Check Sending Notifications

This scenario shows how to configure a trap-target to send coldStart notifications and specifying the source address to be used in those notifications. In addition, the SNMP service snmp monitor traps command is checked.

../../../../_images/dummy.svg

Test SNMP Send Traps

Description

A trap-target is configured to send coldStart traps for a user in DUT0 and the monitor command is used to check sending notifications in SNMPv3. Setting local-address to DUT0 specifies the source address to use in sent notifications.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 20.0.0.1/24
set interfaces ethernet eth0 address 10.0.0.1/24
set service snmp engine-id 0x80000009010a0101c1
set service snmp trap-target 10.0.0.2 version v3 user USER2TEST
set service snmp user USER2TEST
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 10.0.0.2/24
set protocols static route 20.0.0.0/24 next-hop 10.0.0.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Initially, the source address used in notifications is the one corresponding to the interface through which they are sent (10.0.0.1).

Step 3: Run command service snmp monitor traps user USER2TEST engine-id 0x80000009010a0101c1 at DUT1.

Step 4: Modify the following configuration lines in DUT0 :

set system location Teldat_Spain

Note

After setting the local-address in DUT0, the source address used in notifications will be the one specified in this setting (20.0.0.1).

Step 5: Modify the following configuration lines in DUT0 :

set service snmp local-address 20.0.0.1

Step 6: Run command service snmp monitor traps user USER2TEST engine-id 0x80000009010a0101c1 at DUT1.

Step 7: Modify the following configuration lines in DUT0 :

delete system location

Test SNMP Send Informs

Description

A trap-target is configured to send coldStart informs for a user in DUT0 and the monitor command is used to check sending notifications in SNMPv3. Setting local-address to DUT0 specifies the source address to use in sent notifications.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 20.0.0.1/24
set interfaces ethernet eth0 address 10.0.0.1/24
set service snmp engine-id 0x80000009010a0101c1
set service snmp trap-target 10.0.0.2 version v3 type inform
set service snmp trap-target 10.0.0.2 version v3 user USER2TEST
set service snmp user USER2TEST
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 10.0.0.2/24
set protocols static route 20.0.0.0/24 next-hop 10.0.0.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Initially, the source address used in notifications is the one corresponding to the interface through which they are sent (10.0.0.1).

Step 3: Run command service snmp monitor traps user USER2TEST at DUT1.

Step 4: Modify the following configuration lines in DUT0 :

set system location Teldat_Spain

Note

After setting the local-address in DUT0, the source address used in notifications will be the one specified in this setting (20.0.0.1).

Step 5: Modify the following configuration lines in DUT0 :

set service snmp local-address 20.0.0.1

Step 6: Run command service snmp monitor traps user USER2TEST at DUT1.

Step 7: Modify the following configuration lines in DUT0 :

delete system location