Rtc

This scenario shows how to configure NTP client/server authentication.

../../../../_images/client.svg

Test RTC Synchronization

Description

Checks that RTC is working properly on machines that have an RTC device.

Scenario

Step 1: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 10.100.0.100/24
set protocols static route 0.0.0.0/0 next-hop 10.100.0.50
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system ntp master prefer
set system ntp master stratum 3

Step 2: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 10.100.0.50/24
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Ping IP address 10.100.0.100 from DUT0:

admin@DUT0$ ping 10.100.0.100 count 1 size 56 timeout 1
Show output
PING 10.100.0.100 (10.100.0.100) 56(84) bytes of data.
64 bytes from 10.100.0.100: icmp_seq=1 ttl=64 time=0.405 ms

--- 10.100.0.100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.405/0.405/0.405/0.000 ms

Step 4: Run command set date 2025-09-04 12:00:00 at DUT0 and expect this output: Step 5: Run command set date ntp 10.100.0.100 at DUT0 and check if output does not contain the following tokens:

skipping this server
Show output
Date was successfully updated!

Step 6: Run command show date at DUT0 and check if output does not contain the following tokens:

Thu
Show output
Fri 05 Sep 2025 13:37:03 +00:00

Step 7: Run command set date hwclock from-system debug at DUT0 and expect this output:

Show output
hwclock from util-linux 2.38.1
System Time: 1757079423.741745
Trying to open: /dev/rtc0
Using the rtc interface to the clock.
Last drift adjustment done at 1757079423 seconds after 1969
Last calibration done at 1757079423 seconds after 1969
Hardware clock is on UTC time
Assuming hardware clock is kept in UTC time.
RTC type: 'rtc_cmos'
Using delay: 0.500000 seconds
missed it - 1757079423.742046 is too far past 1757079423.500000 (0.242046 > 0.001000)
1757079424.500000 is close enough to 1757079424.500000 (0.000000 < 0.002000)
Set RTC to 1757079424 (1757079423 + 1; refsystime = 1757079423.000000)
Setting Hardware Clock to 13:37:04 = 1757079424 seconds since 1969
ioctl(RTC_SET_TIME) was successful.
Not adjusting drift factor because the --update-drift option was not used.
New /etc/adjtime data:
0.000000 1757079423 0.000000
1757079423
UTC

Step 8: Run command set date hwclock to-system debug at DUT0 and expect this output:

Show output
hwclock from util-linux 2.38.1
System Time: 1757079424.565655
Trying to open: /dev/rtc0
Using the rtc interface to the clock.
Last drift adjustment done at 1757079423 seconds after 1969
Last calibration done at 1757079423 seconds after 1969
Hardware clock is on UTC time
Assuming hardware clock is kept in UTC time.
Waiting for clock tick...
...got clock tick
Time read from Hardware Clock: 2025/09/05 13:37:05
Hw clock time : 2025/09/05 13:37:05 = 1757079425 seconds since 1969
Time since last adjustment is 2 seconds
Calculated Hardware Clock drift is 0.000000 seconds
Calling settimeofday(NULL, 0) to lock the warp_clock function.
Calling settimeofday(1757079425.000000, NULL) to set the System time.

Step 9: Run command show date at DUT0 and check if output does not contain the following tokens:

Thu
Show output
Fri 05 Sep 2025 13:37:05 +00:00

Test RTC Synchronization With Drift

Description

Tests that RTC is working properly on machines that have an RTC device (while adjusting the drift too).

Scenario

Step 1: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 10.100.0.100/24
set protocols static route 0.0.0.0/0 next-hop 10.100.0.50
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system ntp master prefer
set system ntp master stratum 3

Step 2: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 10.100.0.50/24
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Ping IP address 10.100.0.100 from DUT0:

admin@DUT0$ ping 10.100.0.100 count 1 size 56 timeout 1
Show output
PING 10.100.0.100 (10.100.0.100) 56(84) bytes of data.
64 bytes from 10.100.0.100: icmp_seq=1 ttl=64 time=0.314 ms

--- 10.100.0.100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.314/0.314/0.314/0.000 ms

Step 4: Run command set date 2025-09-04 12:00:00 at DUT0 and expect this output: Step 5: Run command set date ntp 10.100.0.100 at DUT0 and check if output does not contain the following tokens:

skipping this server
Show output
Date was successfully updated!

Step 6: Run command show date at DUT0 and check if output does not contain the following tokens:

Thu
Show output
Fri 05 Sep 2025 13:37:15 +00:00

Step 7: Run command set date hwclock from-system update-drift debug at DUT0 and expect this output:

Show output
hwclock from util-linux 2.38.1
System Time: 1757079435.699447
Trying to open: /dev/rtc0
Using the rtc interface to the clock.
Last drift adjustment done at 1757079435 seconds after 1969
Last calibration done at 1757079435 seconds after 1969
Hardware clock is on UTC time
Assuming hardware clock is kept in UTC time.
Waiting for clock tick...
...got clock tick
Time read from Hardware Clock: 2025/09/05 13:37:16
Hw clock time : 2025/09/05 13:37:16 = 1757079436 seconds since 1969
Time since last adjustment is 1 second
Calculated Hardware Clock drift is 0.000000 seconds
RTC type: 'rtc_cmos'
Using delay: 0.500000 seconds
1757079436.500000 is close enough to 1757079436.500000 (0.000000 < 0.001000)
Set RTC to 1757079436 (1757079436 + 0; refsystime = 1757079436.000000)
Setting Hardware Clock to 13:37:16 = 1757079436 seconds since 1969
ioctl(RTC_SET_TIME) was successful.
Not adjusting drift factor because it has been less than four hours since the last calibration.
New /etc/adjtime data:
0.000000 1757079436 0.000000
1757079436
UTC

Step 8: Run command set date hwclock to-system debug at DUT0 and expect this output:

Show output
hwclock from util-linux 2.38.1
System Time: 1757079436.580922
Trying to open: /dev/rtc0
Using the rtc interface to the clock.
Last drift adjustment done at 1757079436 seconds after 1969
Last calibration done at 1757079436 seconds after 1969
Hardware clock is on UTC time
Assuming hardware clock is kept in UTC time.
Waiting for clock tick...
...got clock tick
Time read from Hardware Clock: 2025/09/05 13:37:17
Hw clock time : 2025/09/05 13:37:17 = 1757079437 seconds since 1969
Time since last adjustment is 1 second
Calculated Hardware Clock drift is 0.000000 seconds
Calling settimeofday(NULL, 0) to lock the warp_clock function.
Calling settimeofday(1757079437.000000, NULL) to set the System time.

Step 9: Run command show date at DUT0 and check if output does not contain the following tokens:

Thu
Show output
Fri 05 Sep 2025 13:37:17 +00:00