 RS420 :arg id: Name of learned prefix from provider .. osdx:cfgcmd:: interfaces wlan ipv6 disable-forwarding .. raw:: html M10-Smart M2 RS420 Disable IPv6 forwarding on this interface only .. osdx:cfgcmd:: interfaces wlan ipv6 dup-addr-detect-transmits .. raw:: html M10-Smart M2 RS420 Number of NS messages to send while performing DAD :arg u32: Number of NS messages to send while performing DAD (0-2147483647) .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 .. raw:: html M10-Smart M2 RS420 IPv6 Open Shortest Path First (OSPFv3) parameters .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 cost .. raw:: html M10-Smart M2 RS420 Interface cost :arg u32: OSPFv3 cost (1-65535) .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 dead-interval .. raw:: html M10-Smart M2 RS420 Interval after which neighbor is declared dead :arg u32: Neighbor dead interval in seconds (1-65535) .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 hello-interval .. raw:: html M10-Smart M2 RS420 Interval between hello packets :arg u32: Interval between OSPFv3 hello packets in seconds (1-65535) .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 ifmtu .. raw:: html M10-Smart M2 RS420 Interface MTU :arg u32: Interface MTU value (1-65535) .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 instance-id .. raw:: html M10-Smart M2 RS420 Instance-id :arg u32: Instance Id (0-255) .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 mtu-ignore .. raw:: html M10-Smart M2 RS420 Disable Maximum Transmission Unit mismatch detection .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 passive .. raw:: html M10-Smart M2 RS420 Disable forming of adjacency .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 priority .. raw:: html M10-Smart M2 RS420 Router priority :arg u32: Priority (0-255) .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 retransmit-interval .. raw:: html M10-Smart M2 RS420 Interval between retransmitting lost link state advertisements :arg u32: Retransmit interval in seconds (3-65535) .. osdx:cfgcmd:: interfaces wlan ipv6 ospfv3 transmit-delay .. raw:: html M10-Smart M2 RS420 Link state transmit delay :arg u32: Link state transmit delay (1-65535) .. osdx:cfgcmd:: interfaces wlan ipv6 ripng .. raw:: html M10-Smart M2 RS420 Routing Information Protocol (RIPng) .. osdx:cfgcmd:: interfaces wlan ipv6 ripng split-horizon .. raw:: html M10-Smart M2 RS420 Split horizon parameters .. osdx:cfgcmd:: interfaces wlan ipv6 ripng split-horizon disable .. raw:: html M10-Smart M2 RS420 Disable split horizon .. osdx:cfgcmd:: interfaces wlan ipv6 ripng split-horizon poison-reverse .. raw:: html M10-Smart M2 RS420 Enable poison reverse for split-horizon .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert .. raw:: html M10-Smart M2 RS420 Configure parameters for sending Router Advertisements (RAs) .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert cur-hop-limit .. raw:: html M10-Smart M2 RS420 Value to be placed in the Current Hop Limit field in RAs :arg u32: Value to place in the Current Hop Limit field in RAs (0-255) .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert default-lifetime .. raw:: html M10-Smart M2 RS420 Value to be placed in Router Lifetime field in RAs :arg u32: Value in seconds to be placed in Router Lifetime field in RAs (4-9000) :arg u32: This means "not a default router", in Router Lifetime field (0) .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert default-preference .. raw:: html M10-Smart M2 RS420 Default router preference :arg low: Default router is low preference :arg medium: Default router is medium preference :arg high: Default router is high preference .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert link-mtu .. raw:: html M10-Smart M2 RS420 Value of link MTU to place in RAs :arg u32: Do not send MTU options in RAs (0) :arg u32: Value of link MTU to place in RAs (1280-2147483647) .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert managed-flag .. raw:: html M10-Smart M2 RS420 :arg txt: Value for "managed address configuration" flag in RAs .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert max-interval .. raw:: html M10-Smart M2 RS420 Maximum interval between unsolicited multicast RAs :arg u32: Maximum interval in seconds between unsolicited multicast RAs (4-1800) .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert min-interval .. raw:: html M10-Smart M2 RS420 Minimum interval between unsolicited multicast RAs :arg u32: Minimum interval in seconds between unsolicited multicast RAs (3-1350) .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert name-server .. raw:: html M10-Smart M2 RS420 :arg ipv6: IPv6 address of a Recursive DNS Server :instances: Multiple .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert other-config-flag .. raw:: html M10-Smart M2 RS420 :arg txt: Value to be placed in the "other configuration" flag in RAs .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert prefix .. raw:: html M10-Smart M2 RS420 IPv6 prefix to be advertised in Router Advertisements (RAs) :arg ipv6net: IPv6 prefix to be advertized in Router Advertisements (RAs) :instances: Multiple .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert prefix autonomous-flag .. raw:: html M10-Smart M2 RS420 :arg txt: Whether prefix can be used for address auto-configuration .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert prefix on-link-flag .. raw:: html M10-Smart M2 RS420 :arg txt: Flag that prefix can be used for on-link determination .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert prefix preferred-lifetime .. raw:: html M10-Smart M2 RS420 Time in seconds that the prefix will remain preferred :arg u32: Time in seconds that the prefix will remain preferred (0-2147483647) :arg infinity: Prefix will remain preferred forever .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert prefix valid-lifetime .. raw:: html M10-Smart M2 RS420 Time in seconds that the prefix will remain valid :arg u32: Time in seconds that the prefix will remain valid (0-2147483647) :arg infinity: Prefix will remain valid forever .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert reachable-time .. raw:: html M10-Smart M2 RS420 Value to be placed in "Reachable Time" field in RAs :arg u32: Reachable Time value in RAs (in milliseconds) (1-3600000) :arg u32: Reachable Time 0 (i.e., unspecified by this router) (0) .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert retrans-timer .. raw:: html M10-Smart M2 RS420 Value to place in "Retrans Timer" field in RAs. :arg u32: Value in milliseconds to place in "Retrans Timer" field in RAs (0-2147483647) .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert send-advert .. raw:: html M10-Smart M2 RS420 :arg txt: Enable/disable sending RAs .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert used-prefixes .. raw:: html M10-Smart M2 RS420 Delegate prefixes used on the interface .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert used-prefixes autonomous-flag .. raw:: html M10-Smart M2 RS420 :arg txt: Whether prefix can be used for address auto-configuration .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert used-prefixes on-link-flag .. raw:: html M10-Smart M2 RS420 :arg txt: Flag that prefix can be used for on-link determination .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert used-prefixes preferred-lifetime .. raw:: html M10-Smart M2 RS420 Time in seconds that the prefix will remain preferred :arg u32: Time in seconds that the prefix will remain preferred (0-2147483647) :arg infinity: Prefix will remain preferred forever .. osdx:cfgcmd:: interfaces wlan ipv6 router-advert used-prefixes valid-lifetime .. raw:: html M10-Smart M2 RS420 Time in seconds that the prefix will remain valid :arg u32: Time in seconds that the prefix will remain valid (0-2147483647) :arg infinity: Prefix will remain valid forever .. osdx:cfgcmd:: interfaces wlan phy .. raw:: html M10-Smart M2 RS420 Specify the physical interface for that Virtual WLAN interface. :ref Reference: controllers wlan radios * .. osdx:cfgcmd:: interfaces wlan tcp-mss .. raw:: html M10-Smart M2 RS420 :arg u32: Change tcp-mss value .. osdx:cfgcmd:: interfaces wlan traffic .. raw:: html M10-Smart M2 RS420 Traffic processing options .. osdx:cfgcmd:: interfaces wlan traffic control .. raw:: html M10-Smart M2 RS420 Traffic control for interface .. osdx:cfgcmd:: interfaces wlan traffic control in .. raw:: html M10-Smart M2 RS420 Ingress traffic control for interface :ref Reference: traffic control * .. osdx:cfgcmd:: interfaces wlan traffic control out .. raw:: html M10-Smart M2 RS420 Egress traffic control for interface :ref Reference: traffic control * .. osdx:cfgcmd:: interfaces wlan traffic nat .. raw:: html M10-Smart M2 RS420 Network Address Translation (NAT) parameters .. osdx:cfgcmd:: interfaces wlan traffic nat destination .. raw:: html M10-Smart M2 RS420 Destination NAT settings .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule .. raw:: html M10-Smart M2 RS420 Rule number for NAT :arg u32: Number for this NAT rule (1-9999) :instances: Multiple .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule address .. raw:: html M10-Smart M2 RS420 IP address, subnet, range or redirect :arg ipv4: NAT to the specified IP address :arg ipv4net: NAT to the specified network address :arg ipv4range: NAT to the specified IP range :arg redirect: NAT to the interface address .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule description .. raw:: html M10-Smart M2 RS420 :arg txt: Rule description .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule log .. raw:: html M10-Smart M2 RS420 Log packets to which this rule has been applied .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule log level .. raw:: html M10-Smart M2 RS420 Loggin level :arg emerg: Emergency messages :arg alert: Urgent messages :arg crit: Critical messages :arg err: Error messages :arg warn: Warning messages :arg notice: Messages for further investigation :arg info: Informational messages :arg debug: Debug messages .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule log prefix .. raw:: html M10-Smart M2 RS420 :arg txt: Log message prefix text, up to 29 characters .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule network .. raw:: html M10-Smart M2 RS420 IP prefix to use in translation (host part is kept) :arg ipv4net: NAT to the specified network address, host part of the address will remain unchanged .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule port .. raw:: html M10-Smart M2 RS420 NAT port :arg u32: Port to use in PAT (1-65535) :arg range: Port range (pool, for example, 1001-1005) .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule protocol .. raw:: html M10-Smart M2 RS420 :arg txt: NAT transport protocol .. osdx:cfgcmd:: interfaces wlan traffic nat destination rule selector .. raw:: html M10-Smart M2 RS420 Traffic selector :ref Reference: traffic selector * .. osdx:cfgcmd:: interfaces wlan traffic nat source .. raw:: html M10-Smart M2 RS420 Source NAT settings .. osdx:cfgcmd:: interfaces wlan traffic nat source rule .. raw:: html M10-Smart M2 RS420 Rule number for NAT :arg u32: Number for this NAT rule (1-9999) :instances: Multiple .. osdx:cfgcmd:: interfaces wlan traffic nat source rule address .. raw:: html M10-Smart M2 RS420 IP address, subnet, range or masquerade :arg ipv4: NAT to the specified IP address :arg ipv4net: NAT to the specified network address :arg ipv4range: NAT to the specified IP range :arg masquerade: NAT to the interface address .. osdx:cfgcmd:: interfaces wlan traffic nat source rule description .. raw:: html M10-Smart M2 RS420 :arg txt: Rule description .. osdx:cfgcmd:: interfaces wlan traffic nat source rule log .. raw:: html M10-Smart M2 RS420 Log packets to which this rule has been applied .. osdx:cfgcmd:: interfaces wlan traffic nat source rule log level .. raw:: html M10-Smart M2 RS420 Loggin level :arg emerg: Emergency messages :arg alert: Urgent messages :arg crit: Critical messages :arg err: Error messages :arg warn: Warning messages :arg notice: Messages for further investigation :arg info: Informational messages :arg debug: Debug messages .. osdx:cfgcmd:: interfaces wlan traffic nat source rule log prefix .. raw:: html M10-Smart M2 RS420 :arg txt: Log message prefix text, up to 29 characters .. osdx:cfgcmd:: interfaces wlan traffic nat source rule network .. raw:: html M10-Smart M2 RS420 IP prefix to use in translation (host part is kept) :arg ipv4net: NAT to the specified network address, host part of the address will remain unchanged .. osdx:cfgcmd:: interfaces wlan traffic nat source rule port .. raw:: html M10-Smart M2 RS420 NAT port :arg u32: Port to use in PAT (1-65535) :arg range: Port range (pool, for example, 1001-1005) .. osdx:cfgcmd:: interfaces wlan traffic nat source rule protocol .. raw:: html M10-Smart M2 RS420 :arg txt: NAT transport protocol .. osdx:cfgcmd:: interfaces wlan traffic nat source rule selector .. raw:: html M10-Smart M2 RS420 Traffic selector :ref Reference: traffic selector * .. osdx:cfgcmd:: interfaces wlan traffic policy .. raw:: html M10-Smart M2 RS420 Traffic policy rulesets for interface .. osdx:cfgcmd:: interfaces wlan traffic policy in .. raw:: html M10-Smart M2 RS420 Input traffic policy ruleset for interface :ref Reference: traffic policy * :instances: Multiple .. osdx:cfgcmd:: interfaces wlan traffic policy in priority .. raw:: html M10-Smart M2 RS420 Priority order for traffic policy :arg very-high: First policy executed before NAT :arg high: Second policy executed before NAT :arg low: First policy executed after NAT :arg very-low: Second policy executed after NAT .. osdx:cfgcmd:: interfaces wlan traffic policy link .. raw:: html M10-Smart M2 RS420 Link layer traffic policy ruleset for interface :ref Reference: traffic policy * .. osdx:cfgcmd:: interfaces wlan traffic policy local-in .. raw:: html M10-Smart M2 RS420 Local input traffic policy ruleset for interface :ref Reference: traffic policy * :instances: Multiple .. osdx:cfgcmd:: interfaces wlan traffic policy local-in priority .. raw:: html M10-Smart M2 RS420 Priority order for traffic policy :arg very-high: First policy executed :arg high: Second policy executed :arg low: Third policy executed :arg very-low: Fourth policy executed .. osdx:cfgcmd:: interfaces wlan traffic policy local-out .. raw:: html M10-Smart M2 RS420 Local output traffic policy ruleset for interface :ref Reference: traffic policy * :instances: Multiple .. osdx:cfgcmd:: interfaces wlan traffic policy local-out priority .. raw:: html M10-Smart M2 RS420 Priority order for traffic policy :arg very-high: First policy executed :arg high: Second policy executed :arg low: Third policy executed :arg very-low: Fourth policy executed .. osdx:cfgcmd:: interfaces wlan traffic policy out .. raw:: html M10-Smart M2 RS420 Output traffic policy ruleset for interface :ref Reference: traffic policy * :instances: Multiple .. osdx:cfgcmd:: interfaces wlan traffic policy out priority .. raw:: html M10-Smart M2 RS420 Priority order for traffic policy :arg very-high: First policy executed before NAT :arg high: Second policy executed before NAT :arg low: First policy executed after NAT :arg very-low: Second policy executed after NAT .. osdx:cfgcmd:: interfaces wlan traffic zone .. raw:: html M10-Smart M2 RS420 Traffic zone associated with this interface :ref Reference: traffic zone * .. osdx:cfgcmd:: interfaces wlan type .. raw:: html M10-Smart M2 RS420 WLAN interface role configuration :instances: Unique .. osdx:cfgcmd:: interfaces wlan type access-point .. raw:: html M10-Smart M2 RS420 Configures the interface to operate as access point (infrastructure) :ref Required: .. osdx:cfgcmd:: interfaces wlan type access-point client-isolation .. raw:: html M10-Smart M2 RS420 When enabled, clients will be isolated on the WLAN interface .. osdx:cfgcmd:: interfaces wlan type access-point disable-broadcast-ssid .. raw:: html M10-Smart M2 RS420 Disable SSID broadcasting .. osdx:cfgcmd:: interfaces wlan type access-point disable-rates .. raw:: html M10-Smart M2 RS420 Disable selected legacy rates :instances: Unique .. osdx:cfgcmd:: interfaces wlan type access-point disable-rates 802.11a .. raw:: html M10-Smart M2 RS420 List of 802.11a rates to be disabled :arg txt: List of rates in Mbps, comma-separated .. osdx:cfgcmd:: interfaces wlan type access-point disable-rates 802.11g .. raw:: html M10-Smart M2 RS420 List of 802.11b/g rates to be disabled :arg txt: List of rates in Mbps, comma-separated .. osdx:cfgcmd:: interfaces wlan type access-point disable-u-apsd .. raw:: html M10-Smart M2 RS420 Disable WMM Power Save .. osdx:cfgcmd:: interfaces wlan type access-point disable-wmm .. raw:: html M10-Smart M2 RS420 Disable Wi-Fi Multimedia (WMM) .. osdx:cfgcmd:: interfaces wlan type access-point dot11k .. raw:: html M10-Smart M2 RS420 802.11k configuration .. osdx:cfgcmd:: interfaces wlan type access-point dot11k radio-resource-management .. raw:: html M10-Smart M2 RS420 Enable radio resource measurement & management .. osdx:cfgcmd:: interfaces wlan type access-point dot11r .. raw:: html M10-Smart M2 RS420 802.11r configuration .. osdx:cfgcmd:: interfaces wlan type access-point dot11r fast-transition .. raw:: html M10-Smart M2 RS420 Fast roaming configuration :instances: Unique .. osdx:cfgcmd:: interfaces wlan type access-point dot11r fast-transition over-the-air .. raw:: html M10-Smart M2 RS420 Authentication is done by the client over the air .. osdx:cfgcmd:: interfaces wlan type access-point dot11r fast-transition over-the-ds .. raw:: html M10-Smart M2 RS420 Authentication is done by the AP over the Distribution System .. osdx:cfgcmd:: interfaces wlan type access-point dot11v .. raw:: html M10-Smart M2 RS420 802.11v configuration .. osdx:cfgcmd:: interfaces wlan type access-point dot11v network-assisted-roaming .. raw:: html M10-Smart M2 RS420 Enable network assisted roaming .. osdx:cfgcmd:: interfaces wlan type access-point dtim .. raw:: html M10-Smart M2 RS420 Frequency where a beacon frame includes a Delivery Traffic Indication Message :arg u32: Period in beacon-frames (default=2) (1-255) .. osdx:cfgcmd:: interfaces wlan type access-point mac-filter .. raw:: html M10-Smart M2 RS420 MAC address filtering .. osdx:cfgcmd:: interfaces wlan type access-point mac-filter allow-mac .. raw:: html M10-Smart M2 RS420 List of MAC addresses allowed on this interface :arg macaddr: MAC address :instances: Multiple .. osdx:cfgcmd:: interfaces wlan type access-point max-clients .. raw:: html M10-Smart M2 RS420 Maximum number of connected clients .. osdx:cfgcmd:: interfaces wlan type access-point max-clients hard-limit .. raw:: html M10-Smart M2 RS420 Sets the maximum number of simultaneous physical clients :arg u32: Value (0-&VAR(/controllers/wlan/radios/wifi0/caps/stations)) .. osdx:cfgcmd:: interfaces wlan type access-point security .. raw:: html M10-Smart M2 RS420 Security-settings :ref Required: .. osdx:cfgcmd:: interfaces wlan type access-point security aaa .. raw:: html M10-Smart M2 RS420 AAA parameters :ref Required: system aaa list * .. osdx:cfgcmd:: interfaces wlan type access-point security aaa accounting .. raw:: html M10-Smart M2 RS420 Accounting list :ref Reference: system aaa list * .. osdx:cfgcmd:: interfaces wlan type access-point security aaa authentication .. raw:: html M10-Smart M2 RS420 Authentication list :ref Reference: system aaa list * .. osdx:cfgcmd:: interfaces wlan type access-point security akm .. raw:: html M10-Smart M2 RS420 Authentication and Key-Management (AKM) .. osdx:cfgcmd:: interfaces wlan type access-point security akm cnsa .. raw:: html M10-Smart M2 RS420 CNSA 192-bit Suite B security .. osdx:cfgcmd:: interfaces wlan type access-point security akm dot1x-256 .. raw:: html M10-Smart M2 RS420 802.1X with SHA-256 .. osdx:cfgcmd:: interfaces wlan type access-point security akm ft-dot1x .. raw:: html M10-Smart M2 RS420 Fast transition with 802.11x authentication .. osdx:cfgcmd:: interfaces wlan type access-point security akm ft-psk .. raw:: html M10-Smart M2 RS420 Fast transition with pre-shared key .. osdx:cfgcmd:: interfaces wlan type access-point security akm ft-sae .. raw:: html M10-Smart M2 RS420 Fast transition with Simultaneous Authentication of Equals (SAE) .. osdx:cfgcmd:: interfaces wlan type access-point security akm none .. raw:: html M10-Smart M2 RS420 No Wi-Fi security (Open network) .. osdx:cfgcmd:: interfaces wlan type access-point security akm none transition .. raw:: html M10-Smart M2 RS420 OWE transition mode .. osdx:cfgcmd:: interfaces wlan type access-point security akm none transition wlan-ifc .. raw:: html M10-Smart M2 RS420 WLAN interface name :arg txt: WLAN interface name :ref Reference: interfaces wlan * .. osdx:cfgcmd:: interfaces wlan type access-point security akm owe .. raw:: html M10-Smart M2 RS420 Opportunistic Wireless Encryption (OWE). Enhanced Open network .. osdx:cfgcmd:: interfaces wlan type access-point security akm owe transition .. raw:: html M10-Smart M2 RS420 OWE transition mode .. osdx:cfgcmd:: interfaces wlan type access-point security akm owe transition wlan-ifc .. raw:: html M10-Smart M2 RS420 WLAN interface name :arg txt: WLAN interface name :ref Reference: interfaces wlan * .. osdx:cfgcmd:: interfaces wlan type access-point security akm psk-256 .. raw:: html M10-Smart M2 RS420 Pre-Shared Key (PSK) with SHA-256, configured directly or via passphrase .. osdx:cfgcmd:: interfaces wlan type access-point security akm sae .. raw:: html M10-Smart M2 RS420 Simultaneous Authentication of Equals (SAE) .. osdx:cfgcmd:: interfaces wlan type access-point security encrypted-passphrase .. raw:: html M10-Smart M2 RS420 :arg password: Encrypted passphrase .. osdx:cfgcmd:: interfaces wlan type access-point security group-rekeying .. raw:: html M10-Smart M2 RS420 Optional settings for group-rekeying .. osdx:cfgcmd:: interfaces wlan type access-point security group-rekeying interval .. raw:: html M10-Smart M2 RS420 Update-interval in seconds :arg u32: Update-interval in seconds (default=86400) (30-86400) .. osdx:cfgcmd:: interfaces wlan type access-point security group-rekeying strict .. raw:: html M10-Smart M2 RS420 Choose whether to enforce rekeying after each member-disassociation :arg true: Enforce rekeying after each member-disassociation :arg false: Do NOT enforce rekeying after each member-disassociation (default) .. osdx:cfgcmd:: interfaces wlan type access-point security nas-identifier .. raw:: html M10-Smart M2 RS420 :arg txt: NAS-identifier of the interface .. osdx:cfgcmd:: interfaces wlan type access-point security opportunistic-key-caching .. raw:: html M10-Smart M2 RS420 Enable Opportunistic Key Caching .. osdx:cfgcmd:: interfaces wlan type access-point security pairwise-ciphers .. raw:: html M10-Smart M2 RS420 List of supported unicast-cipher-variants for RSN (multicast-variant is derived as weakest one) .. osdx:cfgcmd:: interfaces wlan type access-point security pairwise-ciphers aes-ccmp .. raw:: html M10-Smart M2 RS420 Counter Mode CBC-MAC Protocol (based on AES) .. osdx:cfgcmd:: interfaces wlan type access-point security pairwise-ciphers aes-ccmp-256 .. raw:: html M10-Smart M2 RS420 AES in Counter mode with CBC-MAC with 256-bit key .. osdx:cfgcmd:: interfaces wlan type access-point security pairwise-ciphers aes-gcmp-128 .. raw:: html M10-Smart M2 RS420 AES in Galois/counter mode protocol (GCMP-128) .. osdx:cfgcmd:: interfaces wlan type access-point security pairwise-ciphers aes-gcmp-256 .. raw:: html M10-Smart M2 RS420 AES in Galois/counter mode protocol (GCMP-256) .. osdx:cfgcmd:: interfaces wlan type access-point security pairwise-ciphers tkip .. raw:: html M10-Smart M2 RS420 Temporal Key Integrity Protocol .. osdx:cfgcmd:: interfaces wlan type access-point security pmf .. raw:: html M10-Smart M2 RS420 Protected management frames configuration :instances: Unique .. osdx:cfgcmd:: interfaces wlan type access-point security pmf optional .. raw:: html M10-Smart M2 RS420 Optional Protected Management Frames .. osdx:cfgcmd:: interfaces wlan type access-point security pmf required .. raw:: html M10-Smart M2 RS420 Mandatory Protect Management Frames .. osdx:cfgcmd:: interfaces wlan type access-point security psk-passphrase .. raw:: html M10-Smart M2 RS420 Passphrase for PSK related akms :arg txt: Passphrase (must be printable characters, optionally enclosed by single quotes) (8-63) .. osdx:cfgcmd:: interfaces wlan type access-point security wpav1 .. raw:: html M10-Smart M2 RS420 WPAv1 security parameters .. osdx:cfgcmd:: interfaces wlan type access-point security wpav1 pairwise-ciphers .. raw:: html M10-Smart M2 RS420 List of supported unicast-cipher-variants for WPA (multicast-variant is derived as weakest one) .. osdx:cfgcmd:: interfaces wlan type access-point security wpav1 pairwise-ciphers aes-ccmp .. raw:: html M10-Smart M2 RS420 Counter Mode CBC-MAC Protocol (based on AES) .. osdx:cfgcmd:: interfaces wlan type access-point security wpav1 pairwise-ciphers tkip .. raw:: html M10-Smart M2 RS420 Temporal Key Integrity Protocol .. osdx:cfgcmd:: interfaces wlan type access-point ssid .. raw:: html M10-Smart M2 RS420 SSID/ESSID for WLAN network :arg txt: SSID/ESSID for WLAN network (1-32) .. osdx:cfgcmd:: interfaces wlan type access-point wds .. raw:: html M10-Smart M2 RS420 Wireless Distribution System .. osdx:cfgcmd:: interfaces wlan type station .. raw:: html M10-Smart M2 RS420 Configures the interface to operate as station/client .. osdx:cfgcmd:: interfaces wlan type station network .. raw:: html M10-Smart M2 RS420 List of conditions for connecting to a target network :arg u32: Network priority (1 the highest, 16 the lowest) (1-16) :instances: Multiple :ref Required: :ref Required: .. osdx:cfgcmd:: interfaces wlan type station network bssid .. raw:: html M10-Smart M2 RS420 Basic Service Set Identifier (BSSID) of the target network :arg macaddr: 12-hex string (48-bit label), colon-separated .. osdx:cfgcmd:: interfaces wlan type station network