Bfd Static Route6

Tests to check BFD protocol in static routes for IPv6.

Test Connection With Next Hop

Description

Checks connection between two devices with BFD in static routes using the gateway as the BFD peer.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '::/0' next-hop '3fff:10::200' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

peer 3fff:10::200
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF MON IPv4 Unicast:

    VRF MON IPv4 Multicast:

    VRF MON IPv6 Unicast:
    VRF TEST IPv4 Unicast:

    VRF TEST IPv4 Multicast:

    VRF TEST IPv6 Unicast:
    VRF VRF1 IPv4 Unicast:

    VRF VRF1 IPv4 Multicast:

    VRF VRF1 IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: uninstalled)
    VRF test IPv4 Unicast:

    VRF test IPv4 Multicast:

    VRF test IPv6 Unicast:
    VRF test2 IPv4 Unicast:

    VRF test2 IPv4 Multicast:

    VRF test2 IPv6 Unicast:

Step 4: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

peer 3fff:10::100
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: uninstalled)

Step 5: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

peer 3fff:10::200
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 3109197368
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 6: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

peer 3fff:10::100
Show output
BFD Peers:
        peer 3fff:10::100 vrf default
                ID: 654132281
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 7: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF MON IPv4 Unicast:

    VRF MON IPv4 Multicast:

    VRF MON IPv6 Unicast:
    VRF TEST IPv4 Unicast:

    VRF TEST IPv4 Multicast:

    VRF TEST IPv6 Unicast:
    VRF VRF1 IPv4 Unicast:

    VRF VRF1 IPv4 Multicast:

    VRF VRF1 IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: installed)
    VRF test IPv4 Unicast:

    VRF test IPv4 Multicast:

    VRF test IPv6 Unicast:
    VRF test2 IPv4 Unicast:

    VRF test2 IPv4 Multicast:

    VRF test2 IPv6 Unicast:

Step 8: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: installed)

Step 9: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 3109197368
                Remote ID: 654132281
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 10: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 3fff:10::100 vrf default
                ID: 654132281
                Remote ID: 3109197368
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 11: Ping IP address 3fff:10::200 from DUT0:

admin@DUT0$ ping 3fff:10::200 count 1 size 56 timeout 1
Show output
PING 3fff:10::200(3fff:10::200) 56 data bytes
64 bytes from 3fff:10::200: icmp_seq=1 ttl=64 time=0.191 ms

--- 3fff:10::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.191/0.191/0.191/0.000 ms

Step 12: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=64 time=0.191 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.191/0.191/0.191/0.000 ms

Test Connection With Next Hop And Interface

Description

Checks connection between two devices with BFD in static routes using the gateway as the BFD peer and an interface.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '::/0' next-hop '3fff:10::200' interface eth0 bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' interface eth0 bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

peer 3fff:10::200
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF MON IPv4 Unicast:

    VRF MON IPv4 Multicast:

    VRF MON IPv6 Unicast:
    VRF TEST IPv4 Unicast:

    VRF TEST IPv4 Multicast:

    VRF TEST IPv6 Unicast:
    VRF VRF1 IPv4 Unicast:

    VRF VRF1 IPv4 Multicast:

    VRF VRF1 IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: uninstalled)
    VRF test IPv4 Unicast:

    VRF test IPv4 Multicast:

    VRF test IPv6 Unicast:
    VRF test2 IPv4 Unicast:

    VRF test2 IPv4 Multicast:

    VRF test2 IPv6 Unicast:

Step 4: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

peer 3fff:10::100
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: uninstalled)

Step 5: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

peer 3fff:10::200
Show output
BFD Peers:
        peer 3fff:10::200 vrf default interface eth0
                ID: 1934479345
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 6: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

peer 3fff:10::100
Show output
BFD Peers:
        peer 3fff:10::100 vrf default interface eth0
                ID: 1142073436
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 7: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF MON IPv4 Unicast:

    VRF MON IPv4 Multicast:

    VRF MON IPv6 Unicast:
    VRF TEST IPv4 Unicast:

    VRF TEST IPv4 Multicast:

    VRF TEST IPv6 Unicast:
    VRF VRF1 IPv4 Unicast:

    VRF VRF1 IPv4 Multicast:

    VRF VRF1 IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: installed)
    VRF test IPv4 Unicast:

    VRF test IPv4 Multicast:

    VRF test IPv6 Unicast:
    VRF test2 IPv4 Unicast:

    VRF test2 IPv4 Multicast:

    VRF test2 IPv6 Unicast:

Step 8: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: installed)

Step 9: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 3fff:10::200 vrf default interface eth0
                ID: 1934479345
                Remote ID: 1142073436
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 10: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 3fff:10::100 vrf default interface eth0
                ID: 1142073436
                Remote ID: 1934479345
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 11: Ping IP address 3fff:10::200 from DUT0:

admin@DUT0$ ping 3fff:10::200 count 1 size 56 timeout 1
Show output
PING 3fff:10::200(3fff:10::200) 56 data bytes
64 bytes from 3fff:10::200: icmp_seq=1 ttl=64 time=0.193 ms

--- 3fff:10::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.193/0.193/0.193/0.000 ms

Step 12: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=64 time=0.204 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.204/0.204/0.204/0.000 ms

Test Connection With Next Hop And Next Hop VRF

Description

Checks connection between two devices with BFD in static routes using the gateway as the BFD peer and a leaked route with a nexthop in the specified VRF ID.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set interfaces ethernet eth0 vrf VRF
set protocols static route6 '::/0' next-hop '3fff:10::200' next-hop-vrf VRF bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf VRF

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set interfaces ethernet eth0 vrf VRF
set protocols static route6 '::/0' next-hop '3fff:10::100' next-hop-vrf VRF bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf VRF

Step 3: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

peer 3fff:10::200
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF MON IPv4 Unicast:

    VRF MON IPv4 Multicast:

    VRF MON IPv6 Unicast:
    VRF TEST IPv4 Unicast:

    VRF TEST IPv4 Multicast:

    VRF TEST IPv6 Unicast:
    VRF VRF1 IPv4 Unicast:

    VRF VRF1 IPv4 Multicast:

    VRF VRF1 IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: uninstalled)
    VRF test IPv4 Unicast:

    VRF test IPv4 Multicast:

    VRF test IPv6 Unicast:
    VRF test2 IPv4 Unicast:

    VRF test2 IPv4 Multicast:

    VRF test2 IPv6 Unicast:

Step 4: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

peer 3fff:10::100
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: uninstalled)

Step 5: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

peer 3fff:10::200
Show output
BFD Peers:
        peer 3fff:10::200 vrf VRF
                ID: 4153453459
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 6: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

peer 3fff:10::100
Show output
BFD Peers:
        peer 3fff:10::100 vrf VRF
                ID: 32433785
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 7: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF MON IPv4 Unicast:

    VRF MON IPv4 Multicast:

    VRF MON IPv6 Unicast:
    VRF TEST IPv4 Unicast:

    VRF TEST IPv4 Multicast:

    VRF TEST IPv6 Unicast:
    VRF VRF1 IPv4 Unicast:

    VRF VRF1 IPv4 Multicast:

    VRF VRF1 IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: installed)
    VRF test IPv4 Unicast:

    VRF test IPv4 Multicast:

    VRF test IPv6 Unicast:
    VRF test2 IPv4 Unicast:

    VRF test2 IPv4 Multicast:

    VRF test2 IPv6 Unicast:

Step 8: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: installed)

Step 9: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 3fff:10::200 vrf VRF
                ID: 4153453459
                Remote ID: 32433785
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 10: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 3fff:10::100 vrf VRF
                ID: 32433785
                Remote ID: 4153453459
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 11: Ping IP address 3fff:10::200 from DUT0:

admin@DUT0$ ping 3fff:10::200 count 1 size 56 timeout 1
Show output
PING 3fff:10::200(3fff:10::200) 56 data bytes
64 bytes from 3fff:10::200: icmp_seq=1 ttl=64 time=0.158 ms

--- 3fff:10::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.158/0.158/0.158/0.000 ms

Step 12: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=64 time=0.209 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.209/0.209/0.209/0.000 ms

Test Multihop Connection

Description

Checks multihop connection between two devices in different networks.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address '3fff:1::1/64'
set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '3fff:20::/64' next-hop '3fff:10::101'
set protocols static route6 '3fff:2::/64' next-hop '3fff:20::200' bfd multihop
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces dummy dum0 address '3fff:2::1/64'
set interfaces ethernet eth0 address '3fff:20::200/64'
set protocols static route6 '3fff:10::/64' next-hop '3fff:20::201'
set protocols static route6 '3fff:1::/64' next-hop '3fff:10::100' bfd multihop
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Set the following configuration in DUT2 :

set interfaces ethernet eth0 address '3fff:10::101/64'
set interfaces ethernet eth1 address '3fff:20::201/64'
set protocols static route6 '3fff:1::/64' next-hop '3fff:10::100'
set protocols static route6 '3fff:2::/64' next-hop '3fff:20::200'
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 4: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

peer 3fff:20::200
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF MON IPv4 Unicast:

    VRF MON IPv4 Multicast:

    VRF MON IPv6 Unicast:
    VRF TEST IPv4 Unicast:

    VRF TEST IPv4 Multicast:

    VRF TEST IPv6 Unicast:
    VRF VRF1 IPv4 Unicast:

    VRF VRF1 IPv4 Multicast:

    VRF VRF1 IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        3fff:2::/64 peer 3fff:20::200 (status: uninstalled)
    VRF test IPv4 Unicast:

    VRF test IPv4 Multicast:

    VRF test IPv6 Unicast:
    VRF test2 IPv4 Unicast:

    VRF test2 IPv4 Multicast:

    VRF test2 IPv6 Unicast:

Step 5: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

peer 3fff:10::100
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        3fff:1::/64 peer 3fff:10::100 (status: uninstalled)

Step 6: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

peer 3fff:20::200
Show output
BFD Peers:
        peer 3fff:20::200 multihop local-address 3fff:10::100 vrf default
                ID: 4074340723
                Remote ID: 0
                Active mode
                Minimum TTL: 2
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 7: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

peer 3fff:10::100
Show output
BFD Peers:
        peer 3fff:10::100 multihop local-address 3fff:20::200 vrf default
                ID: 1881028511
                Remote ID: 0
                Active mode
                Minimum TTL: 2
                Status: down
                Downtime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 8: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF MON IPv4 Unicast:

    VRF MON IPv4 Multicast:

    VRF MON IPv6 Unicast:
    VRF TEST IPv4 Unicast:

    VRF TEST IPv4 Multicast:

    VRF TEST IPv6 Unicast:
    VRF VRF1 IPv4 Unicast:

    VRF VRF1 IPv4 Multicast:

    VRF VRF1 IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        3fff:2::/64 peer 3fff:20::200 (status: installed)
    VRF test IPv4 Unicast:

    VRF test IPv4 Multicast:

    VRF test IPv6 Unicast:
    VRF test2 IPv4 Unicast:

    VRF test2 IPv4 Multicast:

    VRF test2 IPv6 Unicast:

Step 9: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        3fff:1::/64 peer 3fff:10::100 (status: installed)

Step 10: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 3fff:20::200 multihop local-address 3fff:10::100 vrf default
                ID: 4074340723
                Remote ID: 1881028511
                Active mode
                Minimum TTL: 2
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 11: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 3fff:10::100 multihop local-address 3fff:20::200 vrf default
                ID: 1881028511
                Remote ID: 4074340723
                Active mode
                Minimum TTL: 2
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 12: Ping IP address 3fff:20::200 from DUT0:

admin@DUT0$ ping 3fff:20::200 count 1 size 56 timeout 1
Show output
PING 3fff:20::200(3fff:20::200) 56 data bytes
64 bytes from 3fff:20::200: icmp_seq=1 ttl=63 time=0.263 ms

--- 3fff:20::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.263/0.263/0.263/0.000 ms

Step 13: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=63 time=0.291 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.291/0.291/0.291/0.000 ms

Test DUT0 Source IP

Description

Captures BFD packets and verifies the source address is correct when packets are sent from DUT0.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '::/0' next-hop '3fff:10::200' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' bfd source-ip '3fff:10::100'
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Test DUT1 Source IP

Description

Captures BFD packets and verifies the source address is correct when packets are sent from DUT1.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '::/0' next-hop '3fff:10::200' bfd source-ip '3fff:10::200'
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Test Profile

Description

Checks BFD profile in static routes.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols bfd profile PFL detect-multiplier 5
set protocols bfd profile PFL echo-interval 60
set protocols bfd profile PFL echo-mode
set protocols bfd profile PFL passive-mode
set protocols bfd profile PFL receive-interval 400
set protocols bfd profile PFL transmit-interval 400
set protocols static route6 '::/0' next-hop '3fff:10::200' bfd profile PFL
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

3fff:10::200
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 1711805529
                Remote ID: 0
                Passive mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 4: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Detect-multiplier: 5
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 1711805529
                Remote ID: 0
                Passive mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 5: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Echo receive interval: 60ms
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 1711805529
                Remote ID: 0
                Passive mode
                Status: down
                Downtime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 6: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Echo transmission interval: 60ms
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 1711805529
                Remote ID: 0
                Passive mode
                Status: down
                Downtime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 7: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Passive mode
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 1711805529
                Remote ID: 0
                Passive mode
                Status: down
                Downtime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 8: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Receive interval: 400ms
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 1711805529
                Remote ID: 0
                Passive mode
                Status: down
                Downtime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 9: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Transmission interval: 400ms
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 1711805529
                Remote ID: 0
                Passive mode
                Status: down
                Downtime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled