Basic

Contents

The following scenario shows how to configure a HTB qdisc.

Test HTB QDisc

Description

In this scenario, a Hierarchy Token Bucket (HTB) qdisc is configured in DUT0 (‘eth0’ interface) to achieve linksharing among a hierarchy of classes. Three classes are created with different matches (filters). Each match is allocated to a single class and evaluated in order.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 10.0.0.2/24
set interfaces ethernet eth0 traffic control out QDISC
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set traffic control QDISC type htb bandwidth 100
set traffic control QDISC type htb class 1 bandwidth percentage 50
set traffic control QDISC type htb class 1 ceiling percentage 100
set traffic control QDISC type htb class 2 bandwidth percentage 20
set traffic control QDISC type htb class 2 ceiling percentage 0
set traffic control QDISC type htb class 3 bandwidth percentage 10
set traffic control QDISC type htb class 3 ceiling percentage 0
set traffic control QDISC type htb default-class 3
set traffic control QDISC type htb match 1 class 1
set traffic control QDISC type htb match 1 ip destination port 8080
set traffic control QDISC type htb match 2 class 2
set traffic control QDISC type htb match 2 ip protocol tcp

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 10.0.0.1/24
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Ping the IP address 10.0.0.1 from DUT0:

admin@DUT0$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=1.72 ms

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 1.716/1.716/1.716/0.000 ms

Step 4: Initiate a bandwidth test from DUT0 to DUT1

admin@DUT1$ monitor test performance server port 8080
admin@DUT0$ monitor test performance client 10.0.0.1 duration 5 port 8080 parallel 1

Expect the following output on DUT0:

Connecting to host 10.0.0.1, port 8080
[  5] local 10.0.0.2 port 47180 connected to 10.0.0.1 port 8080
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  14.0 MBytes   117 Mbits/sec  172   70.7 KBytes
[  5]   1.00-2.00   sec  11.5 MBytes  96.4 Mbits/sec   57   72.1 KBytes
[  5]   2.00-3.00   sec  11.6 MBytes  97.0 Mbits/sec   54    106 KBytes
[  5]   3.00-4.00   sec  11.1 MBytes  92.8 Mbits/sec   94   79.2 KBytes
[  5]   4.00-5.00   sec  11.4 MBytes  95.9 Mbits/sec   74   86.3 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-5.00   sec  59.5 MBytes  99.9 Mbits/sec  451             sender
[  5]   0.00-5.00   sec  58.5 MBytes  98.0 Mbits/sec                  receiver

iperf Done.

Step 5: Initiate a bandwidth test from DUT0 to DUT1

admin@DUT1$ monitor test performance server port 1234
admin@DUT0$ monitor test performance client 10.0.0.1 duration 5 port 1234 parallel 1

Expect the following output on DUT0:

Connecting to host 10.0.0.1, port 1234
[  5] local 10.0.0.2 port 53124 connected to 10.0.0.1 port 1234
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  2.53 MBytes  21.2 Mbits/sec   52   22.6 KBytes
[  5]   1.00-2.00   sec  2.24 MBytes  18.8 Mbits/sec   61   15.6 KBytes
[  5]   2.00-3.00   sec  2.24 MBytes  18.8 Mbits/sec   56   21.2 KBytes
[  5]   3.00-4.00   sec  2.24 MBytes  18.8 Mbits/sec   53   17.0 KBytes
[  5]   4.00-5.00   sec  2.36 MBytes  19.8 Mbits/sec   54   25.5 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-5.00   sec  11.6 MBytes  19.5 Mbits/sec  276             sender
[  5]   0.00-5.00   sec  11.3 MBytes  19.0 Mbits/sec                  receiver

iperf Done.

Step 6: Run the command traffic control show on DUT0 and check whether the output contains the following tokens:

class 1
class 2
class 3 (default)

Show output

Traffic control for interface 'eth0' - 'egress' mode

------------------------------------------------------------------------------------
ID   traffic control        type         parent  bytes sent  pkts sent  pkts dropped
------------------------------------------------------------------------------------
1:0  QDISC            htb                root      76605242      50641            53
1:1  QDISC            class 1            1:0       64178623      42407             0
1:2  QDISC            class 2            1:0       12425633       8225             0
1:3  QDISC            class 3 (default)  1:0            986          9             0
2:0  -                htb                1:1       64178623      42407            17
3:0  -                htb                1:2       12425633       8225            36
4:0  -                htb                1:3            986          9             0

Attention

The previous command output should include packets for the different HTB classes. If not, obtaining debugging information may prove usuful. This can be achieved by setting the following configuration commands: set traffic control <NAME> type htb match 1 log <PREFIX> or set traffic policy <NAME> rule 1 log prefix <PREFIX>. After generating some traffic, the system journal monitor command can be used to review log messages.

---