Client Server

These scenarios show how to configure an OpenVPN tunnel using a client/server topology.

Basic Tunnel

Description

A simple client/server tunnel is created between two devices

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 192.168.100.1/24
set interfaces openvpn ovpn1 local-endpoint 10.0.0.0/29
set interfaces openvpn ovpn1 mode server tls-profile TLS
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://server.crt'
set vpn openvpn tls-profile TLS dhparam 'running://dh.pem'
set vpn openvpn tls-profile TLS private-key 'running://server.priv.pem'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 192.168.100.2/24
set interfaces openvpn ovpn1 mode client tls-profile TLS
set interfaces openvpn ovpn1 peer 1 address 192.168.100.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://client.crt'
set vpn openvpn tls-profile TLS private-key 'running://client.priv.pem'

Step 3: Ping IP address 192.168.100.2 from DUT0:

admin@DUT0$ ping 192.168.100.2 count 1 size 56 timeout 1

Show output

PING 192.168.100.2 (192.168.100.2) 56(84) bytes of data.
64 bytes from 192.168.100.2: icmp_seq=1 ttl=64 time=0.277 ms

--- 192.168.100.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.277/0.277/0.277/0.000 ms

Step 4: Run command interfaces openvpn ovpn1 status at DUT1 and check if output contains the following tokens:

CONNECTED

Show output

OpenVPN interface ovpn1
State: CONNECTED (SUCCESS)
Local endpoint: 10.0.0.2:1194
Remote: 192.168.100.1

Step 5: Ping IP address 10.0.0.1 from DUT1:

admin@DUT1$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=2.00 ms

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 2.000/2.000/2.000/0.000 ms

Step 6: Run command interfaces openvpn ovpn1 clients at DUT0 and check if output contains the following tokens:

Client

Show output

-----------------------------------------------------------------------------------
Common Name       Address        Endpoint    Connected since         Last seen
-----------------------------------------------------------------------------------
Client       192.168.100.2:1194  10.0.0.2  2025-07-28 14:17:10  2025-07-28 14:17:10

---

Basic Tunnel With VRF

Description

A simple client/server tunnel with VRF

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 192.168.100.1/24
set interfaces ethernet eth0 vrf JUPITER
set interfaces openvpn ovpn1 local-endpoint 10.0.0.0/29
set interfaces openvpn ovpn1 mode server tls-profile TLS
set interfaces openvpn ovpn1 vrf JUPITER
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf JUPITER
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://server.crt'
set vpn openvpn tls-profile TLS dhparam 'running://dh.pem'
set vpn openvpn tls-profile TLS private-key 'running://server.priv.pem'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 192.168.100.2/24
set interfaces openvpn ovpn1 mode client tls-profile TLS
set interfaces openvpn ovpn1 peer 1 address 192.168.100.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://client.crt'
set vpn openvpn tls-profile TLS private-key 'running://client.priv.pem'

Step 3: Ping IP address 192.168.100.2 from DUT0:

admin@DUT0$ ping 192.168.100.2 vrf JUPITER count 1 size 56 timeout 1

Show output

ping: Warning: source address might be selected on device other than: JUPITER
PING 192.168.100.2 (192.168.100.2) from 192.168.100.1 JUPITER: 56(84) bytes of data.
64 bytes from 192.168.100.2: icmp_seq=1 ttl=64 time=0.524 ms

--- 192.168.100.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.524/0.524/0.524/0.000 ms

Step 4: Run command interfaces openvpn ovpn1 status at DUT1 and check if output contains the following tokens:

CONNECTED

Show output

OpenVPN interface ovpn1
State: CONNECTED (SUCCESS)
Local endpoint: 10.0.0.2:1194
Remote: 192.168.100.1

Step 5: Ping IP address 10.0.0.1 from DUT1:

admin@DUT1$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=11.2 ms

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 11.182/11.182/11.182/0.000 ms

Step 6: Run command interfaces openvpn ovpn1 clients at DUT0 and check if output contains the following tokens:

Client

Show output

-----------------------------------------------------------------------------------
Common Name       Address        Endpoint    Connected since         Last seen
-----------------------------------------------------------------------------------
Client       192.168.100.2:1194  10.0.0.2  2025-07-28 14:17:25  2025-07-28 14:17:26

---

Client Static IP

Description

A client is given a static IP address based on its common name

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 192.168.100.1/24
set interfaces openvpn ovpn1 local-endpoint 10.0.0.0/29
set interfaces openvpn ovpn1 mode server server-profile SRV
set interfaces openvpn ovpn1 mode server tls-profile TLS
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn server-profile SRV client Client address 10.0.0.3
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://server.crt'
set vpn openvpn tls-profile TLS dhparam 'running://dh.pem'
set vpn openvpn tls-profile TLS private-key 'running://server.priv.pem'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 192.168.100.2/24
set interfaces openvpn ovpn1 mode client tls-profile TLS
set interfaces openvpn ovpn1 peer 1 address 192.168.100.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://client.crt'
set vpn openvpn tls-profile TLS private-key 'running://client.priv.pem'

Step 3: Ping IP address 192.168.100.2 from DUT0:

admin@DUT0$ ping 192.168.100.2 count 1 size 56 timeout 1

Show output

PING 192.168.100.2 (192.168.100.2) 56(84) bytes of data.
64 bytes from 192.168.100.2: icmp_seq=1 ttl=64 time=0.352 ms

--- 192.168.100.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.352/0.352/0.352/0.000 ms

Step 4: Run command interfaces openvpn ovpn1 status at DUT1 and check if output contains the following tokens:

CONNECTED

Show output

OpenVPN interface ovpn1
State: CONNECTED (SUCCESS)
Local endpoint: 10.0.0.3:1194
Remote: 192.168.100.1

Step 5: Ping IP address 10.0.0.3 from DUT0:

admin@DUT0$ ping 10.0.0.3 count 1 size 56 timeout 1

Show output

PING 10.0.0.3 (10.0.0.3) 56(84) bytes of data.
64 bytes from 10.0.0.3: icmp_seq=1 ttl=64 time=12.1 ms

--- 10.0.0.3 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 12.123/12.123/12.123/0.000 ms

---

Disconnect By Common Name

Description

A client is forcefully disconnected by the server by the client’s common name

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 192.168.100.1/24
set interfaces openvpn ovpn1 local-endpoint 10.0.0.0/29
set interfaces openvpn ovpn1 mode server tls-profile TLS
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://server.crt'
set vpn openvpn tls-profile TLS dhparam 'running://dh.pem'
set vpn openvpn tls-profile TLS private-key 'running://server.priv.pem'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 192.168.100.2/24
set interfaces openvpn ovpn1 mode client tls-profile TLS
set interfaces openvpn ovpn1 peer 1 address 192.168.100.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://client.crt'
set vpn openvpn tls-profile TLS private-key 'running://client.priv.pem'

Step 3: Ping IP address 192.168.100.2 from DUT0:

admin@DUT0$ ping 192.168.100.2 count 1 size 56 timeout 1

Show output

PING 192.168.100.2 (192.168.100.2) 56(84) bytes of data.
64 bytes from 192.168.100.2: icmp_seq=1 ttl=64 time=0.545 ms

--- 192.168.100.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.545/0.545/0.545/0.000 ms

Step 4: Run command interfaces openvpn ovpn1 status at DUT1 and check if output contains the following tokens:

CONNECTED

Show output

OpenVPN interface ovpn1
State: CONNECTED (SUCCESS)
Local endpoint: 10.0.0.2:1194
Remote: 192.168.100.1

Step 5: Ping IP address 10.0.0.1 from DUT1:

admin@DUT1$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.786 ms

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.786/0.786/0.786/0.000 ms

Step 6: Run command interfaces openvpn ovpn1 disconnect common-name Client at DUT0 and expect this output:

Show output

common name 'Client' found, 1 client(s) killed

Step 7: Expect a failure in the following command: Ping IP address 10.0.0.1 from DUT1:

admin@DUT1$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms

Step 8: Run command interfaces openvpn ovpn1 clients at DUT0 and check if output does not match the following regular expressions:

Client

Show output

----------------------------------------------------------
Common Name  Address  Endpoint  Connected since  Last seen
----------------------------------------------------------

---

Disconnect By Address

Description

A client is forcefully disconnected by the server by the client’s address

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 192.168.100.1/24
set interfaces openvpn ovpn1 local-endpoint 10.0.0.0/29
set interfaces openvpn ovpn1 mode server tls-profile TLS
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://server.crt'
set vpn openvpn tls-profile TLS dhparam 'running://dh.pem'
set vpn openvpn tls-profile TLS private-key 'running://server.priv.pem'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 192.168.100.2/24
set interfaces openvpn ovpn1 mode client tls-profile TLS
set interfaces openvpn ovpn1 peer 1 address 192.168.100.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set vpn openvpn tls-profile TLS ca 'running://ca.crt'
set vpn openvpn tls-profile TLS certificate 'running://client.crt'
set vpn openvpn tls-profile TLS private-key 'running://client.priv.pem'

Step 3: Ping IP address 192.168.100.2 from DUT0:

admin@DUT0$ ping 192.168.100.2 count 1 size 56 timeout 1

Show output

PING 192.168.100.2 (192.168.100.2) 56(84) bytes of data.
64 bytes from 192.168.100.2: icmp_seq=1 ttl=64 time=5.09 ms

--- 192.168.100.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.092/5.092/5.092/0.000 ms

Step 4: Run command interfaces openvpn ovpn1 status at DUT1 and check if output contains the following tokens:

CONNECTED

Show output

OpenVPN interface ovpn1
State: CONNECTED (SUCCESS)
Local endpoint: 10.0.0.2:1194
Remote: 192.168.100.1

Step 5: Ping IP address 10.0.0.1 from DUT1:

admin@DUT1$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=2.04 ms

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 2.040/2.040/2.040/0.000 ms

Step 6: Run command interfaces openvpn ovpn1 disconnect address 192.168.100.2 1194 at DUT0 and expect this output:

Show output

1 client(s) at address 192.168.100.2

Step 7: Expect a failure in the following command: Ping IP address 10.0.0.1 from DUT1:

admin@DUT1$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms

Step 8: Run command interfaces openvpn ovpn1 clients at DUT0 and check if output does not match the following regular expressions:

Client

Show output

----------------------------------------------------------
Common Name  Address  Endpoint  Connected since  Last seen
----------------------------------------------------------

---

SCEP

Description

A simple client/server tunnel is created between two devices using SCEP to get the necessary keys and certificates

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth1 address 10.215.168.64/24
set protocols static route 192.168.212.0/22 next-hop 10.215.168.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth1 address 10.215.168.65/24
set protocols static route 192.168.212.0/22 next-hop 10.215.168.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Ping IP address 192.168.213.25 from DUT0:

admin@DUT0$ ping 192.168.213.25 count 1 size 56 timeout 1

Show output

PING 192.168.213.25 (192.168.213.25) 56(84) bytes of data.
64 bytes from 192.168.213.25: icmp_seq=1 ttl=126 time=5.19 ms

--- 192.168.213.25 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.191/5.191/5.191/0.000 ms

Step 4: Ping IP address 192.168.213.25 from DUT1:

admin@DUT1$ ping 192.168.213.25 count 1 size 56 timeout 1

Show output

PING 192.168.213.25 (192.168.213.25) 56(84) bytes of data.
64 bytes from 192.168.213.25: icmp_seq=1 ttl=126 time=0.946 ms

--- 192.168.213.25 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.946/0.946/0.946/0.000 ms

Step 5: Modify the following configuration lines in DUT0 :

set interfaces ethernet eth0 address 192.168.100.1/24
set interfaces openvpn ovpn1 local-endpoint 10.0.0.0/29
set interfaces openvpn ovpn1 mode server tls-profile TLS
set system certificate scep csr CSR cgi-path CertSrv/mscep/mscep.dll/pkiclient.exe
set system certificate scep csr CSR distinguished-names CN=Server
set system certificate scep csr CSR encrypted-password U2FsdGVkX19AhRFhZK14kQy2AHK+hbkblLWl93dviWWUyy7E74tk8mDaO1yT5p78aBT9Rc+9FouS9A8xX+3IHw==
set system certificate scep csr CSR url 'http://192.168.213.25/'
set vpn openvpn tls-profile TLS csr CSR
set vpn openvpn tls-profile TLS dhparam 'running://dh.pem'

Step 6: Modify the following configuration lines in DUT1 :

set interfaces ethernet eth0 address 192.168.100.2/24
set interfaces openvpn ovpn1 mode client tls-profile TLS
set interfaces openvpn ovpn1 peer 1 address 192.168.100.1
set system certificate scep csr CSR cgi-path CertSrv/mscep/mscep.dll/pkiclient.exe
set system certificate scep csr CSR distinguished-names CN=Client
set system certificate scep csr CSR encrypted-password U2FsdGVkX19S+PmXfiSw4HaPVoDfGYd3uG49iOtoC+j9S16paI1089XfoUCvfrANwXPev3jQzYGaW/lLzphlmg==
set system certificate scep csr CSR url 'http://192.168.213.25/'
set vpn openvpn tls-profile TLS csr CSR

Step 7: Run command pki scep show CSR at DUT0 and check if output matches the following regular expressions:

usercert\s+Valid

Show output

-------------------------------------------------------------------------------------
Certificate  Status     Usage             NotBefore                  NotAfter
-------------------------------------------------------------------------------------
ca           Valid   Signature     Dec 14 10:00:35 2023 GMT  Dec 14 10:10:34 2053 GMT
ra           Valid   Encipherment  Dec 21 09:33:45 2023 GMT  Dec 20 09:33:45 2025 GMT
ra-2         Valid   Signature     Dec 21 09:33:43 2023 GMT  Dec 20 09:33:43 2025 GMT
usercert     Valid   -             Jul 28 13:58:39 2025 GMT  Jul 28 17:58:39 2025 GMT

Step 8: Ping IP address 192.168.100.2 from DUT0:

admin@DUT0$ ping 192.168.100.2 count 1 size 56 timeout 1

Show output

PING 192.168.100.2 (192.168.100.2) 56(84) bytes of data.
64 bytes from 192.168.100.2: icmp_seq=1 ttl=64 time=0.336 ms

--- 192.168.100.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.336/0.336/0.336/0.000 ms

Step 9: Run command interfaces openvpn ovpn1 status at DUT1 and check if output contains the following tokens:

CONNECTED

Show output

OpenVPN interface ovpn1
State: CONNECTED (SUCCESS)
Local endpoint: 10.0.0.2:1194
Remote: 192.168.100.1

Step 10: Ping IP address 10.0.0.1 from DUT1:

admin@DUT1$ ping 10.0.0.1 count 1 size 56 timeout 1

Show output

PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.544 ms

--- 10.0.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.544/0.544/0.544/0.000 ms

---