Bonding
These scenarios cover some aspects related to link-aggregation, which is the technique of combining multiple network connections in parallel in order to increase throughput, to provide redundancy or both. On OSDx, this can be achieved by using bonding interfaces.
Test Round-Robin Mode
Description
A bonding interface is configured in DUT0 using the round-robin mode. This mode can be used to achieve load-balancing.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces bonding bond0 address 192.168.100.10/24 set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 mode round-robin set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.20/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c01/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: load balancing (round-robin)Show output
Ethernet Channel Bonding Driver: v6.1.128 Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 1 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.341 ms --- 192.168.100.20 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.341/0.341/0.341/0.000 ms
Step 6: Run command interfaces ethernet clear at DUT0.
Step 7: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 59502 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 94.9 MBytes 796 Mbits/sec 246 346 KBytes [ 5] 1.00-2.00 sec 104 MBytes 872 Mbits/sec 242 450 KBytes [ 5] 2.00-3.00 sec 231 MBytes 1.94 Gbits/sec 221 679 KBytes [ 5] 3.00-4.00 sec 322 MBytes 2.71 Gbits/sec 282 912 KBytes [ 5] 4.00-5.00 sec 338 MBytes 2.83 Gbits/sec 77 1.04 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 1.06 GBytes 1.83 Gbits/sec 1068 sender [ 5] 0.00-5.00 sec 1.06 GBytes 1.82 Gbits/sec receiver iperf Done.
Step 8: Run command interfaces ethernet show counters at DUT0 and check if output matches the following regular expressions:
eth0\s+up\s+\d+\s+\d+\s+0\s+\d{2,} eth1\s+up\s+\d+\s+\d+\s+0\s+\d{2,}Show output
----------------------------------------------------------------------------- Name Oper Rx Packets Rx Bytes Rx Errors Tx Packets Tx Bytes Tx Errors ----------------------------------------------------------------------------- eth0 up 98226 7898231 0 394558 597339254 0 eth1 up 105917 8482902 0 394390 597078611 0
Test Active-Backup Mode
Description
A bonding interface is configured in DUT0 using the active-backup mode. This mode can be used to achieve a higher degree of fault-tolerance.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces bonding bond0 address 192.168.100.10/24 set interfaces bonding bond0 miimon 100 set interfaces bonding bond0 mode active-backup set interfaces ethernet eth0 bond-group bond0 set interfaces ethernet eth1 bond-group bond0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.20/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command interfaces bonding show at DUT0 and check if output matches the following regular expressions:
bond0\s+192.168.100\.10\/24\s+up\s+upShow output
------------------------------------------------------------------ Name IP Address Admin Oper Vrf Description ------------------------------------------------------------------ bond0 192.168.100.10/24 up up fe80::dcad:beff:feef:6c01/64
Step 4: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Bonding Mode: fault-tolerance (active-backup)Show output
Ethernet Channel Bonding Driver: v6.1.128 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 count 1 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.306 ms --- 192.168.100.20 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.306/0.306/0.306/0.000 ms
Step 6: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 38044 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 201 MBytes 1.68 Gbits/sec 0 1.56 MBytes [ 5] 1.00-2.00 sec 305 MBytes 2.56 Gbits/sec 0 1.64 MBytes [ 5] 2.00-3.00 sec 319 MBytes 2.67 Gbits/sec 230 1.33 MBytes [ 5] 3.00-4.00 sec 328 MBytes 2.75 Gbits/sec 0 1.43 MBytes [ 5] 4.00-5.00 sec 352 MBytes 2.96 Gbits/sec 0 1.50 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 1.47 GBytes 2.52 Gbits/sec 230 sender [ 5] 0.00-5.00 sec 1.47 GBytes 2.52 Gbits/sec receiver iperf Done.
Step 7: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth0Show output
Ethernet Channel Bonding Driver: v6.1.128 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0
Step 8: Initiate a bandwidth test from DUT0 to DUT1
admin@DUT1$ monitor test performance server port 5001 admin@DUT0$ monitor test performance client 192.168.100.20 duration 5 port 5001 parallel 1Expect this output in
DUT0:Connecting to host 192.168.100.20, port 5001 [ 5] local 192.168.100.10 port 38072 connected to 192.168.100.20 port 5001 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 294 MBytes 2.47 Gbits/sec 0 1.63 MBytes [ 5] 1.00-2.00 sec 356 MBytes 2.99 Gbits/sec 0 2.15 MBytes [ 5] 2.00-3.00 sec 368 MBytes 3.08 Gbits/sec 0 2.15 MBytes [ 5] 3.00-4.00 sec 286 MBytes 2.40 Gbits/sec 0 2.15 MBytes [ 5] 4.00-5.00 sec 355 MBytes 2.98 Gbits/sec 146 1.63 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.00 sec 1.62 GBytes 2.78 Gbits/sec 146 sender [ 5] 0.00-5.00 sec 1.62 GBytes 2.78 Gbits/sec receiver iperf Done.
Step 9: Run command interfaces bonding bond0 show ports at DUT0 and check if output contains the following tokens:
Currently Active Slave: eth1Show output
Ethernet Channel Bonding Driver: v6.1.128 Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 Slave Interface: eth1 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:01 Slave queue ID: 0 Slave Interface: eth0 MII Status: down Speed: Unknown Duplex: Unknown Link Failure Count: 1 Permanent HW addr: de:ad:be:ef:6c:00 Slave queue ID: 0