Site-To-Site

This scenario shows how to configure and connect two subnets with each other through a VPN tunnel and automatically configure the negotiated remote prefixes as routes. DUT0 acts as a responder and DUT1 as a initiator.

../../../../../../../_images/sitetosite3.svg

Test Site-To-Site With Basic Route Installation

Description

In this scenario, both devices install routes for the VPN traffic in the main table.

Scenario

Step 1: Run command protocols ip show route at DUT0 and check if output does not contain the following tokens:

K>* 10.3.0.0/24

Step 2: Set the following configuration in DUT0:

set interfaces dummy dum0 address 10.1.0.1/24
set interfaces ethernet eth0 address 80.0.0.1/24
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf main
set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1/uOnA5RNvqkMQL7jPFsmaSQjh+BRewym0=
set vpn ipsec esp-group CHILD-SA mode tunnel
set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128
set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19
set vpn ipsec ike-group IKE-SA key-exchange ikev2
set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19
set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128
set vpn ipsec ike-group IKE-SA proposal 1 hash sha256
set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA
set vpn ipsec site-to-site peer PEER connection-type respond
set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA
set vpn ipsec site-to-site peer PEER ike-group IKE-SA
set vpn ipsec site-to-site peer PEER local-address 80.0.0.1
set vpn ipsec site-to-site peer PEER remote-address 80.0.0.2
set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main
set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24
set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24

Step 3: Set the following configuration in DUT1:

set interfaces dummy dum0 address 10.3.0.1/24
set interfaces ethernet eth0 address 80.0.0.2/24
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf main
set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX18QlnNfrjSPxuHaz1ZMr9wwPpGZ/vrKZz4=
set vpn ipsec esp-group CHILD-SA mode tunnel
set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128
set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19
set vpn ipsec ike-group IKE-SA key-exchange ikev2
set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19
set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128
set vpn ipsec ike-group IKE-SA proposal 1 hash sha256
set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA
set vpn ipsec site-to-site peer PEER connection-type initiate
set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA
set vpn ipsec site-to-site peer PEER ike-group IKE-SA
set vpn ipsec site-to-site peer PEER local-address 80.0.0.2
set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1
set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main
set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24
set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24

Step 4: Ping IP address 80.0.0.1 from DUT1:

admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1
Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data.
64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.289 ms

--- 80.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.289/0.289/0.289/0.000 ms

Step 5: Ping IP address 80.0.0.2 from DUT0:

admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1
Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data.
64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=9.93 ms

--- 80.0.0.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 9.927/9.927/9.927/0.000 ms

Step 6: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:

peer-PEER-tunnel-\d+.+INSTALLED
Show output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, ec67cffdf4287fdd_i b9b1011682cb9839_r*
  local  '80.0.0.1' @ 80.0.0.1[500]
  remote '80.0.0.2' @ 80.0.0.2[500]
  AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256
  established 0s ago, rekeying in 15908s
  peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256
    installed 0s ago, rekeying in 3292s, expires in 3960s
    in  c5bf5ecd,      0 bytes,     0 packets
    out cd86a02f,      0 bytes,     0 packets
    local  10.1.0.0/24
    remote 10.3.0.0/24

Step 7: Run command protocols ip show route at DUT0 and check if output contains the following tokens:

K>* 10.3.0.0/24
Show output
Codes: K - kernel route, C - connected, S - static, R - RIP,
       O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
       T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR,
       f - OpenFabric,
       > - selected route, * - FIB route, q - queued, r - rejected, b - backup
       t - trapped, o - offload failure

C>* 10.1.0.0/24 is directly connected, dum0, 00:00:07
K>* 10.3.0.0/24 [0/0] via 80.0.0.2, eth0, 00:00:01
C>* 80.0.0.0/24 is directly connected, eth0, 00:00:07

Step 8: Ping IP address 10.1.0.1 from DUT1:

admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1
Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data.
64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.352 ms

--- 10.1.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.352/0.352/0.352/0.000 ms

Step 9: Initiate a tcp connection from DUT1 to DUT0 and try to send some messages between both endpoints

admin@DUT0$ monitor test connection server 8080 tcp
admin@DUT1$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1

Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:

[1-9]\d? packets
Show output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, ec67cffdf4287fdd_i b9b1011682cb9839_r*
  local  '80.0.0.1' @ 80.0.0.1[500]
  remote '80.0.0.2' @ 80.0.0.2[500]
  AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256
  established 4s ago, rekeying in 15904s
  peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256
    installed 4s ago, rekeying in 3288s, expires in 3956s
    in  c5bf5ecd,    920 bytes,    15 packets,     0s ago
    out cd86a02f,    868 bytes,    14 packets,     0s ago
    local  10.1.0.0/24
    remote 10.3.0.0/24

Test Site-To-Site With VRF Route Installation

Description

In this scenario, DUT0 install reoutes in a separate VRF called LAN.

Scenario

Step 1: Run command protocols vrf LAN ip show route at DUT0 and check if output does not contain the following tokens:

K>* 10.3.0.0/24
Show output
% VRF LAN not found

Step 2: Set the following configuration in DUT0:

set interfaces dummy dum0 address 10.1.0.1/24
set interfaces dummy dum0 vrf LAN
set interfaces ethernet eth0 address 80.0.0.1/24
set interfaces ethernet eth0 vrf WAN
set protocols vrf WAN static route 10.1.0.0/24 next-hop-vrf LAN
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf LAN
set system vrf WAN
set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19Lw9KkbHqRwuI0ZQ+eTRdpFPzPVQ+oq70=
set vpn ipsec esp-group CHILD-SA mode tunnel
set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128
set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19
set vpn ipsec ike-group IKE-SA key-exchange ikev2
set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19
set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128
set vpn ipsec ike-group IKE-SA proposal 1 hash sha256
set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA
set vpn ipsec site-to-site peer PEER connection-type respond
set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA
set vpn ipsec site-to-site peer PEER ike-group IKE-SA
set vpn ipsec site-to-site peer PEER local-address 80.0.0.1
set vpn ipsec site-to-site peer PEER remote-address 80.0.0.2
set vpn ipsec site-to-site peer PEER tunnel 1 install-routes LAN
set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24
set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24

Step 3: Set the following configuration in DUT1:

set interfaces dummy dum0 address 10.3.0.1/24
set interfaces ethernet eth0 address 80.0.0.2/24
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf main
set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19aTSmyjIjk8XyrnsQ5QlP4tajrT/Ahd1M=
set vpn ipsec esp-group CHILD-SA mode tunnel
set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128
set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19
set vpn ipsec ike-group IKE-SA key-exchange ikev2
set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19
set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128
set vpn ipsec ike-group IKE-SA proposal 1 hash sha256
set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA
set vpn ipsec site-to-site peer PEER connection-type initiate
set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA
set vpn ipsec site-to-site peer PEER ike-group IKE-SA
set vpn ipsec site-to-site peer PEER local-address 80.0.0.2
set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1
set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main
set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24
set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24

Step 4: Ping IP address 80.0.0.1 from DUT1:

admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1
Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data.
64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.414 ms

--- 80.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.414/0.414/0.414/0.000 ms

Step 5: Ping IP address 80.0.0.2 from DUT0:

admin@DUT0$ ping 80.0.0.2 vrf WAN count 1 size 56 timeout 1
Show output
ping: Warning: source address might be selected on device other than: WAN
PING 80.0.0.2 (80.0.0.2) from 80.0.0.1 WAN: 56(84) bytes of data.
64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=1.80 ms

--- 80.0.0.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 1.797/1.797/1.797/0.000 ms

Step 6: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:

peer-PEER-tunnel-\d+.+INSTALLED
Show output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 8c5e2f72ae17426a_i 685858093415eb42_r*
  local  '80.0.0.1' @ 80.0.0.1[500]
  remote '80.0.0.2' @ 80.0.0.2[500]
  AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256
  established 1s ago, rekeying in 24676s
  peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256
    installed 1s ago, rekeying in 3274s, expires in 3959s
    in  c1a42e7f,      0 bytes,     0 packets
    out c2554b28,      0 bytes,     0 packets
    local  10.1.0.0/24
    remote 10.3.0.0/24

Step 7: Run command protocols vrf LAN ip show route at DUT0 and check if output contains the following tokens:

K>* 10.3.0.0/24
Show output
Codes: K - kernel route, C - connected, S - static, R - RIP,
       O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
       T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR,
       f - OpenFabric,
       > - selected route, * - FIB route, q - queued, r - rejected, b - backup
       t - trapped, o - offload failure

VRF LAN:
K>* 0.0.0.0/0 [255/8192] unreachable (ICMP unreachable), 00:00:07
C>* 10.1.0.0/24 is directly connected, dum0, 00:00:07
K>* 10.3.0.0/24 [0/0] via 80.0.0.2, eth0 (vrf WAN), 00:00:01

Step 8: Ping IP address 10.1.0.1 from DUT1:

admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1
Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data.
64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.347 ms

--- 10.1.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.347/0.347/0.347/0.000 ms

Step 9: Initiate a tcp connection from DUT1 to DUT0 and try to send some messages between both endpoints

admin@DUT0$ monitor test connection server 8080 tcp vrf LAN
admin@DUT1$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1

Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:

[1-9]\d? packets
Show output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 8c5e2f72ae17426a_i 685858093415eb42_r*
  local  '80.0.0.1' @ 80.0.0.1[500]
  remote '80.0.0.2' @ 80.0.0.2[500]
  AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256
  established 4s ago, rekeying in 24673s
  peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256
    installed 4s ago, rekeying in 3271s, expires in 3956s
    in  c1a42e7f,    920 bytes,    15 packets,     0s ago
    out c2554b28,    868 bytes,    14 packets,     0s ago
    local  10.1.0.0/24
    remote 10.3.0.0/24