Htb

Contents

The following scenario shows how to configure a HTB qdisc.

Test HTB QDisc

Description

In this scenario, a Hierarchy Token Bucket (HTB) qdisc is configured in DUT0 (‘eth0’ interface) to achieve linksharing among a hierarchy of classes. Three classes are created with different matches (filters). Each match is allocated to a single class and evaluated in order.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 10.0.0.2/24
set interfaces ethernet eth0 traffic control out QDISC
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set traffic control QDISC type htb bandwidth 100
set traffic control QDISC type htb class 1 bandwidth percentage 50
set traffic control QDISC type htb class 1 ceiling percentage 100
set traffic control QDISC type htb class 2 bandwidth percentage 20
set traffic control QDISC type htb class 2 ceiling percentage 0
set traffic control QDISC type htb class 3 bandwidth percentage 10
set traffic control QDISC type htb class 3 ceiling percentage 0
set traffic control QDISC type htb default-class 3
set traffic control QDISC type htb match 1 class 1
set traffic control QDISC type htb match 1 ip destination port 8080
set traffic control QDISC type htb match 2 class 2
set traffic control QDISC type htb match 2 ip protocol tcp

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 10.0.0.1/24
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Ping IP address 10.0.0.1 from DUT0:

admin@DUT0$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.319 ms

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.319/0.319/0.319/0.000 ms

Step 4: Initiate a bandwidth test from DUT0 to DUT1

admin@DUT1$ monitor test performance server port 8080
admin@DUT0$ monitor test performance client 10.0.0.1 duration 5 port 8080 parallel 1

Expect this output in DUT0:

Connecting to host 10.0.0.1, port 8080
[  5] local 10.0.0.2 port 58182 connected to 10.0.0.1 port 8080
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  13.8 MBytes   116 Mbits/sec   95    110 KBytes
[  5]   1.00-2.00   sec  11.4 MBytes  95.4 Mbits/sec   23    134 KBytes
[  5]   2.00-3.00   sec  11.3 MBytes  94.9 Mbits/sec   31   91.9 KBytes
[  5]   3.00-4.00   sec  11.3 MBytes  94.9 Mbits/sec   10   83.4 KBytes
[  5]   4.00-5.00   sec  11.7 MBytes  98.5 Mbits/sec    3    107 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-5.00   sec  59.5 MBytes  99.9 Mbits/sec  162             sender
[  5]   0.00-5.00   sec  58.5 MBytes  98.0 Mbits/sec                  receiver

iperf Done.

Step 5: Initiate a bandwidth test from DUT0 to DUT1

admin@DUT1$ monitor test performance server port 1234
admin@DUT0$ monitor test performance client 10.0.0.1 duration 5 port 1234 parallel 1

Expect this output in DUT0:

Connecting to host 10.0.0.1, port 1234
[  5] local 10.0.0.2 port 36394 connected to 10.0.0.1 port 1234
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  2.73 MBytes  22.9 Mbits/sec   34   48.1 KBytes
[  5]   1.00-2.00   sec  2.24 MBytes  18.8 Mbits/sec   39   38.2 KBytes
[  5]   2.00-3.00   sec  2.49 MBytes  20.9 Mbits/sec   45   21.2 KBytes
[  5]   3.00-4.00   sec  2.24 MBytes  18.8 Mbits/sec   25   28.3 KBytes
[  5]   4.00-5.00   sec  2.24 MBytes  18.8 Mbits/sec   23   25.5 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-5.00   sec  11.9 MBytes  20.0 Mbits/sec  166             sender
[  5]   0.00-5.00   sec  11.4 MBytes  19.1 Mbits/sec                  receiver

iperf Done.

Step 6: Run command traffic control show at DUT0 and check if output contains the following tokens:

class 1
class 2
class 3 (default)

Show output

Traffic control for interface 'eth0' - 'egress' mode

------------------------------------------------------------------------------------
ID   traffic control        type         parent  bytes sent  pkts sent  pkts dropped
------------------------------------------------------------------------------------
1:0  QDISC            htb                root      76714260      50714            36
1:1  QDISC            class 1            1:0       64168097      42401             0
1:2  QDISC            class 2            1:0       12545307       8305             0
1:3  QDISC            class 3 (default)  1:0            856          8             0
2:0  -                fq_codel           1:1       64168097      42401            10
3:0  -                fq_codel           1:2       12545307       8305            26
4:0  -                fq_codel           1:3            856          8             0

Attention

The previous command output should include packets for the different HTB classes. If not, obtaining debugging information may prove usuful. This can be achieved by setting the following configuration commands: set traffic control <NAME> type htb match 1 log <PREFIX> or set traffic policy <NAME> rule 1 log prefix <PREFIX>. After generating some traffic, the system journal monitor command can be used to review log messages.

---