Bfd Ospf

Test to check BFD protocol in OSPF.

Test Connection

Description

Tests BFD connection in OSPF.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.1.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Ping IP address 192.168.1.2 from DUT0:

admin@DUT0$ ping 192.168.1.2 count 1 size 56 timeout 1
Show output
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.350 ms

--- 192.168.1.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.350/0.350/0.350/0.000 ms

Step 4: Ping IP address 192.168.1.1 from DUT1:

admin@DUT1$ ping 192.168.1.1 count 1 size 56 timeout 1
Show output
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.218 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.218/0.218/0.218/0.000 ms

Step 5: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

2.2.2.2
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
2.2.2.2           1 Full/-          0.765s            39.233s 192.168.1.2     eth0:192.168.1.1                     1     0     0

Step 6: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

1.1.1.1
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          0.854s            37.171s 192.168.1.1     eth0:192.168.1.2                     1     0     0

Step 7: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

peer 192.168.1.2
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 3704155064
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 8: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

peer 192.168.1.1
Show output
BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 3528746747
                Remote ID: 3704155064
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 9: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 3704155064
                Remote ID: 3528746747
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 10: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 3528746747
                Remote ID: 3704155064
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Test Connection With Three Devices

Description

Tests BFD connection in OSPF between 3 devices.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.2.1/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf area 1 network 192.168.2.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.2.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.3.2/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 1 network 192.168.2.0/24
set protocols ospf area 2 network 192.168.3.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Set the following configuration in DUT2 :

set interfaces dummy dum0 address 10.0.0.3/24
set interfaces ethernet eth0 address 192.168.1.3/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.3.3/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf area 2 network 192.168.3.0/24
set protocols ospf parameters router-id 3.3.3.3
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 4: Ping IP address 192.168.1.3 from DUT0:

admin@DUT0$ ping 192.168.1.3 count 1 size 56 timeout 1
Show output
PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data.
64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.223 ms

--- 192.168.1.3 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.223/0.223/0.223/0.000 ms

Step 5: Ping IP address 192.168.2.2 from DUT0:

admin@DUT0$ ping 192.168.2.2 count 1 size 56 timeout 1
Show output
PING 192.168.2.2 (192.168.2.2) 56(84) bytes of data.
64 bytes from 192.168.2.2: icmp_seq=1 ttl=64 time=0.395 ms

--- 192.168.2.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.395/0.395/0.395/0.000 ms

Step 6: Ping IP address 192.168.2.1 from DUT1:

admin@DUT1$ ping 192.168.2.1 count 1 size 56 timeout 1
Show output
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
64 bytes from 192.168.2.1: icmp_seq=1 ttl=64 time=0.217 ms

--- 192.168.2.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.217/0.217/0.217/0.000 ms

Step 7: Ping IP address 192.168.3.3 from DUT1:

admin@DUT1$ ping 192.168.3.3 count 1 size 56 timeout 1
Show output
PING 192.168.3.3 (192.168.3.3) 56(84) bytes of data.
64 bytes from 192.168.3.3: icmp_seq=1 ttl=64 time=0.244 ms

--- 192.168.3.3 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.244/0.244/0.244/0.000 ms

Step 8: Ping IP address 192.168.1.1 from DUT2:

admin@DUT2$ ping 192.168.1.1 count 1 size 56 timeout 1
Show output
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.210 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.210/0.210/0.210/0.000 ms

Step 9: Ping IP address 192.168.3.2 from DUT2:

admin@DUT2$ ping 192.168.3.2 count 1 size 56 timeout 1
Show output
PING 192.168.3.2 (192.168.3.2) 56(84) bytes of data.
64 bytes from 192.168.3.2: icmp_seq=1 ttl=64 time=0.261 ms

--- 192.168.3.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.261/0.261/0.261/0.000 ms

Step 10: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

3.3.3.3
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
3.3.3.3           1 Init/-          0.695s            39.304s 192.168.1.3     eth0:192.168.1.1                     0     0     0

Step 11: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

2.2.2.2
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
3.3.3.3           1 Full/-          3.373s            30.809s 192.168.1.3     eth0:192.168.1.1                     1     0     0
2.2.2.2           1 Full/-          1.357s            38.641s 192.168.2.2     eth1:192.168.2.1                     1     0     0

Step 12: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

1.1.1.1
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          1.446s            36.538s 192.168.2.1     eth0:192.168.2.2                     1     0     0
3.3.3.3           1 Full/-          1.444s            30.721s 192.168.3.3     eth1:192.168.3.2                     1     0     0

Step 13: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

3.3.3.3
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          1.538s            36.446s 192.168.2.1     eth0:192.168.2.2                     1     0     0
3.3.3.3           1 Full/-          1.537s            30.628s 192.168.3.3     eth1:192.168.3.2                     1     0     0

Step 14: Run command protocols ospf show neighbor at DUT2 and check if output matches the following regular expressions:

1.1.1.1
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          3.635s            36.363s 192.168.1.1     eth0:192.168.1.3                     1     0     0
2.2.2.2           1 Full/-          1.619s            38.380s 192.168.3.2     eth1:192.168.3.3                     1     0     0

Step 15: Run command protocols ospf show neighbor at DUT2 and check if output matches the following regular expressions:

2.2.2.2
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          3.730s            36.268s 192.168.1.1     eth0:192.168.1.3                     1     0     0
2.2.2.2           1 Full/-          1.713s            38.285s 192.168.3.2     eth1:192.168.3.3                     1     0     0

Step 16: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

peer 192.168.1.3
Show output
BFD Peers:
        peer 192.168.2.2 vrf default interface eth1
                ID: 3161937840
                Remote ID: 1067162776
                Active mode
                Status: init
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: 50ms

        peer 192.168.1.3 vrf default interface eth0
                ID: 2894138550
                Remote ID: 2843106083
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 17: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

peer 192.168.2.2
Show output
BFD Peers:
        peer 192.168.2.2 vrf default interface eth1
                ID: 3161937840
                Remote ID: 1067162776
                Active mode
                Status: init
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: 50ms

        peer 192.168.1.3 vrf default interface eth0
                ID: 2894138550
                Remote ID: 2843106083
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 18: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

peer 192.168.2.1
Show output
BFD Peers:
        peer 192.168.3.3 vrf default interface eth1
                ID: 1716662150
                Remote ID: 1241219359
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

        peer 192.168.2.1 vrf default interface eth0
                ID: 1067162776
                Remote ID: 3161937840
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 19: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

peer 192.168.3.3
Show output
BFD Peers:
        peer 192.168.3.3 vrf default interface eth1
                ID: 1716662150
                Remote ID: 1241219359
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

        peer 192.168.2.1 vrf default interface eth0
                ID: 1067162776
                Remote ID: 3161937840
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 20: Run command protocols bfd show peers at DUT2 and check if output matches the following regular expressions:

peer 192.168.1.1
Show output
BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 2843106083
                Remote ID: 2894138550
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

        peer 192.168.3.2 vrf default interface eth1
                ID: 1241219359
                Remote ID: 1716662150
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 21: Run command protocols bfd show peers at DUT2 and check if output matches the following regular expressions:

peer 192.168.3.2
Show output
BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 2843106083
                Remote ID: 2894138550
                Active mode
                Status: up
                Uptime: 3 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

        peer 192.168.3.2 vrf default interface eth1
                ID: 1241219359
                Remote ID: 1716662150
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Test Profile

Description

Checks BFD profile in OSPF.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols bfd profile PFL detect-multiplier 5
set protocols bfd profile PFL echo-interval 60
set protocols bfd profile PFL echo-mode
set protocols bfd profile PFL passive-mode
set protocols bfd profile PFL receive-interval 400
set protocols bfd profile PFL transmit-interval 400
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Modify the following configuration lines in DUT0 :

set interfaces ethernet eth0 ip ospf bfd profile PFL

Step 3: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.1.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 4: Ping IP address 192.168.1.2 from DUT0:

admin@DUT0$ ping 192.168.1.2 count 1 size 56 timeout 1
Show output
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.268 ms

--- 192.168.1.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.268/0.268/0.268/0.000 ms

Step 5: Ping IP address 192.168.1.1 from DUT1:

admin@DUT1$ ping 192.168.1.1 count 1 size 56 timeout 1
Show output
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.259 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.259/0.259/0.259/0.000 ms

Step 6: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

192.168.1.2
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
2.2.2.2           1 Init/-          0.366s            39.633s 192.168.1.2     eth0:192.168.1.1                     0     0     0

Step 7: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

192.168.1.1
Show output
Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          0.880s            39.119s 192.168.1.1     eth0:192.168.1.2                     1     0     0

Step 8: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

192.168.1.2
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 736300818
                Remote ID: 0
                Passive mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

Step 9: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

192.168.1.1
Show output
BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 1707290730
                Remote ID: 736300818
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms

Step 10: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 736300818
                Remote ID: 1707290730
                Passive mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 240/301/397 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 11: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

Status: up
Show output
BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 1707290730
                Remote ID: 736300818
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms

Step 12: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Detect-multiplier: 5
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 736300818
                Remote ID: 1707290730
                Passive mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 222/282/397 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 13: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Echo receive interval: 60ms
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 736300818
                Remote ID: 1707290730
                Passive mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 222/259/318 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 14: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Echo transmission interval: 60ms
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 736300818
                Remote ID: 1707290730
                Passive mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 224/251/280 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 15: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Passive mode
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 736300818
                Remote ID: 1707290730
                Passive mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 225/258/281 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 16: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Receive interval: 400ms
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 736300818
                Remote ID: 1707290730
                Passive mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 225/267/338 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 17: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

Transmission interval: 400ms
Show output
BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 736300818
                Remote ID: 1707290730
                Passive mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 225/274/338 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms