Bonding
These scenarios cover some aspects related to link-aggregation, which is the technique of combining multiple network connections in parallel in order to increase throughput, to provide redundancy or both. On OSDx, this can be achieved by using bonding interfaces.
Test Round-Robin Mode
Description
A bonding interface is configured in DUT0 using the round-robin mode. This mode can be used to achieve load-balancing.
Scenario
Step 1: Set the following configuration in DUT0:
set interfaces bonding bond0 address 192.168.100.10/24 set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 mode round-robin set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT1:
set interfaces ethernet eth0 address 192.168.100.20/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c01/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: load balancing (round-robin)Show output
Ethernet Channel Bonding Driver: v6.1.90 Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 2 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.332 ms 64 bytes from 192.168.100.20: icmp_seq=2 ttl=64 time=0.403 ms --- 192.168.100.20 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1003ms rtt min/avg/max/mdev = 0.332/0.367/0.403/0.035 ms
Step 6: Run command interfaces ethernet clear at DUT0.
Step 7: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 47848 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 445 MBytes 3.73 Gbits/sec 946 919 KBytes [ 5] 1.00-2.00 sec 459 MBytes 3.85 Gbits/sec 748 1.09 MBytes [ 5] 2.00-3.00 sec 491 MBytes 4.12 Gbits/sec 426 1.30 MBytes [ 5] 3.00-4.00 sec 472 MBytes 3.96 Gbits/sec 51 1.43 MBytes [ 5] 4.00-5.00 sec 476 MBytes 4.00 Gbits/sec 140 1.52 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 2.29 GBytes 3.93 Gbits/sec 2311 sender [ 5] 0.00-5.00 sec 2.29 GBytes 3.93 Gbits/sec receiver iperf Done.
Step 8: Run command interfaces ethernet show counters at DUT0 and check if output matches the following regular expressions:
eth0\s+up\s+\d+\s+\d+\s+0\s+\d{2,} eth1\s+up\s+\d+\s+\d+\s+0\s+\d{2,}Show output
------------------------------------------------------------------------------ Name Oper Rx Packets Rx Bytes Rx Errors Tx Packets Tx Bytes Tx Errors ------------------------------------------------------------------------------ eth0 up 189794 15779009 0 849923 1286762996 0 eth1 up 204710 17159339 0 849835 1286630016 0
Test Active-Backup Mode
Description
A bonding interface is configured in DUT0 using the active-backup mode. This mode can be used to achieve a higher degree of fault-tolerance.
Scenario
Step 1: Set the following configuration in DUT0:
set interfaces bonding bond0 address 192.168.100.10/24 set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 mode active-backup set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT1:
set interfaces ethernet eth0 address 192.168.100.20/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c01/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: fault-tolerance (active-backup)Show output
Ethernet Channel Bonding Driver: v6.1.90 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 2 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.293 ms 64 bytes from 192.168.100.20: icmp_seq=2 ttl=64 time=0.203 ms --- 192.168.100.20 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1004ms rtt min/avg/max/mdev = 0.203/0.248/0.293/0.045 ms
Step 6: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 54666 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 467 MBytes 3.92 Gbits/sec 239 1.23 MBytes [ 5] 1.00-2.00 sec 424 MBytes 3.55 Gbits/sec 0 1.34 MBytes [ 5] 2.00-3.00 sec 470 MBytes 3.94 Gbits/sec 0 1.46 MBytes [ 5] 3.00-4.00 sec 479 MBytes 4.02 Gbits/sec 0 1.54 MBytes [ 5] 4.00-5.00 sec 472 MBytes 3.96 Gbits/sec 0 1.63 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 2.26 GBytes 3.88 Gbits/sec 239 sender [ 5] 0.00-5.00 sec 2.26 GBytes 3.87 Gbits/sec receiver iperf Done.
Step 7: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth0Show output
Ethernet Channel Bonding Driver: v6.1.90 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 8: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 57244 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 494 MBytes 4.14 Gbits/sec 439 1.34 MBytes [ 5] 1.00-2.00 sec 496 MBytes 4.16 Gbits/sec 0 1.49 MBytes [ 5] 2.00-3.00 sec 499 MBytes 4.18 Gbits/sec 0 1.58 MBytes [ 5] 3.00-4.00 sec 521 MBytes 4.37 Gbits/sec 0 1.67 MBytes [ 5] 4.00-5.00 sec 430 MBytes 3.61 Gbits/sec 12 1.20 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 2.38 GBytes 4.09 Gbits/sec 451 sender [ 5] 0.00-5.00 sec 2.38 GBytes 4.09 Gbits/sec receiver iperf Done.
Step 9: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth1Show output
Ethernet Channel Bonding Driver: v6.1.90 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0