Bfd Ospf

Test to check BFD protocol in OSPF.

Test Connection

Description

Tests connection between two devices with BFD in OSPF by checking if they are each others peers and their status is up.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.1.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 3: Ping IP address 192.168.1.2 from DUT0:

admin@DUT0$ ping 192.168.1.2 count 1 size 56 timeout 1

Show output

PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.213 ms

--- 192.168.1.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.213/0.213/0.213/0.000 ms

Step 4: Ping IP address 192.168.1.1 from DUT1:

admin@DUT1$ ping 192.168.1.1 count 1 size 56 timeout 1

Show output

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.249 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.249/0.249/0.249/0.000 ms

Note

Check that they are each other’s neighbors

Step 5: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

2.2.2.2

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
2.2.2.2           1 Init/-          0.348s            39.651s 192.168.1.2     eth0:192.168.1.1                     0     0     0

Step 6: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

1.1.1.1

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          0.237s            39.761s 192.168.1.1     eth0:192.168.1.2                     1     0     0

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established)

Step 7: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

192.168.1.2
Status: up

Show output

BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 3621029385
                Remote ID: 1655346474
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 8: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

192.168.1.1
Status: up

Show output

BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 1655346474
                Remote ID: 3621029385
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

---

Test Connection With Three Devices

Description

Tests connection between three devices with BFD in OSPF by checking if they are each others peers and their status is up.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.2.1/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf area 1 network 192.168.2.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.2.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.3.2/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 1 network 192.168.2.0/24
set protocols ospf area 2 network 192.168.3.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Set the following configuration in DUT2 :

set interfaces dummy dum0 address 10.0.0.3/24
set interfaces ethernet eth0 address 192.168.1.3/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set interfaces ethernet eth1 address 192.168.3.3/24
set interfaces ethernet eth1 ip ospf bfd
set interfaces ethernet eth1 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf area 2 network 192.168.3.0/24
set protocols ospf parameters router-id 3.3.3.3
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 4: Ping IP address 192.168.1.3 from DUT0:

admin@DUT0$ ping 192.168.1.3 count 1 size 56 timeout 1

Show output

PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data.
64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.358 ms

--- 192.168.1.3 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.358/0.358/0.358/0.000 ms

Step 5: Ping IP address 192.168.2.2 from DUT0:

admin@DUT0$ ping 192.168.2.2 count 1 size 56 timeout 1

Show output

PING 192.168.2.2 (192.168.2.2) 56(84) bytes of data.
64 bytes from 192.168.2.2: icmp_seq=1 ttl=64 time=0.489 ms

--- 192.168.2.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.489/0.489/0.489/0.000 ms

Step 6: Ping IP address 192.168.2.1 from DUT1:

admin@DUT1$ ping 192.168.2.1 count 1 size 56 timeout 1

Show output

PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
64 bytes from 192.168.2.1: icmp_seq=1 ttl=64 time=0.495 ms

--- 192.168.2.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.495/0.495/0.495/0.000 ms

Step 7: Ping IP address 192.168.3.3 from DUT1:

admin@DUT1$ ping 192.168.3.3 count 1 size 56 timeout 1

Show output

PING 192.168.3.3 (192.168.3.3) 56(84) bytes of data.
64 bytes from 192.168.3.3: icmp_seq=1 ttl=64 time=0.378 ms

--- 192.168.3.3 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.378/0.378/0.378/0.000 ms

Step 8: Ping IP address 192.168.1.1 from DUT2:

admin@DUT2$ ping 192.168.1.1 count 1 size 56 timeout 1

Show output

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.399 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.399/0.399/0.399/0.000 ms

Step 9: Ping IP address 192.168.3.2 from DUT2:

admin@DUT2$ ping 192.168.3.2 count 1 size 56 timeout 1

Show output

PING 192.168.3.2 (192.168.3.2) 56(84) bytes of data.
64 bytes from 192.168.3.2: icmp_seq=1 ttl=64 time=0.533 ms

--- 192.168.3.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.533/0.533/0.533/0.000 ms

Note

Check that they are each other’s neighbors

Step 10: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

2.2.2.2
3.3.3.3

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
3.3.3.3           1 Init/-          1.449s            38.550s 192.168.1.3     eth0:192.168.1.1                     0     0     0
2.2.2.2           1 Full/-          3.689s            36.309s 192.168.2.2     eth1:192.168.2.1                     1     0     0

Step 11: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

1.1.1.1
3.3.3.3

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          3.775s            34.059s 192.168.2.1     eth0:192.168.2.2                     1     0     0
3.3.3.3           1 Full/-          1.534s            38.464s 192.168.3.3     eth1:192.168.3.2                     1     0     0

Step 12: Run command protocols ospf show neighbor at DUT2 and check if output matches the following regular expressions:

1.1.1.1
2.2.2.2

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          0.185s            39.813s 192.168.1.1     eth0:192.168.1.3                     1     0     0
2.2.2.2           1 Full/-          5.780s            31.977s 192.168.3.2     eth1:192.168.3.3                     1     0     0

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established)

Step 13: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

192.168.1.3
Status: up
192.168.2.2
Status: up

Show output

BFD Peers:
        peer 192.168.1.3 vrf default interface eth0
                ID: 1327762997
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

        peer 192.168.2.2 vrf default interface eth1
                ID: 3451229665
                Remote ID: 3321921001
                Active mode
                Status: up
                Uptime: 7 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 14: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

192.168.2.1
Status: up
192.168.3.3
Status: up

Show output

BFD Peers:
        peer 192.168.2.1 vrf default interface eth0
                ID: 3321921001
                Remote ID: 3451229665
                Active mode
                Status: up
                Uptime: 7 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

        peer 192.168.3.3 vrf default interface eth1
                ID: 660522534
                Remote ID: 3548414922
                Active mode
                Status: up
                Uptime: 4 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 15: Run command protocols bfd show peers at DUT2 and check if output matches the following regular expressions:

192.168.1.1
Status: up
192.168.3.2
Status: up

Show output

BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 1092391070
                Remote ID: 0
                Active mode
                Status: down
                Downtime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 1000ms
                        Transmission interval: 1000ms
                        Echo receive interval: disabled

        peer 192.168.3.2 vrf default interface eth1
                ID: 3548414922
                Remote ID: 660522534
                Active mode
                Status: up
                Uptime: 4 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

---

Test Profile

Description

Checks that all BFD profile configured parameters are shown.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address 10.0.0.1/24
set interfaces ethernet eth0 address 192.168.1.1/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols bfd profile PFL detect-multiplier 5
set protocols bfd profile PFL echo-interval 60
set protocols bfd profile PFL echo-mode
set protocols bfd profile PFL passive-mode
set protocols bfd profile PFL receive-interval 400
set protocols bfd profile PFL transmit-interval 400
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 1.1.1.1
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Modify the following configuration lines in DUT0 :

set interfaces ethernet eth0 ip ospf bfd profile PFL

Step 3: Set the following configuration in DUT1 :

set interfaces dummy dum0 address 10.0.0.2/24
set interfaces ethernet eth0 address 192.168.1.2/24
set interfaces ethernet eth0 ip ospf bfd
set interfaces ethernet eth0 ip ospf network point-to-point
set protocols ospf area 0 network 10.0.0.0/24
set protocols ospf area 0 network 192.168.1.0/24
set protocols ospf parameters router-id 2.2.2.2
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 4: Ping IP address 192.168.1.2 from DUT0:

admin@DUT0$ ping 192.168.1.2 count 1 size 56 timeout 1

Show output

PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.366 ms

--- 192.168.1.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.366/0.366/0.366/0.000 ms

Step 5: Ping IP address 192.168.1.1 from DUT1:

admin@DUT1$ ping 192.168.1.1 count 1 size 56 timeout 1

Show output

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.247 ms

--- 192.168.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.247/0.247/0.247/0.000 ms

Note

Check that they are each other’s neighbors

Step 6: Run command protocols ospf show neighbor at DUT0 and check if output matches the following regular expressions:

192.168.1.2

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
2.2.2.2           1 Full/-          0.728s            39.270s 192.168.1.2     eth0:192.168.1.1                     1     0     0

Step 7: Run command protocols ospf show neighbor at DUT1 and check if output matches the following regular expressions:

192.168.1.1

Show output

Neighbor ID     Pri State           Up Time         Dead Time Address         Interface                        RXmtL RqstL DBsmL
1.1.1.1           1 Full/-          0.799s            37.277s 192.168.1.1     eth0:192.168.1.2                     1     0     0

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established). Check that all configureed profile parameters are shown in DUT0

Step 8: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

192.168.1.2
Status: up
Detect-multiplier: 5
Echo receive interval: 60ms
Echo transmission interval: 60ms
Passive mode
Receive interval: 400ms
Transmission interval: 400ms

Show output

BFD Peers:
        peer 192.168.1.2 vrf default interface eth0
                ID: 4018959097
                Remote ID: 2546085159
                Passive mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 139/204/292 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms
                        Echo transmission interval: 60ms
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 9: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

192.168.1.1
Status: up

Show output

BFD Peers:
        peer 192.168.1.1 vrf default interface eth0
                ID: 2546085159
                Remote ID: 4018959097
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: 60ms

---