cellular -------- .. osdx:cfgcmd:: interfaces cellular .. raw:: html M10-Smart RS420 Cellular interface name :arg cellN: Cellular interface name :instances: Multiple .. osdx:cfgcmd:: interfaces cellular address .. raw:: html M10-Smart RS420 IP address :arg ipv6cidr: IPv6 address and prefix length :arg dhcpv6: Dynamic Host Configuration Protocol for IPv6 :arg ipv4cidr: IPv4 address and prefix length :arg dhcp: Dynamic Host Configuration Protocol :instances: Multiple .. osdx:cfgcmd:: interfaces cellular alarm .. raw:: html M10-Smart RS420 Enable or disable alarm according the link state .. osdx:cfgcmd:: interfaces cellular alarm down .. raw:: html M10-Smart RS420 Alarm to be enabled if the link is down :ref Reference: system alarm * .. osdx:cfgcmd:: interfaces cellular bridge-group .. raw:: html M10-Smart RS420 Add this interface to a bridge group :ref Required: interfaces bridge * .. osdx:cfgcmd:: interfaces cellular bridge-group bridge .. raw:: html M10-Smart RS420 Bridge group name (br[0-9]+) :ref Reference: interfaces bridge * .. osdx:cfgcmd:: interfaces cellular bridge-group isolate .. raw:: html M10-Smart RS420 Isolate port .. osdx:cfgcmd:: interfaces cellular bridge-group stp .. raw:: html M10-Smart RS420 Bridge port Spanning Tree Protocol configuration .. osdx:cfgcmd:: interfaces cellular bridge-group stp admin-edge .. raw:: html M10-Smart RS420 Enable the admin edge state .. osdx:cfgcmd:: interfaces cellular bridge-group stp bpdu-filter .. raw:: html M10-Smart RS420 Enable the BPDU filter capability If enabled, this port will discard any ingress BPDUs and will not issue any BPUs .. osdx:cfgcmd:: interfaces cellular bridge-group stp bpdu-guard .. raw:: html M10-Smart RS420 Enable the bpduguard configuration .. osdx:cfgcmd:: interfaces cellular bridge-group stp cost .. raw:: html M10-Smart RS420 Bridge port cost :arg u32: Auto (0) :arg u32: Bridge port cost (1-65535) .. osdx:cfgcmd:: interfaces cellular bridge-group stp disable-auto-edge .. raw:: html M10-Smart RS420 Enable the auto transition to/from edge state .. osdx:cfgcmd:: interfaces cellular bridge-group stp network-assurance .. raw:: html M10-Smart RS420 Enable the bridge assurance capability .. osdx:cfgcmd:: interfaces cellular bridge-group stp p2p .. raw:: html M10-Smart RS420 :arg txt: Enable Point-2-Point (P2P) detection mode .. osdx:cfgcmd:: interfaces cellular bridge-group stp priority .. raw:: html M10-Smart RS420 Bridge port priority :arg u32: Bridge port priority (0-15) .. osdx:cfgcmd:: interfaces cellular bridge-group vlan .. raw:: html M10-Smart RS420 Enable VLAN in this bridge port :arg u32: VLAN ID (1-4094) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular bridge-group vlan pvid .. raw:: html M10-Smart RS420 This VLAN specified is to be considered a PVID at ingress Any untagged frames will be assigned to this VLAN .. osdx:cfgcmd:: interfaces cellular bridge-group vlan untagged .. raw:: html M10-Smart RS420 This VLAN is to be treated as untagged on egress The bridge will always remove the VLAN tag from egress packets .. osdx:cfgcmd:: interfaces cellular description .. raw:: html M10-Smart RS420 Description :arg id: "Interface description is too long (limit 256 characters)" (1-256) .. osdx:cfgcmd:: interfaces cellular dhcp .. raw:: html M10-Smart RS420 Dynamic Host Configuration Protocol configuration .. osdx:cfgcmd:: interfaces cellular dhcp client .. raw:: html M10-Smart RS420 DHCP client configuration .. osdx:cfgcmd:: interfaces cellular dhcp client fallback .. raw:: html M10-Smart RS420 :arg ipv4cidr: Fallback IP address :arg ipv6cidr: Fallback IP address .. osdx:cfgcmd:: interfaces cellular dhcp client rfc3442-routes .. raw:: html M10-Smart RS420 Install RFC3442 routes received from DHCP server .. osdx:cfgcmd:: interfaces cellular dhcp client send .. raw:: html M10-Smart RS420 Send user-defined options to the DHCP server .. osdx:cfgcmd:: interfaces cellular dhcp client send dhcp-client-identifier .. raw:: html M10-Smart RS420 Include the 'dhcp-client-identifier' option :instances: Unique .. osdx:cfgcmd:: interfaces cellular dhcp client send dhcp-client-identifier base-mac .. raw:: html M10-Smart RS420 Use device base mac as identifier .. osdx:cfgcmd:: interfaces cellular dhcp client send dhcp-client-identifier serial-number .. raw:: html M10-Smart RS420 Use device serial number as identifier .. osdx:cfgcmd:: interfaces cellular dhcp client send dhcp-client-identifier string .. raw:: html M10-Smart RS420 Use a string as identifier :arg id: Identifier string (1-255) .. osdx:cfgcmd:: interfaces cellular dhcp client send vendor-class-identifier .. raw:: html M10-Smart RS420 Include the 'vendor-class-identifier' option :instances: Unique .. osdx:cfgcmd:: interfaces cellular dhcp client send vendor-class-identifier string .. raw:: html M10-Smart RS420 Use a string as identifier :arg id: Identifier string (1-255) .. osdx:cfgcmd:: interfaces cellular dhcpv6 .. raw:: html M10-Smart RS420 Dynamic Host Configuration Protocol v6 configuration .. osdx:cfgcmd:: interfaces cellular dhcpv6 client .. raw:: html M10-Smart RS420 DHCPv6 client configuration .. osdx:cfgcmd:: interfaces cellular dhcpv6 client parameters-only .. raw:: html M10-Smart RS420 Acquire only config parameters, not address .. osdx:cfgcmd:: interfaces cellular dhcpv6 client send .. raw:: html M10-Smart RS420 Send user-defined options to the DHCPv6 server .. osdx:cfgcmd:: interfaces cellular dhcpv6 client send duid .. raw:: html M10-Smart RS420 :arg id: DHCPv6 DUID to be sent by dhcpv6 client .. osdx:cfgcmd:: interfaces cellular dhcpv6 client temporary .. raw:: html M10-Smart RS420 IPv6 "temporary" address .. osdx:cfgcmd:: interfaces cellular disable .. raw:: html M10-Smart RS420 Disable interface .. osdx:cfgcmd:: interfaces cellular disable advisor .. raw:: html M10-Smart RS420 Advisor to enable or disable the interface :ref Reference: system advisor * .. osdx:cfgcmd:: interfaces cellular flow .. raw:: html M10-Smart RS420 Active netflow on interface .. osdx:cfgcmd:: interfaces cellular flow egress .. raw:: html M10-Smart RS420 Active output traffic .. osdx:cfgcmd:: interfaces cellular flow egress selector .. raw:: html M10-Smart RS420 Traffic selector :ref Reference: traffic selector * .. osdx:cfgcmd:: interfaces cellular flow ingress .. raw:: html M10-Smart RS420 Active input traffic .. osdx:cfgcmd:: interfaces cellular flow ingress selector .. raw:: html M10-Smart RS420 Traffic selector :ref Reference: traffic selector * .. osdx:cfgcmd:: interfaces cellular ip .. raw:: html M10-Smart RS420 IPv4 routing parameters .. osdx:cfgcmd:: interfaces cellular ip igmp .. raw:: html M10-Smart RS420 Internet Group Management Protocol (IGMP) parameters .. osdx:cfgcmd:: interfaces cellular ip igmp join .. raw:: html M10-Smart RS420 Join multicast group :arg ipv4: Join multicast group on this interface .. osdx:cfgcmd:: interfaces cellular ip igmp last-member-query-count .. raw:: html M10-Smart RS420 IGMP last member query count :arg u32: IGMP last member query count (1-255) .. osdx:cfgcmd:: interfaces cellular ip igmp last-member-query-interval .. raw:: html M10-Smart RS420 IGMP last member query interval :arg u32: IGMP last member query interval in deciseconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ip igmp query-interval .. raw:: html M10-Smart RS420 IGMP query interval :arg u32: IGMP query interval in seconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ip igmp query-max-response-time .. raw:: html M10-Smart RS420 IGMP query response timeout value :arg u32: IGMP query response timeout value in deciseconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ip igmp version .. raw:: html M10-Smart RS420 IGMP version :arg u32: IGMP version used on this interface (2-3) .. osdx:cfgcmd:: interfaces cellular ip multicast .. raw:: html M10-Smart RS420 Multicast parameters .. osdx:cfgcmd:: interfaces cellular ip multicast boundary-list .. raw:: html M10-Smart RS420 Prefix-list to control for which groups to accept or ignore received PIM join or IGMP report messages :ref Reference: protocols ip prefix-list * .. osdx:cfgcmd:: interfaces cellular ip ospf .. raw:: html M10-Smart RS420 Open Shortest Path First (OSPF) parameters .. osdx:cfgcmd:: interfaces cellular ip ospf authentication .. raw:: html M10-Smart RS420 OSPF interface authentication .. osdx:cfgcmd:: interfaces cellular ip ospf authentication encrypted-password .. raw:: html M10-Smart RS420 :arg password: Encrypted password .. osdx:cfgcmd:: interfaces cellular ip ospf authentication message-digest .. raw:: html M10-Smart RS420 MD5 authentication parameters :arg id: MD5 ID number (1-255) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ip ospf authentication message-digest encrypted-password .. raw:: html M10-Smart RS420 :arg password: MD5 encrypted key .. osdx:cfgcmd:: interfaces cellular ip ospf authentication message-digest password .. raw:: html M10-Smart RS420 MD5 key :arg txt: MD5 Key (1-16) .. osdx:cfgcmd:: interfaces cellular ip ospf authentication password .. raw:: html M10-Smart RS420 :arg txt: Plain text password .. osdx:cfgcmd:: interfaces cellular ip ospf bandwidth .. raw:: html M10-Smart RS420 Bandwidth of interface (kilobits/sec) :arg u32: Bandwidth in kilobits/sec (for calculating OSPF cost) (1-10000000) .. osdx:cfgcmd:: interfaces cellular ip ospf cost .. raw:: html M10-Smart RS420 Interface cost :arg u32: OSPF interface cost (1-65535) .. osdx:cfgcmd:: interfaces cellular ip ospf dead-interval .. raw:: html M10-Smart RS420 Interval after which neighbor is dead :arg u32: OSPF dead interval in seconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ip ospf hello-interval .. raw:: html M10-Smart RS420 Interval between hello packets :arg u32: Interval between OSPF hello packets in seconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ip ospf mtu-ignore .. raw:: html M10-Smart RS420 Disable Maximum Transmission Unit (MTU) mismatch detection .. osdx:cfgcmd:: interfaces cellular ip ospf network .. raw:: html M10-Smart RS420 Network type :arg broadcast: Broadcast network type :arg non-broadcast: Non-broadcast network type :arg point-to-multipoint: Point-to-multipoint network type :arg point-to-point: Point-to-point network type .. osdx:cfgcmd:: interfaces cellular ip ospf priority .. raw:: html M10-Smart RS420 Router priority :arg u32: Priority (0-255) .. osdx:cfgcmd:: interfaces cellular ip ospf retransmit-interval .. raw:: html M10-Smart RS420 Interval between retransmitting lost link state advertisements :arg u32: Retransmit interval in seconds (3-65535) .. osdx:cfgcmd:: interfaces cellular ip ospf transmit-delay .. raw:: html M10-Smart RS420 Link state transmit delay :arg u32: Transmit delay in seconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ip pim .. raw:: html M10-Smart RS420 Protocol Independent Multicast (PIM) parameters .. osdx:cfgcmd:: interfaces cellular ip pim disable-bsm .. raw:: html M10-Smart RS420 Disable sending and receiving bootstrap messages .. osdx:cfgcmd:: interfaces cellular ip pim disable-unicast-bsm .. raw:: html M10-Smart RS420 Disable sending and receiving unicast bootstrap messages .. osdx:cfgcmd:: interfaces cellular ip pim drpriority .. raw:: html M10-Smart RS420 PIM Designated Router (DR) priority :arg u32: PIM DR priority for the interface (1-4294967295) .. osdx:cfgcmd:: interfaces cellular ip pim hello .. raw:: html M10-Smart RS420 PIM hello interval :arg u32: PIM hello interval in seconds (1-255) .. osdx:cfgcmd:: interfaces cellular ip pim passive .. raw:: html M10-Smart RS420 Disable sending and receiving all PIM control messages (such as: ASSERT, BSM, HELLO, JOIN, PRUNE, REGISTER, REGISTER-STOP) .. osdx:cfgcmd:: interfaces cellular ip reverse-path-filter .. raw:: html M10-Smart RS420 Policy for source validation by reversed path, as specified in RFC3704 :arg strict: Enable Strict Reverse Path Forwarding as defined in RFC3704 :arg loose: Enable Loose Reverse Path Forwarding as defined in RFC3704 :arg disable: No source validation .. osdx:cfgcmd:: interfaces cellular ip rip .. raw:: html M10-Smart RS420 Routing Information Protocol (RIP) parameters .. osdx:cfgcmd:: interfaces cellular ip rip authentication .. raw:: html M10-Smart RS420 Authentication method .. osdx:cfgcmd:: interfaces cellular ip rip authentication encrypted-password .. raw:: html M10-Smart RS420 :arg password: Encrypted password .. osdx:cfgcmd:: interfaces cellular ip rip authentication message-digest .. raw:: html M10-Smart RS420 MD5 authentication parameters :arg u32: MD5 ID number (1-255) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ip rip authentication message-digest encrypted-password .. raw:: html M10-Smart RS420 :arg password: MD5 encrypted key .. osdx:cfgcmd:: interfaces cellular ip rip authentication message-digest password .. raw:: html M10-Smart RS420 MD5 key :arg txt: MD5 Key (1-16) .. osdx:cfgcmd:: interfaces cellular ip rip authentication password .. raw:: html M10-Smart RS420 Plain text password :arg txt: Plain text password (1-16) .. osdx:cfgcmd:: interfaces cellular ip rip split-horizon .. raw:: html M10-Smart RS420 Split horizon parameters .. osdx:cfgcmd:: interfaces cellular ip rip split-horizon disable .. raw:: html M10-Smart RS420 Disable split horizon on specified interface .. osdx:cfgcmd:: interfaces cellular ip rip split-horizon poison-reverse .. raw:: html M10-Smart RS420 Enable poison reverse for split-horizon .. osdx:cfgcmd:: interfaces cellular ipv6 .. raw:: html M10-Smart RS420 IPv6 routing parameters .. osdx:cfgcmd:: interfaces cellular ipv6 address .. raw:: html M10-Smart RS420 IPv6 address auto-configuration modes .. osdx:cfgcmd:: interfaces cellular ipv6 address autoconf .. raw:: html M10-Smart RS420 Enable acquisition of IPv6 address using stateless autoconfig .. osdx:cfgcmd:: interfaces cellular ipv6 address eui64 .. raw:: html M10-Smart RS420 Assign IPv6 address using EUI-64 based on MAC address :arg ipv6net: 64-bit IPv6 prefix to use with EUI-64 to make address :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ipv6 address prefix-from-provider .. raw:: html M10-Smart RS420 :arg id: IPv6 from Learned Prefix :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ipv6 address prefix-from-provider ifc-ID .. raw:: html M10-Smart RS420 Assign IPv6 address using Learned Prefixes :arg <: 64-bit IPv6 prefix (:h:h:h:h/64>) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ipv6 dhcp-client-pd .. raw:: html M10-Smart RS420 :arg id: Name of learned prefix from provider .. osdx:cfgcmd:: interfaces cellular ipv6 disable-forwarding .. raw:: html M10-Smart RS420 Disable IPv6 forwarding on this interface only .. osdx:cfgcmd:: interfaces cellular ipv6 dup-addr-detect-transmits .. raw:: html M10-Smart RS420 Number of NS messages to send while performing DAD :arg u32: Number of NS messages to send while performing DAD (0-2147483647) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 .. raw:: html M10-Smart RS420 IPv6 Open Shortest Path First (OSPFv3) parameters .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 area .. raw:: html M10-Smart RS420 OSPFv3 Area :arg u32: OSPFv3 area in decimal notation (0-4294967295) :arg ipv4: OSPFv3 area in dotted decimal notation .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 authentication .. raw:: html M10-Smart RS420 OSPFv3 interface authentication :instances: Unique .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 authentication hmac-sha-256 .. raw:: html M10-Smart RS420 HMAC-SHA-256 authentication parameters :arg u32: HMAC-SHA-256 key ID (1-65535) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 authentication hmac-sha-256 encrypted-password .. raw:: html M10-Smart RS420 :arg password: HMAC-SHA-256 encrypted password .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 authentication hmac-sha-256 password .. raw:: html M10-Smart RS420 HMAC-SHA-256 plain text password :arg txt: HMAC-SHA-256 plain text password (1-16) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 authentication md5 .. raw:: html M10-Smart RS420 MD5 authentication parameters :arg u32: MD5 key ID (1-65535) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 authentication md5 encrypted-password .. raw:: html M10-Smart RS420 :arg password: MD5 encrypted password .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 authentication md5 password .. raw:: html M10-Smart RS420 MD5 plain text password :arg txt: MD5 plain text password (1-16) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 cost .. raw:: html M10-Smart RS420 Interface cost :arg u32: OSPFv3 cost (1-65535) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 dead-interval .. raw:: html M10-Smart RS420 Interval after which neighbor is declared dead :arg u32: Neighbor dead interval in seconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 hello-interval .. raw:: html M10-Smart RS420 Interval between hello packets :arg u32: Interval between OSPFv3 hello packets in seconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 ifmtu .. raw:: html M10-Smart RS420 Interface MTU :arg u32: Interface MTU value (1-65535) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 instance-id .. raw:: html M10-Smart RS420 Instance identifier :arg u32: Instance ID (0-255) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 mtu-ignore .. raw:: html M10-Smart RS420 Disable Maximum Transmission Unit mismatch detection .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 network .. raw:: html M10-Smart RS420 Network type :arg broadcast: Broadcast network type :arg point-to-point: Point-to-point network type .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 passive .. raw:: html M10-Smart RS420 Disable forming of adjacency .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 priority .. raw:: html M10-Smart RS420 Router priority :arg u32: Priority (0-255) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 retransmit-interval .. raw:: html M10-Smart RS420 Interval between retransmitting lost link state advertisements :arg u32: Retransmit interval in seconds (3-65535) .. osdx:cfgcmd:: interfaces cellular ipv6 ospfv3 transmit-delay .. raw:: html M10-Smart RS420 Link state transmit delay :arg u32: Link state transmit delay in seconds (1-65535) .. osdx:cfgcmd:: interfaces cellular ipv6 ripng .. raw:: html M10-Smart RS420 Routing Information Protocol (RIPng) .. osdx:cfgcmd:: interfaces cellular ipv6 ripng split-horizon .. raw:: html M10-Smart RS420 Split horizon parameters .. osdx:cfgcmd:: interfaces cellular ipv6 ripng split-horizon disable .. raw:: html M10-Smart RS420 Disable split horizon .. osdx:cfgcmd:: interfaces cellular ipv6 ripng split-horizon poison-reverse .. raw:: html M10-Smart RS420 Enable poison reverse for split-horizon .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert .. raw:: html M10-Smart RS420 Configure parameters for sending Router Advertisements (RAs) .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert cur-hop-limit .. raw:: html M10-Smart RS420 Value to be placed in the Current Hop Limit field in RAs :arg u32: Value to place in the Current Hop Limit field in RAs (0-255) .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert default-lifetime .. raw:: html M10-Smart RS420 Value to be placed in Router Lifetime field in RAs :arg u32: Value in seconds to be placed in Router Lifetime field in RAs (4-9000) :arg u32: This means "not a default router", in Router Lifetime field (0) .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert default-preference .. raw:: html M10-Smart RS420 Default router preference :arg low: Default router is low preference :arg medium: Default router is medium preference :arg high: Default router is high preference .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert link-mtu .. raw:: html M10-Smart RS420 Value of link MTU to place in RAs :arg u32: Do not send MTU options in RAs (0) :arg u32: Value of link MTU to place in RAs (1280-2147483647) .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert managed-flag .. raw:: html M10-Smart RS420 :arg txt: Value for "managed address configuration" flag in RAs .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert max-interval .. raw:: html M10-Smart RS420 Maximum interval between unsolicited multicast RAs :arg u32: Maximum interval in seconds between unsolicited multicast RAs (4-1800) .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert min-interval .. raw:: html M10-Smart RS420 Minimum interval between unsolicited multicast RAs :arg u32: Minimum interval in seconds between unsolicited multicast RAs (3-1350) .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert name-server .. raw:: html M10-Smart RS420 :arg ipv6: IPv6 address of a Recursive DNS Server :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert other-config-flag .. raw:: html M10-Smart RS420 :arg txt: Value to be placed in the "other configuration" flag in RAs .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert prefix .. raw:: html M10-Smart RS420 IPv6 prefix to be advertised in Router Advertisements (RAs) :arg ipv6net: IPv6 prefix to be advertized in Router Advertisements (RAs) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert prefix autonomous-flag .. raw:: html M10-Smart RS420 :arg txt: Whether prefix can be used for address auto-configuration .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert prefix on-link-flag .. raw:: html M10-Smart RS420 :arg txt: Flag that prefix can be used for on-link determination .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert prefix preferred-lifetime .. raw:: html M10-Smart RS420 Time in seconds that the prefix will remain preferred :arg u32: Time in seconds that the prefix will remain preferred (0-2147483647) :arg infinity: Prefix will remain preferred forever .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert prefix valid-lifetime .. raw:: html M10-Smart RS420 Time in seconds that the prefix will remain valid :arg u32: Time in seconds that the prefix will remain valid (0-2147483647) :arg infinity: Prefix will remain valid forever .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert reachable-time .. raw:: html M10-Smart RS420 Value to be placed in "Reachable Time" field in RAs :arg u32: Reachable Time value in RAs (in milliseconds) (1-3600000) :arg u32: Reachable Time 0 (i.e., unspecified by this router) (0) .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert retrans-timer .. raw:: html M10-Smart RS420 Value to place in "Retrans Timer" field in RAs. :arg u32: Value in milliseconds to place in "Retrans Timer" field in RAs (0-2147483647) .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert send-advert .. raw:: html M10-Smart RS420 :arg txt: Enable/disable sending RAs .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert used-prefixes .. raw:: html M10-Smart RS420 Delegate prefixes used on the interface .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert used-prefixes autonomous-flag .. raw:: html M10-Smart RS420 :arg txt: Whether prefix can be used for address auto-configuration .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert used-prefixes on-link-flag .. raw:: html M10-Smart RS420 :arg txt: Flag that prefix can be used for on-link determination .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert used-prefixes preferred-lifetime .. raw:: html M10-Smart RS420 Time in seconds that the prefix will remain preferred :arg u32: Time in seconds that the prefix will remain preferred (0-2147483647) :arg infinity: Prefix will remain preferred forever .. osdx:cfgcmd:: interfaces cellular ipv6 router-advert used-prefixes valid-lifetime .. raw:: html M10-Smart RS420 Time in seconds that the prefix will remain valid :arg u32: Time in seconds that the prefix will remain valid (0-2147483647) :arg infinity: Prefix will remain valid forever .. osdx:cfgcmd:: interfaces cellular network .. raw:: html M10-Smart RS420 Configures network parameters for connection .. osdx:cfgcmd:: interfaces cellular network mode .. raw:: html M10-Smart RS420 Select the type of technology used when connecting to the cellular network :arg automatic: All modes are enabled :arg all-but-5g: All modes but 5G (SA/NSA) :arg all-but-5g-sa: All modes but 5G SA :arg 5g-nsa: LTE or LTE + 5G-NSA :arg 5g-sa: 5G SA only :arg cdma: CDMA (2G) only :arg gprs: GPRS (2G) only :arg hrpd: CDMA HRPD (3G) only :arg hybrid: CDMA Hybrid CDMA/HRPD :arg lte: LTE only :arg wcdma: UMTS/HSDPA (3G) only .. osdx:cfgcmd:: interfaces cellular pdp .. raw:: html M10-Smart RS420 Use multiple PDP contexts (APNs) over the same cellular radio interface :arg u32: PDP context index (1-4) :instances: Multiple :ref Required: cellular profile * .. osdx:cfgcmd:: interfaces cellular pdp address .. raw:: html M10-Smart RS420 IP address :arg ipv6cidr: IPv6 address and prefix length :arg dhcpv6: Dynamic Host Configuration Protocol for IPv6 :arg ipv4cidr: IPv4 address and prefix length :arg dhcp: Dynamic Host Configuration Protocol :instances: Multiple .. osdx:cfgcmd:: interfaces cellular pdp alarm .. raw:: html M10-Smart RS420 Enable or disable alarm according the link state .. osdx:cfgcmd:: interfaces cellular pdp alarm down .. raw:: html M10-Smart RS420 Alarm to be enabled if the link is down :ref Reference: system alarm * .. osdx:cfgcmd:: interfaces cellular pdp bridge-group .. raw:: html M10-Smart RS420 Add this interface to a bridge group :ref Required: interfaces bridge * .. osdx:cfgcmd:: interfaces cellular pdp bridge-group bridge .. raw:: html M10-Smart RS420 Bridge group name (br[0-9]+) :ref Reference: interfaces bridge * .. osdx:cfgcmd:: interfaces cellular pdp bridge-group isolate .. raw:: html M10-Smart RS420 Isolate port .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp .. raw:: html M10-Smart RS420 Bridge port Spanning Tree Protocol configuration .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp admin-edge .. raw:: html M10-Smart RS420 Enable the admin edge state .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp bpdu-filter .. raw:: html M10-Smart RS420 Enable the BPDU filter capability If enabled, this port will discard any ingress BPDUs and will not issue any BPUs .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp bpdu-guard .. raw:: html M10-Smart RS420 Enable the bpduguard configuration .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp cost .. raw:: html M10-Smart RS420 Bridge port cost :arg u32: Auto (0) :arg u32: Bridge port cost (1-65535) .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp disable-auto-edge .. raw:: html M10-Smart RS420 Enable the auto transition to/from edge state .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp network-assurance .. raw:: html M10-Smart RS420 Enable the bridge assurance capability .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp p2p .. raw:: html M10-Smart RS420 :arg txt: Enable Point-2-Point (P2P) detection mode .. osdx:cfgcmd:: interfaces cellular pdp bridge-group stp priority .. raw:: html M10-Smart RS420 Bridge port priority :arg u32: Bridge port priority (0-15) .. osdx:cfgcmd:: interfaces cellular pdp bridge-group vlan .. raw:: html M10-Smart RS420 Enable VLAN in this bridge port :arg u32: VLAN ID (1-4094) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular pdp bridge-group vlan pvid .. raw:: html M10-Smart RS420 This VLAN specified is to be considered a PVID at ingress Any untagged frames will be assigned to this VLAN .. osdx:cfgcmd:: interfaces cellular pdp bridge-group vlan untagged .. raw:: html M10-Smart RS420 This VLAN is to be treated as untagged on egress The bridge will always remove the VLAN tag from egress packets .. osdx:cfgcmd:: interfaces cellular pdp description .. raw:: html M10-Smart RS420 Description :arg id: "Interface description is too long (limit 256 characters)" (1-256) .. osdx:cfgcmd:: interfaces cellular pdp dhcp .. raw:: html M10-Smart RS420 Dynamic Host Configuration Protocol configuration .. osdx:cfgcmd:: interfaces cellular pdp dhcp client .. raw:: html M10-Smart RS420 DHCP client configuration .. osdx:cfgcmd:: interfaces cellular pdp dhcp client fallback .. raw:: html M10-Smart RS420 :arg ipv4cidr: Fallback IP address :arg ipv6cidr: Fallback IP address .. osdx:cfgcmd:: interfaces cellular pdp dhcp client rfc3442-routes .. raw:: html M10-Smart RS420 Install RFC3442 routes received from DHCP server .. osdx:cfgcmd:: interfaces cellular pdp dhcp client send .. raw:: html M10-Smart RS420 Send user-defined options to the DHCP server .. osdx:cfgcmd:: interfaces cellular pdp dhcp client send dhcp-client-identifier .. raw:: html M10-Smart RS420 Include the 'dhcp-client-identifier' option :instances: Unique .. osdx:cfgcmd:: interfaces cellular pdp dhcp client send dhcp-client-identifier base-mac .. raw:: html M10-Smart RS420 Use device base mac as identifier .. osdx:cfgcmd:: interfaces cellular pdp dhcp client send dhcp-client-identifier serial-number .. raw:: html M10-Smart RS420 Use device serial number as identifier .. osdx:cfgcmd:: interfaces cellular pdp dhcp client send dhcp-client-identifier string .. raw:: html M10-Smart RS420 Use a string as identifier :arg id: Identifier string (1-255) .. osdx:cfgcmd:: interfaces cellular pdp dhcp client send vendor-class-identifier .. raw:: html M10-Smart RS420 Include the 'vendor-class-identifier' option :instances: Unique .. osdx:cfgcmd:: interfaces cellular pdp dhcp client send vendor-class-identifier string .. raw:: html M10-Smart RS420 Use a string as identifier :arg id: Identifier string (1-255) .. osdx:cfgcmd:: interfaces cellular pdp dhcpv6 .. raw:: html M10-Smart RS420 Dynamic Host Configuration Protocol v6 configuration .. osdx:cfgcmd:: interfaces cellular pdp dhcpv6 client .. raw:: html M10-Smart RS420 DHCPv6 client configuration .. osdx:cfgcmd:: interfaces cellular pdp dhcpv6 client parameters-only .. raw:: html M10-Smart RS420 Acquire only config parameters, not address .. osdx:cfgcmd:: interfaces cellular pdp dhcpv6 client send .. raw:: html M10-Smart RS420 Send user-defined options to the DHCPv6 server .. osdx:cfgcmd:: interfaces cellular pdp dhcpv6 client send duid .. raw:: html M10-Smart RS420 :arg id: DHCPv6 DUID to be sent by dhcpv6 client .. osdx:cfgcmd:: interfaces cellular pdp dhcpv6 client temporary .. raw:: html M10-Smart RS420 IPv6 "temporary" address .. osdx:cfgcmd:: interfaces cellular pdp disable .. raw:: html M10-Smart RS420 Disable interface .. osdx:cfgcmd:: interfaces cellular pdp disable advisor .. raw:: html M10-Smart RS420 Advisor to enable or disable the interface :ref Reference: system advisor * .. osdx:cfgcmd:: interfaces cellular pdp flow .. raw:: html M10-Smart RS420 Active netflow on interface .. osdx:cfgcmd:: interfaces cellular pdp flow egress .. raw:: html M10-Smart RS420 Active output traffic .. osdx:cfgcmd:: interfaces cellular pdp flow egress selector .. raw:: html M10-Smart RS420 Traffic selector :ref Reference: traffic selector * .. osdx:cfgcmd:: interfaces cellular pdp flow ingress .. raw:: html M10-Smart RS420 Active input traffic .. osdx:cfgcmd:: interfaces cellular pdp flow ingress selector .. raw:: html M10-Smart RS420 Traffic selector :ref Reference: traffic selector * .. osdx:cfgcmd:: interfaces cellular pdp ip .. raw:: html M10-Smart RS420 IPv4 routing parameters .. osdx:cfgcmd:: interfaces cellular pdp ip igmp .. raw:: html M10-Smart RS420 Internet Group Management Protocol (IGMP) parameters .. osdx:cfgcmd:: interfaces cellular pdp ip igmp join .. raw:: html M10-Smart RS420 Join multicast group :arg ipv4: Join multicast group on this interface .. osdx:cfgcmd:: interfaces cellular pdp ip igmp last-member-query-count .. raw:: html M10-Smart RS420 IGMP last member query count :arg u32: IGMP last member query count (1-255) .. osdx:cfgcmd:: interfaces cellular pdp ip igmp last-member-query-interval .. raw:: html M10-Smart RS420 IGMP last member query interval :arg u32: IGMP last member query interval in deciseconds (1-65535) .. osdx:cfgcmd:: interfaces cellular pdp ip igmp query-interval .. raw:: html M10-Smart RS420 IGMP query interval :arg u32: IGMP query interval in seconds (1-65535) .. osdx:cfgcmd:: interfaces cellular pdp ip igmp query-max-response-time .. raw:: html M10-Smart RS420 IGMP query response timeout value :arg u32: IGMP query response timeout value in deciseconds (1-65535) .. osdx:cfgcmd:: interfaces cellular pdp ip igmp version .. raw:: html M10-Smart RS420 IGMP version :arg u32: IGMP version used on this interface (2-3) .. osdx:cfgcmd:: interfaces cellular pdp ip multicast .. raw:: html M10-Smart RS420 Multicast parameters .. osdx:cfgcmd:: interfaces cellular pdp ip multicast boundary-list .. raw:: html M10-Smart RS420 Prefix-list to control for which groups to accept or ignore received PIM join or IGMP report messages :ref Reference: protocols ip prefix-list * .. osdx:cfgcmd:: interfaces cellular pdp ip ospf .. raw:: html M10-Smart RS420 Open Shortest Path First (OSPF) parameters .. osdx:cfgcmd:: interfaces cellular pdp ip ospf authentication .. raw:: html M10-Smart RS420 OSPF interface authentication .. osdx:cfgcmd:: interfaces cellular pdp ip ospf authentication encrypted-password .. raw:: html M10-Smart RS420 :arg password: Encrypted password .. osdx:cfgcmd:: interfaces cellular pdp ip ospf authentication message-digest .. raw:: html M10-Smart RS420 MD5 authentication parameters :arg id: MD5 ID number (1-255) :instances: Multiple .. osdx:cfgcmd:: interfaces cellular pdp ip ospf authentication message-digest encrypted-password .. raw:: html M10-Smart RS420 :arg password: MD5 encrypted key .. osdx:cfgcmd:: interfaces cellular pdp ip ospf authentication message-digest password .. raw:: html M10-Smart RS420 MD5 key :arg txt: MD5 Key (1-16) .. osdx:cfgcmd:: interfaces cellular pdp ip ospf authentication password .. raw:: html M10-Smart RS420 :arg txt: Plain text password .. osdx:cfgcmd:: interfaces cellular pdp