Roadwarrior
This scenario shows different ways to setup a roadwarrior VPN connection; in which, instead of using a N2N (network to network) connection, a single machine (e.g., a host) is able to connect to a remote private network.
On the one hand, DUT2 and DUT0 represent a remote branch
office. On the other hand, DUT1 is a roadwarrior that can
establish a connection to DUT2 using different virtual IPs.
Note that security associations (SAs) have to be manually
flushed with the command clear vpn ipsec sa. Depending on
the configuration parameter connection-type, the new tunnel
connections will be created or not.
Test VPN Roadwarrior Connection With VTI
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 10.1.0.1/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA global-secrets ike-psk %any encrypted-secret U2FsdGVkX18JEj8mx2DYJmpo7SjsYsHFenLHCmtnR8k= set vpn ipsec auth-profile AUTH-SA local auth ike-psk id %any set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER vti local prefix 10.1.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 10.1.0.0/24 interface eth0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA global-secrets ike-psk %any encrypted-secret U2FsdGVkX1+Jv1p/acpTgVrF7gyvB4f+DfhF1MqVjgE= set vpn ipsec auth-profile AUTH-SA local auth ike-psk id %any set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 1 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.220 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.220/0.220/0.220/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.203 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.203/0.203/0.203/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.304 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.304/0.304/0.304/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::7c76:24ff:fe91:552a/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.295 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.295/0.295/0.295/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.489 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.489/0.489/0.489/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, dfb435ef5b6ae472_i 83513e25fa52cd49_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 26560s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3308s, expires in 3959s in ce011754 (0x90000000), 168 bytes, 2 packets, 0s ago out cdec9dc0 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 12: Modify the following configuration lines in DUT1 :
delete interfaces dummy dum0 address 10.3.0.1/24 set interfaces dummy dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::7c76:24ff:fe91:552a/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.287 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.287/0.287/0.287/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.456 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.456/0.456/0.456/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, 4708ca8a05b53177_i d9fe3a78dd37c569_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 27410s peer-PEER-tunnel-VTI: #2, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3490s, expires in 3960s in c03abdd4 (0x90000000), 168 bytes, 2 packets, 0s ago out c0bca9f9 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 0.0.0.0/0
Test VPN Roadwarrior Connection With Global Policies
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 10.1.0.1/24 set protocols static route 10.3.0.0/24 interface eth0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA global-secrets ike-psk %any encrypted-secret U2FsdGVkX19latAZ+j+REDgenliMkRTWBSVXXO4UeX0= set vpn ipsec auth-profile AUTH-SA local auth ike-psk id %any set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 local prefix 10.1.0.0/24 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.3.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 address 10.3.0.1/24 set interfaces ethernet eth0 address 80.0.0.2/24 set protocols static route 10.1.0.0/24 interface eth0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA global-secrets ike-psk %any encrypted-secret U2FsdGVkX1+UgsE7RHhVbi7YQGPiNxW1/kCK7q5H3zE= set vpn ipsec auth-profile AUTH-SA local auth ike-psk id %any set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 1 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.235 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.235/0.235/0.235/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.256 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.256/0.256/0.256/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.349 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.349/0.349/0.349/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/24 up up fe80::e4bc:11ff:fefe:b223/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.266 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.266/0.266/0.266/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.511 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.511/0.511/0.511/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, dd71726347087dbb_i 2647fc1f9b8c60da_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 27911s peer-PEER-tunnel-1: #1, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3256s, expires in 3959s in c8f68f7c, 168 bytes, 2 packets, 0s ago out c1fc56c1, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Step 11: Run command vpn ipsec clear sa at DUT1 and expect this output:
Show output
Deleting IPSec SAs... 100.0% Closed tunnels: 1
Step 12: Modify the following configuration lines in DUT1 :
delete interfaces dummy dum0 address 10.3.0.1/24 set interfaces dummy dum0 address 10.3.0.2/24
Step 13: Run command vpn ipsec initiate peer PEER at DUT1 and expect this output:
Show output
Initiating IPSec SAs... 0.0% Initiated tunnels: 1
Step 14: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.2/24 up up fe80::e4bc:11ff:fefe:b223/64
Step 15: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.280 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.280/0.280/0.280/0.000 ms
Step 16: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.2 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.451 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.451/0.451/0.451/0.000 ms
Step 17: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #2, ESTABLISHED, IKEv2, a49e740c088f2380_i fc07ae2b15fe74a3_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 0s ago, rekeying in 25663s peer-PEER-tunnel-1: #2, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 0s ago, rekeying in 3286s, expires in 3960s in c13a66de, 168 bytes, 2 packets, 0s ago out c5d7adb5, 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.0/24
Test VPN Roadwarrior Connection With VTI And VIPs Pool
Description
In this scenario, DUT0 uses a VTI
interface to encapsulate the VPN traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 10.1.0.1/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA global-secrets ike-psk %any encrypted-secret U2FsdGVkX1+5eZoXESNOJ52KG7YeVnMGvaTxzoXXnUM= set vpn ipsec auth-profile AUTH-SA local auth ike-psk id %any set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec site-to-site peer PEER vti local prefix 10.1.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 set interfaces ethernet eth0 address 80.0.0.2/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA global-secrets ike-psk %any encrypted-secret U2FsdGVkX19zGjAaSuzX7N3TFFzSY/FJ7hd/TNIF1cc= set vpn ipsec auth-profile AUTH-SA local auth ike-psk id %any set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 1 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.238 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.238/0.238/0.238/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.239 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.239/0.239/0.239/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.287 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.287/0.287/0.287/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::a0bb:60ff:feaa:8954/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.329 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.329/0.329/0.329/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.443 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.443/0.443/0.443/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 40f46f68850764be_i 97b7fcf65d134b86_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 27791s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3469s, expires in 3959s in cd4a97f2 (0x90000000), 168 bytes, 2 packets, 1s ago out cf2f458a (0x90000000), 168 bytes, 2 packets, 1s ago local 10.1.0.0/24 remote 10.3.0.1/32
Test VPN Roadwarrior Connection With Global Policies And VIPs Pool
Description
In this scenario, DUT0 uses global VPN
policies (or selectors) to encapsulate traffic.
DUT1 requests a virtual IP address from
DUT0 and it installed in dum0. Routes are
also automatically installed taking into
account the negotiated selectors.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.1.0.2/24 set protocols static route 0.0.0.0/0 next-hop 10.1.0.1 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 80.0.0.1/24 set interfaces ethernet eth1 address 10.1.0.1/24 set interfaces vti vti0 ipsec PEER set interfaces vti vti0 local-address 80.0.0.1 set interfaces vti vti0 remote-address 0.0.0.0 set protocols static route 10.3.0.0/24 interface vti0 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set vpn ipsec auth-profile AUTH-SA global-secrets ike-psk %any encrypted-secret U2FsdGVkX1/uEx1I0Kj5Gmd6l2H8rN8RDIxpAvfu11M= set vpn ipsec auth-profile AUTH-SA local auth ike-psk id %any set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec pool POOL prefix 10.3.0.0/24 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type respond set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER local-address 80.0.0.1 set vpn ipsec site-to-site peer PEER pool POOL set vpn ipsec site-to-site peer PEER vti local prefix 10.1.0.0/24
Step 3: Set the following configuration in DUT1 :
set interfaces dummy dum0 set interfaces ethernet eth0 address 80.0.0.2/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0' set system vrf main set vpn ipsec auth-profile AUTH-SA global-secrets ike-psk %any encrypted-secret U2FsdGVkX1+SlGHW+b1Z3OkNLUubq9JiBBrdiItL3hI= set vpn ipsec auth-profile AUTH-SA local auth ike-psk id %any set vpn ipsec esp-group CHILD-SA mode tunnel set vpn ipsec esp-group CHILD-SA proposal 1 encryption aes256gcm128 set vpn ipsec esp-group CHILD-SA proposal 1 pfs dh-group19 set vpn ipsec ike-group IKE-SA key-exchange ikev2 set vpn ipsec ike-group IKE-SA proposal 1 dh-group 19 set vpn ipsec ike-group IKE-SA proposal 1 encryption aes256gcm128 set vpn ipsec ike-group IKE-SA proposal 1 hash sha256 set vpn ipsec logging log-types any log-level 1 set vpn ipsec site-to-site peer PEER auth-profile AUTH-SA set vpn ipsec site-to-site peer PEER connection-type initiate set vpn ipsec site-to-site peer PEER default-esp-group CHILD-SA set vpn ipsec site-to-site peer PEER ike-group IKE-SA set vpn ipsec site-to-site peer PEER install-vips interface dum0 set vpn ipsec site-to-site peer PEER remote-address 80.0.0.1 set vpn ipsec site-to-site peer PEER tunnel 1 install-routes main set vpn ipsec site-to-site peer PEER tunnel 1 remote prefix 10.1.0.0/24
Step 4: Ping IP address 80.0.0.1 from DUT1:
admin@DUT1$ ping 80.0.0.1 count 1 size 56 timeout 1Show output
PING 80.0.0.1 (80.0.0.1) 56(84) bytes of data. 64 bytes from 80.0.0.1: icmp_seq=1 ttl=64 time=0.229 ms --- 80.0.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.229/0.229/0.229/0.000 ms
Step 5: Ping IP address 80.0.0.2 from DUT0:
admin@DUT0$ ping 80.0.0.2 count 1 size 56 timeout 1Show output
PING 80.0.0.2 (80.0.0.2) 56(84) bytes of data. 64 bytes from 80.0.0.2: icmp_seq=1 ttl=64 time=0.311 ms --- 80.0.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.311/0.311/0.311/0.000 ms
Step 6: Ping IP address 10.1.0.2 from DUT0:
admin@DUT0$ ping 10.1.0.2 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=64 time=0.368 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.368/0.368/0.368/0.000 ms
Step 7: Run command interfaces dummy dum0 show at DUT1 and expect this output:
Show output
----------------------------------------------------------------- Name IP Address Admin Oper Vrf Description ----------------------------------------------------------------- dum0 10.3.0.1/32 up up fe80::4cb6:e1ff:fe2d:cd0d/64
Step 8: Ping IP address 10.1.0.1 from DUT1:
admin@DUT1$ ping 10.1.0.1 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.1 (10.1.0.1) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=0.292 ms --- 10.1.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.292/0.292/0.292/0.000 ms
Step 9: Ping IP address 10.1.0.2 from DUT1:
admin@DUT1$ ping 10.1.0.2 local-address 10.3.0.1 count 1 size 56 timeout 1Show output
PING 10.1.0.2 (10.1.0.2) from 10.3.0.1 : 56(84) bytes of data. 64 bytes from 10.1.0.2: icmp_seq=1 ttl=63 time=0.455 ms --- 10.1.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.455/0.455/0.455/0.000 ms
Step 10: Run command vpn ipsec show sa at DUT0 and check if output matches the following regular expressions:
[1-9]\d? packetsShow output
vpn-peer-PEER: #1, ESTABLISHED, IKEv2, 7c4b111e984725fa_i cd36be102723b8db_r* local '80.0.0.1' @ 80.0.0.1[4500] remote '80.0.0.2' @ 80.0.0.2[4500] [10.3.0.1] AES_GCM_16-256/PRF_HMAC_SHA2_256/ECP_256 established 1s ago, rekeying in 17187s peer-PEER-tunnel-VTI: #1, reqid 1, INSTALLED, TUNNEL-in-UDP, ESP:AES_GCM_16-256 installed 1s ago, rekeying in 3247s, expires in 3959s in c60823ae (0x90000000), 168 bytes, 2 packets, 0s ago out c5c07c69 (0x90000000), 168 bytes, 2 packets, 0s ago local 10.1.0.0/24 remote 10.3.0.1/32