Bfd Static Route6

Tests to check BFD protocol in static routes for IPv6.

../../../../_images/bfdstaticroute6.svg

Test Connection With Next Hop IPv6

Description

Tests connection between two devices with BFD in static routes using the gateway as the BFD peer, checking if they are each others peers and their status is up and installed.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '::/0' next-hop '3fff:10::200' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 3: Ping IP address 3fff:10::200 from DUT0:

admin@DUT0$ ping 3fff:10::200 count 1 size 56 timeout 1
Show output
PING 3fff:10::200(3fff:10::200) 56 data bytes
64 bytes from 3fff:10::200: icmp_seq=1 ttl=64 time=278 ms

--- 3fff:10::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 278.048/278.048/278.048/0.000 ms

Step 4: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=64 time=0.482 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.482/0.482/0.482/0.000 ms

Note

Check that the operational command ‘protocols bfd show static route’ works, and shows that they are each other’s peers and that their status is installed, indicating that the next-hop router is reachable

Step 5: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

3fff:10::200
status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: installed)

Step 6: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

3fff:10::100
status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: installed)

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established)

Step 7: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

3fff:10::200
Status: up
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 2146077468
                Remote ID: 4185981498
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 8: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

3fff:10::100
Status: up
Show output
BFD Peers:
        peer 3fff:10::100 vrf default
                ID: 4185981498
                Remote ID: 2146077468
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Test Connection With Next Hop And Interface IPv6

Description

Tests connection between two devices with BFD in static routes using the gateway as the BFD peer and an interface, checking if they are each others peers and their status is up and installed.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '::/0' next-hop '3fff:10::200' interface eth0 bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' interface eth0 bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 3: Ping IP address 3fff:10::200 from DUT0:

admin@DUT0$ ping 3fff:10::200 count 1 size 56 timeout 1
Show output
PING 3fff:10::200(3fff:10::200) 56 data bytes
64 bytes from 3fff:10::200: icmp_seq=1 ttl=64 time=237 ms

--- 3fff:10::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 236.736/236.736/236.736/0.000 ms

Step 4: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=64 time=0.472 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.472/0.472/0.472/0.000 ms

Note

Check that the operational command ‘protocols bfd show static route’ works, and shows that they are each other’s peers and that their status is installed, indicating that the next-hop router is reachable

Step 5: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

3fff:10::200
status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: installed)

Step 6: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

3fff:10::100
status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: installed)

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established)

Step 7: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

3fff:10::200
Status: up
Show output
BFD Peers:
        peer 3fff:10::200 vrf default interface eth0
                ID: 664917671
                Remote ID: 1801434087
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 8: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

3fff:10::100
Status: up
Show output
BFD Peers:
        peer 3fff:10::100 vrf default interface eth0
                ID: 1801434087
                Remote ID: 664917671
                Active mode
                Status: up
                Uptime: 2 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Test Connection With Next Hop And Next Hop VRF IPv6

Description

Tests connection between two devices with BFD in static routes using the gateway as the BFD peer and a leaked route with a nexthop in the specified VRF ID, checking if they are each others peers and their status is up and installed.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set interfaces ethernet eth0 vrf VRF
set protocols static route6 '::/0' next-hop '3fff:10::200' next-hop-vrf VRF bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf VRF

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set interfaces ethernet eth0 vrf VRF
set protocols static route6 '::/0' next-hop '3fff:10::100' next-hop-vrf VRF bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
set system vrf VRF

Note

Check connectivity

Step 3: Ping IP address 3fff:10::200 from DUT0:

admin@DUT0$ ping 3fff:10::200 count 1 size 56 timeout 1
Show output
PING 3fff:10::200(3fff:10::200) 56 data bytes
64 bytes from 3fff:10::200: icmp_seq=1 ttl=64 time=0.200 ms

--- 3fff:10::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.200/0.200/0.200/0.000 ms

Step 4: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=64 time=0.372 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.372/0.372/0.372/0.000 ms

Note

Check that the operational command ‘protocols bfd show static route’ works, and shows that they are each other’s peers and that their status is installed, indicating that the next-hop router is reachable

Step 5: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

3fff:10::200
status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::200 (status: installed)

Step 6: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

3fff:10::100
status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        ::/0 peer 3fff:10::100 (status: installed)

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established)

Step 7: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

3fff:10::200
Status: up
Show output
BFD Peers:
        peer 3fff:10::200 vrf VRF
                ID: 2582898382
                Remote ID: 3095241649
                Active mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 8: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

3fff:10::100
Status: up
Show output
BFD Peers:
        peer 3fff:10::100 vrf VRF
                ID: 3095241649
                Remote ID: 2582898382
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Test Multihop Connection IPv6

Description

Tests multihop connection between two devices in different networks using a third device connected to both networks, checking if they are each others peers and their status is up and installed.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces dummy dum0 address '3fff:1::1/64'
set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '3fff:20::/64' next-hop '3fff:10::101'
set protocols static route6 '3fff:2::/64' next-hop '3fff:20::200' bfd multihop
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces dummy dum0 address '3fff:2::1/64'
set interfaces ethernet eth0 address '3fff:20::200/64'
set protocols static route6 '3fff:10::/64' next-hop '3fff:20::201'
set protocols static route6 '3fff:1::/64' next-hop '3fff:10::100' bfd multihop
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 3: Set the following configuration in DUT2 :

set interfaces ethernet eth0 address '3fff:10::101/64'
set interfaces ethernet eth1 address '3fff:20::201/64'
set protocols static route6 '3fff:1::/64' next-hop '3fff:10::100'
set protocols static route6 '3fff:2::/64' next-hop '3fff:20::200'
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 4: Ping IP address 3fff:20::200 from DUT0:

admin@DUT0$ ping 3fff:20::200 count 1 size 56 timeout 1
Show output
PING 3fff:20::200(3fff:20::200) 56 data bytes
64 bytes from 3fff:20::200: icmp_seq=1 ttl=63 time=215 ms

--- 3fff:20::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 214.711/214.711/214.711/0.000 ms

Step 5: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=63 time=0.377 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.377/0.377/0.377/0.000 ms

Note

Check that the operational command ‘protocols bfd show static route’ works, and shows that they are each other’s peers and that their status is installed, indicating that the next-hop router is reachable

Step 6: Run command protocols bfd show static route at DUT0 and check if output matches the following regular expressions:

3fff:20::200
status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        3fff:2::/64 peer 3fff:20::200 (status: installed)

Step 7: Run command protocols bfd show static route at DUT1 and check if output matches the following regular expressions:

3fff:10::100
status: installed
Show output
Showing BFD monitored static routes:

  Next hops:
    VRF BFD IPv4 Unicast:

    VRF BFD IPv4 Multicast:

    VRF BFD IPv6 Unicast:
    VRF BGP IPv4 Unicast:

    VRF BGP IPv4 Multicast:

    VRF BGP IPv6 Unicast:
    VRF default IPv4 Unicast:

    VRF default IPv4 Multicast:

    VRF default IPv6 Unicast:
        3fff:1::/64 peer 3fff:10::100 (status: installed)

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established)

Step 8: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

3fff:20::200
Status: up
Show output
BFD Peers:
        peer 3fff:20::200 multihop local-address 3fff:10::100 vrf default
                ID: 230011893
                Remote ID: 27544869
                Active mode
                Minimum TTL: 2
                Status: up
                Uptime: 3 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 9: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

3fff:10::100
Status: up
Show output
BFD Peers:
        peer 3fff:10::100 multihop local-address 3fff:20::200 vrf default
                ID: 27544869
                Remote ID: 230011893
                Active mode
                Minimum TTL: 2
                Status: up
                Uptime: 3 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Test DUT0 Source IP IPv6

Description

Captures BFD packets and verifies the source address is correct when packets are sent from DUT0.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '::/0' next-hop '3fff:10::200' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' bfd source-ip '3fff:10::100'
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Capture packets and show one to verify that the source address is 3fff:10::100:

Note

Source line:

Show output
24 2026-03-05 16:09:41.407645798 3fff:10::100 → 3fff:10::200 BFD Control 86 Diag: No Diagnostic, State: Down, Flags: 0x00

Test DUT1 Source IP IPv6

Description

Captures BFD packets and verifies the source address is correct when packets are sent from DUT1.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols static route6 '::/0' next-hop '3fff:10::200' bfd source-ip '3fff:10::200'
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Capture packets and show one to verify that the source address is 3fff:10::200:

Note

Source line:

Show output
25 2026-03-05 16:09:54.413353818 3fff:10::200 → 3fff:10::100 BFD Control 86 Diag: No Diagnostic, State: Down, Flags: 0x00

Test Profile IPv6

Description

Checks that all BFD profile configured parameters are shown.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address '3fff:10::100/64'
set protocols bfd profile PFL detect-multiplier 5
set protocols bfd profile PFL echo-interval 60
set protocols bfd profile PFL passive-mode
set protocols bfd profile PFL receive-interval 400
set protocols bfd profile PFL transmit-interval 400
set protocols static route6 '::/0' next-hop '3fff:10::200' bfd profile PFL
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address '3fff:10::200/64'
set protocols static route6 '::/0' next-hop '3fff:10::100' bfd
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Note

Check connectivity

Step 3: Ping IP address 3fff:10::200 from DUT0:

admin@DUT0$ ping 3fff:10::200 count 1 size 56 timeout 1
Show output
PING 3fff:10::200(3fff:10::200) 56 data bytes
64 bytes from 3fff:10::200: icmp_seq=1 ttl=64 time=208 ms

--- 3fff:10::200 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 207.513/207.513/207.513/0.000 ms

Step 4: Ping IP address 3fff:10::100 from DUT1:

admin@DUT1$ ping 3fff:10::100 count 1 size 56 timeout 1
Show output
PING 3fff:10::100(3fff:10::100) 56 data bytes
64 bytes from 3fff:10::100: icmp_seq=1 ttl=64 time=0.513 ms

--- 3fff:10::100 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.513/0.513/0.513/0.000 ms

Note

Check that they are each other’s peers and that their status is up (the BFD session has beedn successfully established). Check that all configured profile parameters are shown in DUT0

Step 5: Run command protocols bfd show peers at DUT0 and check if output matches the following regular expressions:

3fff:10::200
Status: up
Detect-multiplier: 5
Echo receive interval: disabled
Echo transmission interval: disabled
Passive mode
Receive interval: 400ms
Transmission interval: 400ms
Show output
BFD Peers:
        peer 3fff:10::200 vrf default
                ID: 746962295
                Remote ID: 127643681
                Passive mode
                Status: up
                Uptime: 0 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: disabled
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms

Step 6: Run command protocols bfd show peers at DUT1 and check if output matches the following regular expressions:

3fff:10::100
Status: up
Show output
BFD Peers:
        peer 3fff:10::100 vrf default
                ID: 127643681
                Remote ID: 746962295
                Active mode
                Status: up
                Uptime: 1 second(s)
                Diagnostics: ok
                Remote diagnostics: ok
                Peer Type: dynamic
                RTT min/avg/max: 0/0/0 usec
                Local timers:
                        Detect-multiplier: 3
                        Receive interval: 300ms
                        Transmission interval: 300ms
                        Echo receive interval: 50ms
                        Echo transmission interval: disabled
                Remote timers:
                        Detect-multiplier: 5
                        Receive interval: 400ms
                        Transmission interval: 400ms
                        Echo receive interval: disabled