Bonding
These scenarios cover some aspects related to link-aggregation, which is the technique of combining multiple network connections in parallel in order to increase throughput, to provide redundancy or both. On OSDx, this can be achieved by using bonding interfaces.
Test Round-Robin Mode
Description
A bonding interface is configured in DUT0 using the round-robin mode. This mode can be used to achieve load-balancing.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces bonding bond0 address 192.168.100.10/24 set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 mode round-robin set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.20/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c01/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: load balancing (round-robin)Show output
Ethernet Channel Bonding Driver: v6.1.119 Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 2 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.515 ms 64 bytes from 192.168.100.20: icmp_seq=2 ttl=64 time=0.372 ms --- 192.168.100.20 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1015ms rtt min/avg/max/mdev = 0.372/0.443/0.515/0.071 ms
Step 6: Run command interfaces ethernet clear at DUT0.
Step 7: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 53726 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 119 MBytes 995 Mbits/sec 130 451 KBytes [ 5] 1.00-2.00 sec 117 MBytes 983 Mbits/sec 57 576 KBytes [ 5] 2.00-3.00 sec 124 MBytes 1.04 Gbits/sec 45 672 KBytes [ 5] 3.00-4.00 sec 128 MBytes 1.07 Gbits/sec 83 755 KBytes [ 5] 4.00-5.00 sec 111 MBytes 933 Mbits/sec 8 813 KBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 598 MBytes 1.00 Gbits/sec 323 sender [ 5] 0.00-5.00 sec 595 MBytes 998 Mbits/sec receiver iperf Done.
Step 8: Run command interfaces ethernet show counters at DUT0 and check if output matches the following regular expressions:
eth0\s+up\s+\d+\s+\d+\s+0\s+\d{2,} eth1\s+up\s+\d+\s+\d+\s+0\s+\d{2,}Show output
----------------------------------------------------------------------------- Name Oper Rx Packets Rx Bytes Rx Errors Tx Packets Tx Bytes Tx Errors ----------------------------------------------------------------------------- eth0 up 39825 3054807 0 216497 327756880 0 eth1 up 68541 5298142 0 215502 326246014 0
Test Active-Backup Mode
Description
A bonding interface is configured in DUT0 using the active-backup mode. This mode can be used to achieve a higher degree of fault-tolerance.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces bonding bond0 address 192.168.100.10/24 set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 mode active-backup set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.20/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c01/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: fault-tolerance (active-backup)Show output
Ethernet Channel Bonding Driver: v6.1.119 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 2 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=1.34 ms 64 bytes from 192.168.100.20: icmp_seq=2 ttl=64 time=0.326 ms --- 192.168.100.20 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.326/0.832/1.339/0.506 ms
Step 6: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 49864 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 124 MBytes 1.04 Gbits/sec 116 1.46 MBytes [ 5] 1.00-2.00 sec 124 MBytes 1.04 Gbits/sec 0 1.60 MBytes [ 5] 2.00-3.00 sec 150 MBytes 1.26 Gbits/sec 91 1.20 MBytes [ 5] 3.00-4.00 sec 150 MBytes 1.26 Gbits/sec 0 1.26 MBytes [ 5] 4.00-5.00 sec 135 MBytes 1.13 Gbits/sec 0 1.31 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 683 MBytes 1.15 Gbits/sec 207 sender [ 5] 0.00-5.00 sec 680 MBytes 1.14 Gbits/sec receiver iperf Done.
Step 7: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth0Show output
Ethernet Channel Bonding Driver: v6.1.119 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 8: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 48978 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 158 MBytes 1.33 Gbits/sec 44 1.37 MBytes [ 5] 1.00-2.00 sec 161 MBytes 1.35 Gbits/sec 20 1.04 MBytes [ 5] 2.00-3.00 sec 175 MBytes 1.47 Gbits/sec 0 1.10 MBytes [ 5] 3.00-4.00 sec 181 MBytes 1.52 Gbits/sec 0 1.14 MBytes [ 5] 4.00-5.00 sec 162 MBytes 1.36 Gbits/sec 0 1.18 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 838 MBytes 1.41 Gbits/sec 64 sender [ 5] 0.00-5.00 sec 836 MBytes 1.40 Gbits/sec receiver iperf Done.
Step 9: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth1Show output
Ethernet Channel Bonding Driver: v6.1.119 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0