Roadwarrior
This scenario shows different ways to setup a roadwarrior VPN connection; in which, instead of using a N2N (network to network) connection, a single machine (e.g., a host) is able to connect to a remote private network.
On the one hand, DUT2 and DUT0 represent a remote branch
office. On the other hand, DUT1 is a roadwarrior that can
establish a connection to DUT2 using different virtual IPs.
Note that security associations (SAs) have to be manually
flushed with the command clear vpn ipsec sa. Depending on
the configuration parameter connection-type, the new tunnel
connections will be created or not.
Test VPN Roadwarrior Connection With VTI
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 10.1.0.1/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19I0iHfAA8DNQ4KxwDJlohQIhTMoEOa3KI= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local prefix 10.1.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 10.1.0.0/24 interface eth0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19q7Ah1WSwkDJr5ob3eoooOxlJZoObzODE= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 1 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.244 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.244/0.244/0.244/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.260 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.260/0.260/0.260/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.351 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.351/0.351/0.351/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::c46b:f4ff:fe0e:25c5/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.315 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.315/0.315/0.315/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.433 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.433/0.433/0.433/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 317e6324d7384c07_i 4e31cb932fba0b82_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 24818s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3259s, expires in 3960s in ce2cd699 (0x90000000), 168 bytes, 2 packets, 0s ago out c12ed77e (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 12: Modify the following configuration lines in DUT1 :
delete interfaces dummy dum0 address 10.3.0.1/24 set interfaces dummy dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::c46b:f4ff:fe0e:25c5/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.328 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.328/0.328/0.328/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.478 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.478/0.478/0.478/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, 58dc68c463e01cad_i 24b116050d4ca11a_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 27652s peer-PEER-tunnel-VTI: #2, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3331s, expires in 3959s in c13c0baf (0x90000000), 168 bytes, 2 packets, 0s ago out cf999422 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Test VPN Roadwarrior Connection With Global Policies
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 10.1.0.1/24 set protocols static route 10.3.0.0/24 interface eth0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19IyVtiBcYUUWbniy/OBVGCSw7U6Bk6eso= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 10.1.0.0/24 interface eth0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX18Agr4PDrsFUp2tB6wYhSnuBBO8IK9/50s= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 1 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.219 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.219/0.219/0.219/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.244 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.244/0.244/0.244/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.378 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.378/0.378/0.378/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::9ca2:a5ff:fe96:1519/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.302 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.302/0.302/0.302/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.424 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.424/0.424/0.424/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 71c934cad71d18e3_i 40e385328cff9864_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 20218s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3272s, expires in 3959s in c904a975, 168 bytes, 2 packets, 0s ago out c45da2af, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 12: Modify the following configuration lines in DUT1 :
delete interfaces dummy dum0 address 10.3.0.1/24 set interfaces dummy dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::9ca2:a5ff:fe96:1519/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.270 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.270/0.270/0.270/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.451 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.451/0.451/0.451/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, b06de8803ecd39f9_i c7bb990315645d38_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 16886s peer-PEER-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3559s, expires in 3959s in c8051e8b, 168 bytes, 2 packets, 0s ago out c6a82e9a, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test VPN Roadwarrior Connection With VTI And VIPs Pool
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 10.1.0.1/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX189ltvq+AA1Mm3XnqLJqqa/wWQthOopXHA= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec site-to-site peer PEER vti local prefix 10.1.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 set interfaces ethernet eth0 address 80.0.0.2/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1+6N/Qu95npTt/PvJWsUqudhoqAxEHOC3I= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 1 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.250 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.250/0.250/0.250/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.229 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.229/0.229/0.229/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.316 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.316/0.316/0.316/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::9ca2:a5ff:fe96:1519/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.260 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.260/0.260/0.260/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.491 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.491/0.491/0.491/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, fb04474057a62a61_i 8cd248749cb14c6c_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 19156s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3401s, expires in 3959s in cbfd4f09 (0x90000000), 168 bytes, 2 packets, 0s ago out c1de90ab (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32
Test VPN Roadwarrior Connection With Global Policies And VIPs Pool
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 10.1.0.1/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19tuUi2CydYpLrmVe7zS23gicXFNuU9oIc= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec site-to-site peer PEER vti local prefix 10.1.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 set interfaces ethernet eth0 address 80.0.0.2/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX18/yUknt6uXf72VHYOfjDhBXtpGtJd4LZA= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 1 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.194 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.194/0.194/0.194/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.215 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.215/0.215/0.215/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.284 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.284/0.284/0.284/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::9ca2:a5ff:fe96:1519/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.338 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.338/0.338/0.338/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.515 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.515/0.515/0.515/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 6d7e3250f225c050_i 12db954995aac544_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 25801s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3466s, expires in 3959s in c626c53d (0x90000000), 168 bytes, 2 packets, 0s ago out ceccfdb6 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32