Site-To-Site
This scenario shows how to configure and connect two subnets
with each other through a VPN tunnel and automatically configure
the negotiated remote prefixes as routes. DUT0 acts as a
responder and DUT1 as a initiator.
Test Site-To-Site With Basic Route Installation
Description
In this scenario, both devices install routes
for the VPN traffic in the main table.
Scenario
Step 1: Run command protocols ip show route at DUT0 and check if output does not contain the following tokens:
K>* 10.3.0.0/24
Step 2: Set the following configuration in DUT0 :
set interfaces dummy dum0 address 10.1.0.1/24 set interfaces ethernet eth0 address 80.0.0.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1+9s/GMPJ6eWFNo1IZ3zhft2s0v0mL51zo= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.2 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 0.0.0.0/0 next-hop 80.0.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19XOPR4znu8A7ntwyaItqCHJp5mlM3UKz4= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.2 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.344 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.344/0.344/0.344/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.327 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.327/0.327/0.327/0.000 ms
Step 6: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
peer-PEER-tunnel-\d+.+INSTALLEDShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 068f3d2f42ddf5aa_i 5d8b6b4113f487c5_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 28326s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3534s, expires in 3959s in c0d4fd9f, 0 bytes, 0 packets out c3dddc97, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24
Step 7: Run command protocols ip show route at DUT0 and check if output contains the following tokens:
K>* 10.3.0.0/24Show output
Codes: K - kernel route, C - connected, L - local, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, t - Table-Direct, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure C>* 10.1.0.0/24 is directly connected, dum0, weight 1, 00:00:08 L>* 10.1.0.1/32 is directly connected, dum0, weight 1, 00:00:08 K>* 10.3.0.0/24 [0/0] via 80.0.0.2, eth0, weight 1, 00:00:01 C>* 80.0.0.0/24 is directly connected, eth0, weight 1, 00:00:07 L>* 80.0.0.1/32 is directly connected, eth0, weight 1, 00:00:07
Step 8: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 9: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 10: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.524 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.524/0.524/0.524/0.000 ms
Step 11: Initiate a tcp connection from DUT1 to DUT0 and try to send some messages between both endpoints
admin@DUT0$ monitor test connection server 8080 tcp admin@DUT1$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1
Step 12: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, db7d5564a805caef_i c318793165703fa1_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 3s ago, rekeying in 24338s peer-PEER-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 3s ago, rekeying in 3548s, expires in 3957s in cd217d84, 920 bytes, 15 packets, 0s ago out c9141e2e, 868 bytes, 14 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test Site-To-Site With VRF Route Installation
Description
In this scenario, DUT0 install reoutes
in a separate VRF called LAN.
Scenario
Step 1: Run command protocols vrf LAN ip show route at DUT0 and check if output does not contain the following tokens:
K>* 10.3.0.0/24Show output
% VRF LAN not found
Step 2: Set the following configuration in DUT0 :
set interfaces dummy dum0 address 10.1.0.1/24 set interfaces dummy dum0 vrf LAN set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth0 vrf WAN set protocols vrf WAN static route 10.1.0.0/24 next-hop-vrf LAN set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf LAN set system vrf WAN set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1/yP0xjePG953H2RUUAQC55jOC38cuOWIE= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.2 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes LAN set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 0.0.0.0/0 next-hop 80.0.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1+mHpqJdUSl1AfMf5Bmb6wVqo9HYZYffrc= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.2 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.336 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.336/0.336/0.336/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 vrf WAN count 1 size 56 timeout 1Show output
ping: Warning: source address might be selected on device other than: WAN PING 80.0.0.2 (80.0.0.2) from 80.0.0.1 WAN: 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.473 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.473/0.473/0.473/0.000 ms
Step 6: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
peer-PEER-tunnel-\d+.+INSTALLEDShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 763ee1192927237a_i c536b07300cf96bd_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 20103s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3294s, expires in 3959s in ceb7dbc8, 0 bytes, 0 packets out c2d481e9, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24
Step 7: Run command protocols vrf LAN ip show route at DUT0 and check if output contains the following tokens:
K>* 10.3.0.0/24Show output
Codes: K - kernel route, C - connected, L - local, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, t - Table-Direct, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure VRF LAN: K>* 0.0.0.0/0 [255/8192] unreachable (ICMP unreachable), weight 1, 00:00:08 C>* 10.1.0.0/24 is directly connected, dum0, weight 1, 00:00:08 L>* 10.1.0.1/32 is directly connected, dum0, weight 1, 00:00:08 K>* 10.3.0.0/24 [0/0] via 80.0.0.2, eth0 (vrf WAN), weight 1, 00:00:01
Step 8: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 9: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 10: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.868 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.868/0.868/0.868/0.000 ms
Step 11: Initiate a tcp connection from DUT1 to DUT0 and try to send some messages between both endpoints
admin@DUT0$ monitor test connection server 8080 tcp vrf LAN admin@DUT1$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1
Step 12: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, 9642c54fb4b6d31e_i 6cc5285f368bb22c_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 3s ago, rekeying in 19053s peer-PEER-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 3s ago, rekeying in 3288s, expires in 3957s in c6459be5, 920 bytes, 15 packets, 0s ago out c525c657, 868 bytes, 14 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test Site-To-Site With Route Installation And Metrics
Description
In this scenario, DUT0 installs routes with
differents metrics for both IPsec peers. The point is
to check if the routes are installed correctly and most
importantly, whenever the prioritized route is down, the
backup route is used.
Scenario
Step 1: Run command protocols ip show route at DUT0 and check if output does not contain the following tokens:
K>* 10.3.0.0/24
Step 2: Set the following configuration in DUT0 :
set interfaces dummy dum0 address 10.1.0.1/24 set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 90.0.0.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1/otJybevligh/NH3OI4Ld60LT7avv+eWM= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 2 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.2 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 route-priority 10 set vpn ipsec site-to-site peer PEER1 auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER1 connection-type respond set vpn ipsec site-to-site peer PEER1 default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER1 ike-group IKE-SA set vpn ipsec site-to-site peer PEER1 local-address 90.0.0.1 set vpn ipsec site-to-site peer PEER1 remote-address 90.0.0.3 set vpn ipsec site-to-site peer PEER1 tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER1 tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER1 tunnel 1 remote prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER1 tunnel 1 route-priority 100
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 0.0.0.0/0 next-hop 80.0.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX18iyWjAZTxjpY86yHIWnFffuoTpMmHuixQ= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.2 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Set the following configuration in DUT2 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth1 address 90.0.0.3/24 set protocols static route 0.0.0.0/0 next-hop 90.0.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1/4kd4Ts0oXWX79ru5K5tB38iAVkeR5xhg= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 90.0.0.3 set vpn ipsec site-to-site peer PEER remote-address 90.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 5: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.312 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.312/0.312/0.312/0.000 ms
Step 6: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.299 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.299/0.299/0.299/0.000 ms
Step 7: Ping IP address 90.0.0.3 from DUT2:
admin@DUT2$ ping 90.0.0.3 count 1 size 56 timeout 1Show output
PING 90.0.0.3 (90.0.0.3) 56(84) bytes of data. 64 bytes from 90.0.0.3: icmp_seq=1 ttl=64 time=0.031 ms --- 90.0.0.3 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.031/0.031/0.031/0.000 ms
Step 8: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
peer-PEER-tunnel-\d+.+INSTALLEDShow output
vpn-peer-PEER1: #2, ESTABLISHED, IKEv2, 5d33ccb338afeac0_i a05e9490a8fb9499_r* local '90.0.0.1' @ 90.0.0.1[500] remote '90.0.0.3' @ 90.0.0.3[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 19438s peer-PEER1-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3287s, expires in 3959s in cb6549c1, 0 bytes, 0 packets out cbdc95d5, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24 vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 384e46629377a508_i 32872e873d7c32fa_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 7s ago, rekeying in 14814s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 7s ago, rekeying in 3380s, expires in 3953s in c99919bd, 0 bytes, 0 packets out c10370dd, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24
Step 9: Run command protocols ip show route at DUT0 and check if output contains the following tokens:
K>* 10.3.0.0/24Show output
Codes: K - kernel route, C - connected, L - local, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, t - Table-Direct, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure C>* 10.1.0.0/24 is directly connected, dum0, weight 1, 00:00:14 L>* 10.1.0.1/32 is directly connected, dum0, weight 1, 00:00:14 K * 10.3.0.0/24 [0/100] via 90.0.0.3, eth1, weight 1, 00:00:01 K>* 10.3.0.0/24 [0/10] via 80.0.0.2, eth0, weight 1, 00:00:07 C>* 80.0.0.0/24 is directly connected, eth0, weight 1, 00:00:14 L>* 80.0.0.1/32 is directly connected, eth0, weight 1, 00:00:14 C>* 90.0.0.0/24 is directly connected, eth1, weight 1, 00:00:14 L>* 90.0.0.1/32 is directly connected, eth1, weight 1, 00:00:14
Step 10: Run command show system route ip at DUT0 and check if output contains the following tokens:
10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100 10.3.0.0/24 via 80.0.0.2 dev eth0 proto static metric 10Show output
10.1.0.0/24 dev dum0 proto kernel scope link src 10.1.0.1 10.3.0.0/24 via 80.0.0.2 dev eth0 proto static metric 10 10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100 80.0.0.0/24 dev eth0 proto kernel scope link src 80.0.0.1 90.0.0.0/24 dev eth1 proto kernel scope link src 90.0.0.1
Note
The tunnel with the lowest metric configured in the route-priority parameter should be the one used to route the traffic.
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 12: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 13: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.657 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.657/0.657/0.657/0.000 ms
Step 14: Initiate a tcp connection from DUT1 to DUT0 and try to send some messages between both endpoints
admin@DUT0$ monitor test connection server 8080 tcp admin@DUT1$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1
Step 15: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #3, ESTABLISHED, IKEv2, 1ce33ab445dd2c44_i 89f4dc2f99a5e6a4_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 3s ago, rekeying in 14819s peer-PEER-tunnel-1: #3, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 3s ago, rekeying in 3511s, expires in 3957s in c3d9ab9f, 920 bytes, 15 packets, 0s ago out cdc3ed64, 868 bytes, 14 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24 vpn-peer-PEER1: #2, ESTABLISHED, IKEv2, 5d33ccb338afeac0_i a05e9490a8fb9499_r* local '90.0.0.1' @ 90.0.0.1[500] remote '90.0.0.3' @ 90.0.0.3[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 5s ago, rekeying in 19434s peer-PEER1-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 5s ago, rekeying in 3283s, expires in 3955s in cb6549c1, 0 bytes, 0 packets out cbdc95d5, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24
Note
Now we will shutdown the tunnel with the lowest metric from DUT1 and check if the traffic is routed through the backup tunnel.
Step 16: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 17: Run command vpn ipsec clear sa at DUT2 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 18: Run command vpn ipsec initiate peer PEER at DUT2 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 19: Ping IP address 10.1.0.1 from DUT2:
admin@DUT2$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.957 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.957/0.957/0.957/0.000 ms
Step 20: Initiate a tcp connection from DUT2 to DUT0 and try to send some messages between both endpoints
admin@DUT0$ monitor test connection server 8080 tcp admin@DUT2$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1
Step 21: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER1: #4, ESTABLISHED, IKEv2, 896572caf0d605be_i 3144834507878be1_r* local '90.0.0.1' @ 90.0.0.1[500] remote '90.0.0.3' @ 90.0.0.3[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 4s ago, rekeying in 18696s peer-PEER1-tunnel-1: #4, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 4s ago, rekeying in 3267s, expires in 3956s in cb8f3c25, 920 bytes, 15 packets, 0s ago out c9bec7c2, 868 bytes, 14 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Step 22: Run command show system route ip at DUT0 and check if output contains the following tokens:
10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100Show output
10.1.0.0/24 dev dum0 proto kernel scope link src 10.1.0.1 10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100 80.0.0.0/24 dev eth0 proto kernel scope link src 80.0.0.1 90.0.0.0/24 dev eth1 proto kernel scope link src 90.0.0.1
Step 23: Run command show system route ip at DUT0 and check if output does not contain the following tokens:
10.3.0.0/24 via 80.0.0.2 dev eth0 proto static metric 10Show output
10.1.0.0/24 dev dum0 proto kernel scope link src 10.1.0.1 10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100 80.0.0.0/24 dev eth0 proto kernel scope link src 80.0.0.1 90.0.0.0/24 dev eth1 proto kernel scope link src 90.0.0.1