Site-To-Site
This scenario shows how to configure and connect two subnets
with each other through a VPN tunnel and automatically configure
the negotiated remote prefixes as routes. DUT0 acts as a
responder and DUT1 as a initiator.
Test Site-To-Site With Basic Route Installation
Description
In this scenario, both devices install routes
for the VPN traffic in the main table.
Scenario
Step 1: Run command protocols ip show route at DUT0 and check if output does not contain the following tokens:
K>* 10.3.0.0/24Show output
Codes: K - kernel route, C - connected, L - local, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, t - Table-Direct, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure L 192.168.100.100/32 is directly connected, eth0 inactive, weight 1, 00:20:38
Step 2: Set the following configuration in DUT0 :
set interfaces dummy dum0 address 10.1.0.1/24 set interfaces ethernet eth0 address 80.0.0.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19OB7D2mlMOxv+tTRZPi1ROYCKfuU1HjjQ= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.2 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 0.0.0.0/0 next-hop 80.0.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1+UUFEWhjjbwCTIAxNmw0DS+PC7rxJTqAE= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.2 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.245 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.245/0.245/0.245/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.238 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.238/0.238/0.238/0.000 ms
Step 6: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
peer-PEER-tunnel-\d+.+INSTALLEDShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, d2a41759c5c168fb_i 5f95b5eb53656b31_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 23151s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3394s, expires in 3959s in c95389bc, 0 bytes, 0 packets out cf428605, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24
Step 7: Run command protocols ip show route at DUT0 and check if output contains the following tokens:
K>* 10.3.0.0/24Show output
Codes: K - kernel route, C - connected, L - local, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, t - Table-Direct, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure C>* 10.1.0.0/24 is directly connected, dum0, weight 1, 00:00:06 L>* 10.1.0.1/32 is directly connected, dum0, weight 1, 00:00:06 K>* 10.3.0.0/24 [0/0] via 80.0.0.2, eth0, weight 1, 00:00:01 C>* 80.0.0.0/24 is directly connected, eth0, weight 1, 00:00:06 L>* 80.0.0.1/32 is directly connected, eth0, weight 1, 00:00:06 L 192.168.100.100/32 is directly connected, eth0 inactive, weight 1, 00:20:46
Step 8: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 9: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 10: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.303 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.303/0.303/0.303/0.000 ms
Step 11: Initiate a tcp connection from DUT1 to DUT0 and try to send some messages between both endpoints
admin@DUT0$ monitor test connection server 8080 tcp admin@DUT1$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1
Step 12: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, 7642a1f7331378b2_i e7fbf03647fa4b19_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 3s ago, rekeying in 24572s peer-PEER-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 3s ago, rekeying in 3268s, expires in 3957s in c3047231, 868 bytes, 14 packets, 1s ago out cfa4d39d, 816 bytes, 13 packets, 1s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test Site-To-Site With VRF Route Installation
Description
In this scenario, DUT0 install reoutes
in a separate VRF called LAN.
Scenario
Step 1: Run command protocols vrf LAN ip show route at DUT0 and check if output does not contain the following tokens:
K>* 10.3.0.0/24Show output
% VRF LAN not found
Step 2: Set the following configuration in DUT0 :
set interfaces dummy dum0 address 10.1.0.1/24 set interfaces dummy dum0 vrf LAN set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth0 vrf WAN set protocols vrf WAN static route 10.1.0.0/24 next-hop-vrf LAN set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf LAN set system vrf WAN set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX19r3CiSEd1H2hccAficbhmkWGun3snhc/M= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.2 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes LAN set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 0.0.0.0/0 next-hop 80.0.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX18BpATNoBdQ5k//++2duoIny6ZPae/LHV4= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.2 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.225 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.225/0.225/0.225/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 vrf WAN count 1 size 56 timeout 1Show output
ping: Warning: source address might be selected on device other than: WAN PING 80.0.0.2 (80.0.0.2) from 80.0.0.1 WAN: 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.227 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.227/0.227/0.227/0.000 ms
Step 6: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
peer-PEER-tunnel-\d+.+INSTALLEDShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, a914944c363ed539_i a62ba06ca8fdaa07_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 25039s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3242s, expires in 3960s in c4bfa6fd, 0 bytes, 0 packets out cd045a29, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24
Step 7: Run command protocols vrf LAN ip show route at DUT0 and check if output contains the following tokens:
K>* 10.3.0.0/24Show output
Codes: K - kernel route, C - connected, L - local, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, t - Table-Direct, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure VRF LAN: K>* 0.0.0.0/0 [255/8192] unreachable (ICMP unreachable), weight 1, 00:00:06 C>* 10.1.0.0/24 is directly connected, dum0, weight 1, 00:00:06 L>* 10.1.0.1/32 is directly connected, dum0, weight 1, 00:00:06 K>* 10.3.0.0/24 [0/0] via 80.0.0.2, eth0 (vrf WAN), weight 1, 00:00:00
Step 8: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 9: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 10: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.329 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.329/0.329/0.329/0.000 ms
Step 11: Initiate a tcp connection from DUT1 to DUT0 and try to send some messages between both endpoints
admin@DUT0$ monitor test connection server 8080 tcp vrf LAN admin@DUT1$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1
Step 12: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, a999b4dfcd1f2fc9_i 43cd5838b074ba35_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 2s ago, rekeying in 19128s peer-PEER-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 2s ago, rekeying in 3407s, expires in 3958s in cbb3fb3a, 712 bytes, 11 packets, 0s ago out c75d7afb, 764 bytes, 12 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test Site-To-Site With Route Installation And Metrics
Description
In this scenario, DUT0 installs routes with
differents metrics for both IPsec peers. The point is
to check if the routes are installed correctly and most
importantly, whenever the prioritized route is down, the
backup route is used.
Scenario
Step 1: Run command protocols ip show route at DUT0 and check if output does not contain the following tokens:
K>* 10.3.0.0/24Show output
Codes: K - kernel route, C - connected, L - local, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, t - Table-Direct, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure L 192.168.100.100/32 is directly connected, eth0 inactive, weight 1, 00:21:17
Step 2: Set the following configuration in DUT0 :
set interfaces dummy dum0 address 10.1.0.1/24 set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 90.0.0.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX184oCbRAaw6G7NNmGNym5fLWmB1WPnlmec= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 2 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.2 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 route-priority 10 set vpn ipsec site-to-site peer PEER1 auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER1 connection-type respond set vpn ipsec site-to-site peer PEER1 default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER1 ike-group IKE-SA set vpn ipsec site-to-site peer PEER1 local-address 90.0.0.1 set vpn ipsec site-to-site peer PEER1 remote-address 90.0.0.3 set vpn ipsec site-to-site peer PEER1 tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER1 tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER1 tunnel 1 remote prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER1 tunnel 1 route-priority 100
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 0.0.0.0/0 next-hop 80.0.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX1/FyJ+X5PTiXHaUIzO+KxIVmvIQOfd+sEI= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.2 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Set the following configuration in DUT2 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth1 address 90.0.0.3/24 set protocols static route 0.0.0.0/0 next-hop 90.0.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA local auth encrypted-pre-shared-secret U2FsdGVkX18AQrw/vAxCR1VFjANeRYQCSo9fLqCE/Ek= set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 90.0.0.3 set vpn ipsec site-to-site peer PEER remote-address 90.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 5: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.221 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.221/0.221/0.221/0.000 ms
Step 6: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.247 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.247/0.247/0.247/0.000 ms
Step 7: Ping IP address 90.0.0.3 from DUT2:
admin@DUT2$ ping 90.0.0.3 count 1 size 56 timeout 1Show output
PING 90.0.0.3 (90.0.0.3) 56(84) bytes of data. 64 bytes from 90.0.0.3: icmp_seq=1 ttl=64 time=0.035 ms --- 90.0.0.3 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.035/0.035/0.035/0.000 ms
Step 8: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
peer-PEER-tunnel-\d+.+INSTALLEDShow output
vpn-peer-PEER1: #2, ESTABLISHED, IKEv2, b50e0dabe794b102_i 66c0bc9c626c458e_r* local '90.0.0.1' @ 90.0.0.1[500] remote '90.0.0.3' @ 90.0.0.3[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 21270s peer-PEER1-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3420s, expires in 3959s in c1a3d938, 0 bytes, 0 packets out c3f0c894, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24 vpn-peer-PEER: #1, ESTABLISHED, IKEv2, ab312421a45227ad_i 5c4e555b391997a9_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 5s ago, rekeying in 17864s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 5s ago, rekeying in 3429s, expires in 3955s in c96c7d4e, 0 bytes, 0 packets out c0712c99, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24
Step 9: Run command protocols ip show route at DUT0 and check if output contains the following tokens:
K>* 10.3.0.0/24Show output
Codes: K - kernel route, C - connected, L - local, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, t - Table-Direct, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure C>* 10.1.0.0/24 is directly connected, dum0, weight 1, 00:00:11 L>* 10.1.0.1/32 is directly connected, dum0, weight 1, 00:00:11 K * 10.3.0.0/24 [0/100] via 90.0.0.3, eth1, weight 1, 00:00:01 K>* 10.3.0.0/24 [0/10] via 80.0.0.2, eth0, weight 1, 00:00:05 C>* 80.0.0.0/24 is directly connected, eth0, weight 1, 00:00:10 L>* 80.0.0.1/32 is directly connected, eth0, weight 1, 00:00:10 C>* 90.0.0.0/24 is directly connected, eth1, weight 1, 00:00:10 L>* 90.0.0.1/32 is directly connected, eth1, weight 1, 00:00:10 L 192.168.100.100/32 is directly connected, eth0 inactive, weight 1, 00:21:31
Step 10: Run command show system route ip at DUT0 and check if output contains the following tokens:
10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100 10.3.0.0/24 via 80.0.0.2 dev eth0 proto static metric 10Show output
10.1.0.0/24 dev dum0 proto kernel scope link src 10.1.0.1 10.3.0.0/24 via 80.0.0.2 dev eth0 proto static metric 10 10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100 80.0.0.0/24 dev eth0 proto kernel scope link src 80.0.0.1 90.0.0.0/24 dev eth1 proto kernel scope link src 90.0.0.1
Note
The tunnel with the lowest metric configured in the route-priority parameter should be the one used to route the traffic.
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 12: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 13: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.296 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.296/0.296/0.296/0.000 ms
Step 14: Initiate a tcp connection from DUT1 to DUT0 and try to send some messages between both endpoints
admin@DUT0$ monitor test connection server 8080 tcp admin@DUT1$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1
Step 15: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #3, ESTABLISHED, IKEv2, 6315ede7ee23f0fd_i 03557c60015687fa_r* local '80.0.0.1' @ 80.0.0.1[500] remote '80.0.0.2' @ 80.0.0.2[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 3s ago, rekeying in 15661s peer-PEER-tunnel-1: #3, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 3s ago, rekeying in 3465s, expires in 3957s in cb21da80, 816 bytes, 13 packets, 0s ago out c9b4d543, 712 bytes, 11 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24 vpn-peer-PEER1: #2, ESTABLISHED, IKEv2, b50e0dabe794b102_i 66c0bc9c626c458e_r* local '90.0.0.1' @ 90.0.0.1[500] remote '90.0.0.3' @ 90.0.0.3[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 4s ago, rekeying in 21267s peer-PEER1-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 4s ago, rekeying in 3417s, expires in 3956s in c1a3d938, 0 bytes, 0 packets out c3f0c894, 0 bytes, 0 packets local 10.1.0.0/24 remote 10.3.0.0/24
Note
Now we will shutdown the tunnel with the lowest metric from DUT1 and check if the traffic is routed through the backup tunnel.
Step 16: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 17: Run command vpn ipsec clear sa at DUT2 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 18: Run command vpn ipsec initiate peer PEER at DUT2 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 19: Ping IP address 10.1.0.1 from DUT2:
admin@DUT2$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.265 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.265/0.265/0.265/0.000 ms
Step 20: Initiate a tcp connection from DUT2 to DUT0 and try to send some messages between both endpoints
admin@DUT0$ monitor test connection server 8080 tcp admin@DUT2$ monitor test connection client 10.1.0.1 8080 tcp local-address 10.3.0.1
Step 21: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER1: #4, ESTABLISHED, IKEv2, 386932a9712616bc_i 76549c82c67bee3e_r* local '90.0.0.1' @ 90.0.0.1[500] remote '90.0.0.3' @ 90.0.0.3[500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 3s ago, rekeying in 25642s peer-PEER1-tunnel-1: #4, reqid 1, INSTALLED, TUNNEL, ESP:AES_GCM_16-256 installed 3s ago, rekeying in 3338s, expires in 3957s in c073033a, 712 bytes, 11 packets, 0s ago out c1e11bcb, 816 bytes, 13 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Step 22: Run command show system route ip at DUT0 and check if output contains the following tokens:
10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100Show output
10.1.0.0/24 dev dum0 proto kernel scope link src 10.1.0.1 10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100 80.0.0.0/24 dev eth0 proto kernel scope link src 80.0.0.1 90.0.0.0/24 dev eth1 proto kernel scope link src 90.0.0.1
Step 23: Run command show system route ip at DUT0 and check if output does not contain the following tokens:
10.3.0.0/24 via 80.0.0.2 dev eth0 proto static metric 10Show output
10.1.0.0/24 dev dum0 proto kernel scope link src 10.1.0.1 10.3.0.0/24 via 90.0.0.3 dev eth1 proto static metric 100 80.0.0.0/24 dev eth0 proto kernel scope link src 80.0.0.1 90.0.0.0/24 dev eth1 proto kernel scope link src 90.0.0.1