Rtc
This scenario shows how to configure NTP client/server authentication.
Test RTC Synchronization
Description
Checks that RTC is working properly on machines that have an RTC device.
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 10.100.0.100/24 set protocols static route 0.0.0.0/0 next-hop 10.100.0.50 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system ntp master prefer set system ntp master stratum 3
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 10.100.0.50/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Ping IP address 10.100.0.100 from DUT0:
admin@DUT0$ ping 10.100.0.100 count 1 size 56 timeout 1Show output
PING 10.100.0.100 (10.100.0.100) 56(84) bytes of data. 64 bytes from 10.100.0.100: icmp_seq=1 ttl=64 time=0.311 ms --- 10.100.0.100 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.311/0.311/0.311/0.000 ms
Step 4: Run command set date 2026-03-23 12:00:00 at DUT0 and expect this output:
Step 5: Run command set date ntp 10.100.0.100 at DUT0 and check if output does not contain the following tokens:
skipping this serverShow output
Date was successfully updated!
Step 6: Run command show date at DUT0 and check if output does not contain the following tokens:
MonShow output
Tue 24 Mar 2026 10:14:18 +00:00
Step 7: Run command set date hwclock from-system debug at DUT0 and expect this output:
Show output
hwclock from util-linux 2.38.1 System Time: 1774347258.651150 Trying to open: /dev/rtc0 Using the rtc interface to the clock. Last drift adjustment done at 1774347258 seconds after 1969 Last calibration done at 1774347258 seconds after 1969 Hardware clock is on UTC time Assuming hardware clock is kept in UTC time. RTC type: 'rtc_cmos' Using delay: 0.500000 seconds missed it - 1774347258.651370 is too far past 1774347258.500000 (0.151370 > 0.001000) 1774347259.500000 is close enough to 1774347259.500000 (0.000000 < 0.002000) Set RTC to 1774347259 (1774347258 + 1; refsystime = 1774347258.000000) Setting Hardware Clock to 10:14:19 = 1774347259 seconds since 1969 ioctl(RTC_SET_TIME) was successful. Not adjusting drift factor because the --update-drift option was not used. New /etc/adjtime data: 0.000000 1774347258 0.000000 1774347258 UTC
Step 8: Run command set date hwclock to-system debug at DUT0 and expect this output:
Show output
hwclock from util-linux 2.38.1 System Time: 1774347259.598316 Trying to open: /dev/rtc0 Using the rtc interface to the clock. Last drift adjustment done at 1774347258 seconds after 1969 Last calibration done at 1774347258 seconds after 1969 Hardware clock is on UTC time Assuming hardware clock is kept in UTC time. Waiting for clock tick... ...got clock tick Time read from Hardware Clock: 2026/03/24 10:14:20 Hw clock time : 2026/03/24 10:14:20 = 1774347260 seconds since 1969 Time since last adjustment is 2 seconds Calculated Hardware Clock drift is 0.000000 seconds Calling settimeofday(NULL, 0) to lock the warp_clock function. Calling settimeofday(1774347260.000000, NULL) to set the System time.
Step 9: Run command show date at DUT0 and check if output does not contain the following tokens:
MonShow output
Tue 24 Mar 2026 10:14:20 +00:00
Test RTC Synchronization With Drift
Description
Tests that RTC is working properly on machines that have an RTC device (while adjusting the drift too).
Scenario
Step 1: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 10.100.0.100/24 set protocols static route 0.0.0.0/0 next-hop 10.100.0.50 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system ntp master prefer set system ntp master stratum 3
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 10.100.0.50/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Ping IP address 10.100.0.100 from DUT0:
admin@DUT0$ ping 10.100.0.100 count 1 size 56 timeout 1Show output
PING 10.100.0.100 (10.100.0.100) 56(84) bytes of data. 64 bytes from 10.100.0.100: icmp_seq=1 ttl=64 time=0.390 ms --- 10.100.0.100 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.390/0.390/0.390/0.000 ms
Step 4: Run command set date 2026-03-23 12:00:00 at DUT0 and expect this output:
Step 5: Run command set date ntp 10.100.0.100 at DUT0 and check if output does not contain the following tokens:
skipping this serverShow output
Date was successfully updated!
Step 6: Run command show date at DUT0 and check if output does not contain the following tokens:
MonShow output
Tue 24 Mar 2026 10:14:29 +00:00
Step 7: Run command set date hwclock from-system update-drift debug at DUT0 and expect this output:
Show output
hwclock from util-linux 2.38.1 System Time: 1774347269.681116 Trying to open: /dev/rtc0 Using the rtc interface to the clock. Last drift adjustment done at 1774347268 seconds after 1969 Last calibration done at 1774347268 seconds after 1969 Hardware clock is on UTC time Assuming hardware clock is kept in UTC time. Waiting for clock tick... ...got clock tick Time read from Hardware Clock: 2026/03/24 10:14:30 Hw clock time : 2026/03/24 10:14:30 = 1774347270 seconds since 1969 Time since last adjustment is 2 seconds Calculated Hardware Clock drift is 0.000000 seconds RTC type: 'rtc_cmos' Using delay: 0.500000 seconds 1774347270.500000 is close enough to 1774347270.500000 (0.000000 < 0.001000) Set RTC to 1774347270 (1774347270 + 0; refsystime = 1774347270.000000) Setting Hardware Clock to 10:14:30 = 1774347270 seconds since 1969 ioctl(RTC_SET_TIME) was successful. Not adjusting drift factor because it has been less than four hours since the last calibration. New /etc/adjtime data: 0.000000 1774347270 0.000000 1774347270 UTC
Step 8: Run command set date hwclock to-system debug at DUT0 and expect this output:
Show output
hwclock from util-linux 2.38.1 System Time: 1774347270.564931 Trying to open: /dev/rtc0 Using the rtc interface to the clock. Last drift adjustment done at 1774347270 seconds after 1969 Last calibration done at 1774347270 seconds after 1969 Hardware clock is on UTC time Assuming hardware clock is kept in UTC time. Waiting for clock tick... ...got clock tick Time read from Hardware Clock: 2026/03/24 10:14:31 Hw clock time : 2026/03/24 10:14:31 = 1774347271 seconds since 1969 Time since last adjustment is 1 second Calculated Hardware Clock drift is 0.000000 seconds Calling settimeofday(NULL, 0) to lock the warp_clock function. Calling settimeofday(1774347271.000000, NULL) to set the System time.
Step 9: Run command show date at DUT0 and check if output does not contain the following tokens:
MonShow output
Tue 24 Mar 2026 10:14:31 +00:00