Vrrp
Examples for High Availability (VRRP)
VRRP With MD5 Authentication
Description
This scenario checks that two OSDx devices can use VRRP with MD5 authentication.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX1856TAQBml5CKLICFHTp2iQ6DnChsUWrgE= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type md5 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Run command system vrrp show at DUT0 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:02 none
Step 3: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX1/hJH2JuftIzn537TgpEN+n1ouh+CS6ePg= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type md5 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Run command system vrrp show at DUT1 and check if output contains the following tokens:
BACKUPShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:01 none
Step 5: Run command system vrrp show detail at DUT0 and check if output matches the following regular expressions:
MD5Show output
Interface: eth0 Group: 1 State: MASTER Last Transition: 0:00:04 Priority: 200 Advertisement interval: 1 sec Authentication type: MD5 Preempt: disabled Sync-group: none VIP count: 1 192.168.10.1
Step 6: Run command system vrrp show detail at DUT1 and check if output matches the following regular expressions:
MD5Show output
Interface: eth0 Group: 1 State: BACKUP Last Transition: 0:00:01 Master router: ff02::12 Master priority: 0 Priority: 100 Advertisement interval: 1 sec Authentication type: MD5 Preempt: disabled Sync-group: none VIP count: 1 192.168.10.1
Step 7: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX1856TAQBml5CKLICFHTp2iQ6DnChsUWrgE= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type md5 set interfaces ethernet eth0 vrrp vrrp-group 1 disable set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 8: Run command system vrrp show at DUT0 and check if output contains the following tokens:
BACKUPShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:00 none
Step 9: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
VRRP With Plaintext Password Authentication
Description
This scenario checks that two OSDx devices can use VRRP with plaintext-password authentication.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX1/BFTBbbIkTW0Qt9hUlHwIoDCQ4WLk7wk4= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type plaintext-password set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Run command system vrrp show at DUT0 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:02 none
Step 3: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX1/x8kaFR7xDtU1bdSm0GLhVRNDNe+TaJHA= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type plaintext-password set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Run command system vrrp show at DUT1 and check if output contains the following tokens:
BACKUPShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:00 none
Step 5: Run command system vrrp show detail at DUT0 and check if output matches the following regular expressions:
SIMPLE_PASSWORDShow output
Interface: eth0 Group: 1 State: MASTER Last Transition: 0:00:04 Priority: 200 Advertisement interval: 1 sec Authentication type: SIMPLE_PASSWORD Preempt: disabled Sync-group: none VIP count: 1 192.168.10.1
Step 6: Run command system vrrp show detail at DUT1 and check if output matches the following regular expressions:
SIMPLE_PASSWORDShow output
Interface: eth0 Group: 1 State: BACKUP Last Transition: 0:00:01 Master router: ff02::12 Master priority: 0 Priority: 100 Advertisement interval: 1 sec Authentication type: SIMPLE_PASSWORD Preempt: disabled Sync-group: none VIP count: 1 192.168.10.1
Step 7: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX1/BFTBbbIkTW0Qt9hUlHwIoDCQ4WLk7wk4= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type plaintext-password set interfaces ethernet eth0 vrrp vrrp-group 1 disable set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 8: Run command system vrrp show at DUT0 and check if output contains the following tokens:
BACKUPShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:00 none
Step 9: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
VRRP With AH Authentication
Description
This scenario checks that two OSDx devices can use VRRP with AH authentication.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX1804+QppbP7WqklZLGc0a+E+ClAHf2r9cU= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type ah set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Run command system vrrp show at DUT0 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 3: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX18673jiMbY36N3kmZDW5xuHdGWWin8RrIk= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type ah set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Run command system vrrp show at DUT1 and check if output contains the following tokens:
BACKUPShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:00 none
Step 5: Run command system vrrp show detail at DUT0 and check if output matches the following regular expressions:
IPSEC_AHShow output
Interface: eth0 Group: 1 State: MASTER Last Transition: 0:00:04 Priority: 200 Advertisement interval: 1 sec Authentication type: IPSEC_AH Preempt: disabled Sync-group: none VIP count: 1 192.168.10.1
Step 6: Run command system vrrp show detail at DUT1 and check if output matches the following regular expressions:
IPSEC_AHShow output
Interface: eth0 Group: 1 State: BACKUP Last Transition: 0:00:01 Master router: 192.168.100.100 Master priority: 200 Priority: 100 Advertisement interval: 1 sec Authentication type: IPSEC_AH Preempt: disabled Sync-group: none VIP count: 1 192.168.10.1
Step 7: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 authentication encrypted-password U2FsdGVkX1804+QppbP7WqklZLGc0a+E+ClAHf2r9cU= set interfaces ethernet eth0 vrrp vrrp-group 1 authentication type ah set interfaces ethernet eth0 vrrp vrrp-group 1 disable set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 8: Run command system vrrp show at DUT0 and check if output contains the following tokens:
BACKUPShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:00 none
Step 9: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
VRRP RFC3768 Compatibility Configuration
Description
Check that a virtual interface is being created when this option is configured.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 rfc3768-compatibility set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Run command interfaces show at DUT0 and check if output matches the following regular expressions:
eth0v1\s*192.168.10.1/32Show output
------------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------- eth0 192.168.100.100/24 up up fe80::dcad:beff:feef:6c00/64 eth0v1 192.168.10.1/32 up up eth1 down down
Two VRRP Devices In Same Sync Group
Description
Configure 2 DUTs in the same sync-group to check that they do communicate between each other.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 sync-group MAIN0 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp sync-group MAIN0
Step 2: Run command system vrrp show at DUT0 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:02 MAIN0
Step 3: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 sync-group MAIN1 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp sync-group MAIN1
Step 4: Run command system vrrp show at DUT1 and check if output contains the following tokens:
BACKUPShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:00 MAIN1
Step 5: Modify the following configuration lines in DUT0 :
set interfaces ethernet eth0 vrrp vrrp-group 1 disable
Step 6: Run command system vrrp sync-group MAIN0 show at DUT0 and check if output contains the following tokens:
BACKUPShow output
Group: MAIN0 State: BACKUP Monitoring: Interface: eth0, Group: 1
Step 7: Run command system vrrp sync-group MAIN1 show at DUT1 and check if output contains the following tokens:
MASTERShow output
Group: MAIN1 State: MASTER Monitoring: Interface: eth0, Group: 1
Two VRRP Devices In Same Sync Group With MD5 Authentication
Description
Configure 2 DUTs in the same sync-group to check that they do communicate between each other, with MD5 authentication.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 sync-group MAIN0 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp sync-group MAIN0 authentication encrypted-password U2FsdGVkX1/9YfTaW9UToM4iAFY8obfu8wtahxNYzxs= set system vrrp sync-group MAIN0 authentication type md5
Step 2: Run command system vrrp show at DUT0 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:02 MAIN0
Step 3: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 sync-group MAIN1 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp sync-group MAIN1 authentication encrypted-password U2FsdGVkX1+30ANWhqQN9JZFL2CPOmKUoZbp5eX3xXk= set system vrrp sync-group MAIN1 authentication type md5
Step 4: Run command system vrrp show at DUT1 and check if output contains the following tokens:
BACKUPShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:00 MAIN1
Step 5: Modify the following configuration lines in DUT0 :
set interfaces ethernet eth0 vrrp vrrp-group 1 disable
Step 6: Run command system vrrp sync-group MAIN0 show at DUT0 and check if output contains the following tokens:
BACKUPShow output
Group: MAIN0 State: BACKUP Monitoring: Interface: eth0, Group: 1
Step 7: Run command system vrrp sync-group MAIN1 show at DUT1 and check if output contains the following tokens:
MASTERShow output
Group: MAIN1 State: MASTER Monitoring: Interface: eth0, Group: 1
Test GARP Interval
Description
This scenario checks that an OSDx device can use VRRP configuring the delay between GARP packets sent on an interface per VRRP group.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 garp interval 5 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTER
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Interval Global
Description
This scenario checks that an OSDx device can use VRRP configuring the delay between GARP packets sent on an interface globally.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp global-parameters garp interval 5
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTER
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Master Delay
Description
This scenario checks that an OSDx device can use VRRP configuring the delay of the second set of garp packets sent after transitioning to master per VRRP group.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 garp master-delay 2 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:02 none
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Master Delay Global
Description
This scenario checks that an OSDx device can use VRRP configuring the delay of the second set of garp packets sent after transitioning to master globally.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp global-parameters garp master-delay 2
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:03 none
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Master Repeat
Description
This scenario checks that an OSDx device can use VRRP configuring the number of garp packets to send at a time after transitioning to master per VRRP group.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 garp master-repeat 3 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:03 none
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Master Repeat Global
Description
This scenario checks that an OSDx device can use VRRP configuring the number of garp packets to send at a time after transitioning to master globally.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp global-parameters garp master-repeat 3
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:03 none
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Master Refresh
Description
This scenario checks that an OSDx device can use VRRP configuring the minimum time interval for refreshing garp while master per VRRP group.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 garp master-refresh 5 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:03 none
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Master Refresh Global
Description
This scenario checks that an OSDx device can use VRRP configuring the minimum time interval for refreshing garp while master globally.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp global-parameters garp master-refresh 5
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:03 none
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Master Refresh Repeat
Description
This scenario checks that an OSDx device can use VRRP configuring the number of garp packets to send at a time while master per VRRP group.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 garp master-refresh 5 set interfaces ethernet eth0 vrrp vrrp-group 1 garp master-refresh-repeat 3 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:02 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:03 none
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64
Test GARP Master Refresh Repeat Global
Description
This scenario checks that an OSDx device can use VRRP configuring the number of garp packets to send at a time while master globally.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.101/24 set interfaces ethernet eth0 vrrp vrrp-group 1 preempt set interfaces ethernet eth0 vrrp vrrp-group 1 priority 200 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.100/24 set interfaces ethernet eth0 vrrp vrrp-group 1 priority 100 set interfaces ethernet eth0 vrrp vrrp-group 1 virtual-address 192.168.10.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrrp global-parameters garp master-refresh 5 set system vrrp global-parameters garp master-refresh-repeat 3
Step 3: Run command system vrrp show at DUT1 and check if output contains the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 MASTER yes no 0:00:01 none
Step 4: Run command system vrrp show at DUT0 and check if output does not contain the following tokens:
MASTERShow output
-------------------------------------------------------------------------------- Interface Group State RFC Compliant Addr Owner Last Transition Sync Group -------------------------------------------------------------------------------- eth0 1 BACKUP yes no 0:00:03 none
Step 5: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth0 disable
Step 6: Get the MAC address of the eth0 interface:
admin@DUT0$ interfaces ethernet eth0 show detailedShow output
---------------------------------------------------------------------------------------------------------------- Name Idx IP Address Admin Oper Link MTU Vrf Upper Lower Type Phys addr ---------------------------------------------------------------------------------------------------------------- eth0 2 192.168.100.100/24 up up up 1500 ethernet de:ad:be:ef:6c:00 192.168.10.1/32 fe80::dcad:beff:feef:6c00/64