Bfd Ospf

Test to check BFD protocol in OSPF.

Test Connection

Description

Tests connection between two devices with BFD in OSPF by checking if they are each others peers and their status is up.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.1.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 3: Ping IP address 192.168.1.2 from DUT0:

admin@DUT0$ ping 192.168.1.2 count 1 size 56 timeout 1

Show output

PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.369 ms

--- 192.168.1.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.369/0.369/0.369/0.000 ms

Step 4: Ping IP address 192.168.1.1 from DUT1:

admin@DUT1$ ping 192.168.1.1 count 1 size 56 timeout 1

Show output

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.259 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.259/0.259/0.259/0.000 ms

Note

Check that they are each other’s neighbors

Step 5: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

2.2.2.2

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
2.2.2.2           1 Full/-          0.892s            39.106s 192.168.1.2     eth0:192.168.1.1                     1     0     0

Step 6: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

1.1.1.1

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          0.973s            37.352s 192.168.1.1     eth0:192.168.1.2                     1     0     0

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established)

Step 7: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

192.168.1.2
Status: up

Show output

BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 692802939
                Remote ID: 365654903
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 8: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

192.168.1.1
Status: up

Show output

BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 365654903
                Remote ID: 692802939
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

---

Test Connection With Three Devices

Description

Tests connection between three devices with BFD in OSPF by checking if they are each others peers and their status is up.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.2.1/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf area 1 network 192.168.2.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.2.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.3.2/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 1 network 192.168.2.0/24
set protocols ospf area 2 network 192.168.3.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Set the following configuration in DUT2 :

set interfaces dummy dum0 address 10.0.0.3/24
set interfaces ethernet eth0 address 192.168.1.3/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.3.3/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf area 2 network 192.168.3.0/24
set protocols ospf parameters router-id 3.3.3.3
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 4: Ping IP address 192.168.1.3 from DUT0:

admin@DUT0$ ping 192.168.1.3 count 1 size 56 timeout 1

Show output

PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data.
64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.252 ms

--- 192.168.1.3 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.252/0.252/0.252/0.000 ms

Step 5: Ping IP address 192.168.2.2 from DUT0:

admin@DUT0$ ping 192.168.2.2 count 1 size 56 timeout 1

Show output

PING 192.168.2.2 (192.168.2.2) 56(84) bytes of data.
64 bytes from 192.168.2.2: icmp_seq=1 ttl=64 time=0.433 ms

--- 192.168.2.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.433/0.433/0.433/0.000 ms

Step 6: Ping IP address 192.168.2.1 from DUT1:

admin@DUT1$ ping 192.168.2.1 count 1 size 56 timeout 1

Show output

PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
64 bytes from 192.168.2.1: icmp_seq=1 ttl=64 time=0.239 ms

--- 192.168.2.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.239/0.239/0.239/0.000 ms

Step 7: Ping IP address 192.168.3.3 from DUT1:

admin@DUT1$ ping 192.168.3.3 count 1 size 56 timeout 1

Show output

PING 192.168.3.3 (192.168.3.3) 56(84) bytes of data.
64 bytes from 192.168.3.3: icmp_seq=1 ttl=64 time=0.248 ms

--- 192.168.3.3 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.248/0.248/0.248/0.000 ms

Step 8: Ping IP address 192.168.1.1 from DUT2:

admin@DUT2$ ping 192.168.1.1 count 1 size 56 timeout 1

Show output

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.243 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.243/0.243/0.243/0.000 ms

Step 9: Ping IP address 192.168.3.2 from DUT2:

admin@DUT2$ ping 192.168.3.2 count 1 size 56 timeout 1

Show output

PING 192.168.3.2 (192.168.3.2) 56(84) bytes of data.
64 bytes from 192.168.3.2: icmp_seq=1 ttl=64 time=0.219 ms

--- 192.168.3.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.219/0.219/0.219/0.000 ms

Note

Check that they are each other’s neighbors

Step 10: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

2.2.2.2
3.3.3.3

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
3.3.3.3           1 Init/-          9.185s            30.814s 192.168.1.3     eth0:192.168.1.1                     0     0     0
2.2.2.2           1 Full/-          1.157s            38.841s 192.168.2.2     eth1:192.168.2.1                     1     0     0

Step 11: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

1.1.1.1
3.3.3.3

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          1.246s            36.540s 192.168.2.1     eth0:192.168.2.2                     1     0     0
3.3.3.3           1 Full/-          1.245s            30.725s 192.168.3.3     eth1:192.168.3.2                     1     0     0

Step 12: Run command protocols ospf show neighbor at DUT2 and check if output matches the following regular expressions:

1.1.1.1
2.2.2.2

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          1.898s            38.100s 192.168.1.1     eth0:192.168.1.3                     1     0     0
2.2.2.2           1 Full/-          9.685s            30.313s 192.168.3.2     eth1:192.168.3.3                     0     0     0

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established)

Step 13: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

192.168.1.3
Status: up
192.168.2.2
Status: up

Show output

BFD Peers:
        peer 192.168.1.3 vrf default interface eth0
                ID: 1866279720
                Remote ID: 180154392
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

        peer 192.168.2.2 vrf default interface eth1
                ID: 148412208
                Remote ID: 3241211823
                Active mode
                Status: up
                Uptime: 8 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 14: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

192.168.2.1
Status: up
192.168.3.3
Status: up

Show output

BFD Peers:
        peer 192.168.2.1 vrf default interface eth0
                ID: 3241211823
                Remote ID: 148412208
                Active mode
                Status: up
                Uptime: 8 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

        peer 192.168.3.3 vrf default interface eth1
                ID: 2318790794
                Remote ID: 2816448129
                Active mode
                Status: up
                Uptime: 9 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 15: Run command protocols bfd show peers at DUT2 and check if output matches the following regular expressions:

192.168.1.1
Status: up
192.168.3.2
Status: up

Show output

BFD Peers:
        peer 192.168.3.2 vrf default interface eth1
                ID: 2816448129
                Remote ID: 2318790794
                Active mode
                Status: up
                Uptime: 9 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

        peer 192.168.1.1 vrf default interface eth0
                ID: 180154392
                Remote ID: 1866279720
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

---

Test Profile

Description

Checks that all BFD profile configured parameters are shown.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols bfd profile PFL detect-multiplier 5
set protocols bfd profile PFL echo-interval 60
set protocols bfd profile PFL echo-mode
set protocols bfd profile PFL passive-mode
set protocols bfd profile PFL receive-interval 400
set protocols bfd profile PFL transmit-interval 400
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Modify the following configuration lines in DUT0 :

set interfaces ethernet eth0 ip ospf bfd profile PFL

Step 3: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.1.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 4: Ping IP address 192.168.1.2 from DUT0:

admin@DUT0$ ping 192.168.1.2 count 1 size 56 timeout 1

Show output

PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.326 ms

--- 192.168.1.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.326/0.326/0.326/0.000 ms

Step 5: Ping IP address 192.168.1.1 from DUT1:

admin@DUT1$ ping 192.168.1.1 count 1 size 56 timeout 1

Show output

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.225 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.225/0.225/0.225/0.000 ms

Note

Check that they are each other’s neighbors

Step 6: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

192.168.1.2

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
2.2.2.2           1 Full/-          0.724s            39.274s 192.168.1.2     eth0:192.168.1.1                     1     0     0

Step 7: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

192.168.1.1

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          0.799s            36.514s 192.168.1.1     eth0:192.168.1.2                     1     0     0

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established). Check that all configureed profile parameters are shown in DUT0

Step 8: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

192.168.1.2
Status: up
Detect-multiplier: 5
Echo receive interval: 60ms
Echo transmission interval: 60ms
Passive mode
Receive interval: 400ms
Transmission interval: 400ms

Show output

BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 3870016751
                Remote ID: 1509608576
                Passive mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 190/220/251 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 9: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

192.168.1.1
Status: up

Show output

BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 1509608576
                Remote ID: 3870016751
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms

---