Radius Terminate Capture
These scenarios show different acct-terminate-causes that are sent by OSDx devices when 802.1x sessions end.
Test 802.1x User Request Cause
Description
This scenario shows how to stop an 802.1x session using
operational command supplicant disconnect.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=1.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.488 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.488/0.488/0.488/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator 802.1x max-retransmissions 2 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-802.1x set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX1/binAljYG3UYjN76Hn/5slWs3f3QgexyFQH0HZsV6GT+vDKipXTTAf+0q70hfSVohiZ8+AEC+hww== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.535 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.535/0.535/0.535/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set interfaces ethernet eth2 supplicant encrypted-password U2FsdGVkX1+J4Aer3xeYqAwy6rYkycdsDb2VITpcIDA= set interfaces ethernet eth2 supplicant username testing set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Run command interfaces ethernet eth2 supplicant show status at DUT1 and check if output contains the following tokens:
AuthorizedShow output
--------------------------------------------------- Field Value --------------------------------------------------- EAP State SUCCESS EAP TLS Cipher ECDHE-RSA-AES256-GCM-SHA384 EAP TLS Version TLSv1.2 PAE State AUTHENTICATED Supplicant Port Status Authorized WPA State COMPLETED
Step 7: Run command interfaces ethernet eth2 supplicant show stats at DUT1 and check if output matches the following regular expressions:
Port Status\s+AuthorizedShow output
------------------------------- Field Value ------------------------------- EAPoL Frames (Rx) 11 EAPoL Frames (Tx) 11 Invalid Frames (Rx) 0 Logoff Frames (Tx) 0 Port Status Authorized Req Frames (Rx) 9 Req ID Frames (Rx) 1 Resp Frames (Tx) 10 Start Frames (Tx) 1
Step 8: Run command interfaces ethernet eth2 authenticator show stats at DUT0 and check if output matches the following regular expressions:
Authentication Successes\s+1 Authentication Mode\s+802\.1XShow output
--------------------------------------------- Field Value --------------------------------------------- Access Challenges 9 Authentication Backend RADIUS Authentication Failures 0 Authentication Mode 802.1X Authentication Status Authorized (802.1X) Authentication Successes 1 EAPoL frames (Rx) 11 EAPoL frames (Tx) 11 Quiet Period 60 Reauthenticate FALSE Reauthenticate Period 0 Session Time 0 Session User MAC de:ad:be:ef:6c:12 Session User Name testing
Step 9: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.809 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.809/0.809/0.809/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Step 10: Run command interfaces ethernet eth2 supplicant disconnect at DUT1 and expect this output:
Show output
OK
Step 11: Run command interfaces ethernet eth2 authenticator show status at DUT0 and check if output contains the following tokens:
Current status: UnauthorizedShow output
Current status: Unauthorized
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:02:23.619381 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 195: (tos 0x0, ttl 63, id 63594, offset 0, flags [none], proto UDP (17), length 181) 10.215.168.66.53343 > 10.215.168.1.1813: [bad udp cksum 0x66a4 -> 0x0bb5!] RADIUS, length: 153 Accounting-Request (4), id: 0x0c, Authenticator: 5d016d990af3629877a273d082993705 Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: RADIUS 0x0000: 0000 0001 User-Name Attribute (1), length: 9, Value: testing 0x0000: 7465 7374 696e 67 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: F538C109EDC847D1 0x0000: 4635 3338 4331 3039 4544 4338 3437 4431 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:02:23 2026 0x0000: 6a21 a18f Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Terminate-Cause Attribute (49), length: 6, Value: User Request 0x0000: 0000 0001 1 packet captured
Test 802.1x Lost Carrier Cause
Description
This scenario shows how an 802.1x session is stopped
after a link down event in DUT0 eth2.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=2.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.627 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.627/0.627/0.627/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator 802.1x max-retransmissions 2 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator coa client 10.215.168.1 set interfaces ethernet eth2 authenticator coa encrypted-secret U2FsdGVkX1/fzddTaQBkV22H7wZUPeYldy98656dfBs= set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-802.1x set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX1+fQOLC4mIwfBagsJJf11EznEwJ7WrUqyXAsuFoTNzr5TPGIm3K6T1qnIY2nhCswJYekT0btqMXIw== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.800 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.800/0.800/0.800/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set interfaces ethernet eth2 supplicant encrypted-password U2FsdGVkX18MNhzARv+xiZrz5ycwTwRRc2+M5XN+izg= set interfaces ethernet eth2 supplicant username testing set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Run command interfaces ethernet eth2 supplicant show status at DUT1 and check if output contains the following tokens:
AuthorizedShow output
--------------------------------------------------- Field Value --------------------------------------------------- EAP State SUCCESS EAP TLS Cipher ECDHE-RSA-AES256-GCM-SHA384 EAP TLS Version TLSv1.2 PAE State AUTHENTICATED Supplicant Port Status Authorized WPA State COMPLETED
Step 7: Run command interfaces ethernet eth2 supplicant show stats at DUT1 and check if output matches the following regular expressions:
Port Status\s+AuthorizedShow output
------------------------------- Field Value ------------------------------- EAPoL Frames (Rx) 11 EAPoL Frames (Tx) 11 Invalid Frames (Rx) 0 Logoff Frames (Tx) 0 Port Status Authorized Req Frames (Rx) 9 Req ID Frames (Rx) 1 Resp Frames (Tx) 10 Start Frames (Tx) 1
Step 8: Run command interfaces ethernet eth2 authenticator show stats at DUT0 and check if output matches the following regular expressions:
Authentication Successes\s+1 Authentication Mode\s+802\.1XShow output
--------------------------------------------- Field Value --------------------------------------------- Access Challenges 9 Authentication Backend RADIUS Authentication Failures 0 Authentication Mode 802.1X Authentication Status Authorized (802.1X) Authentication Successes 1 EAPoL frames (Rx) 11 EAPoL frames (Tx) 11 Quiet Period 60 Reauthenticate FALSE Reauthenticate Period 0 Session Time 0 Session User MAC de:ad:be:ef:6c:12 Session User Name testing
Step 9: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.840 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.840/0.840/0.840/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Note
Remove the link between DUT0 and DUT1 to provoke a link-down event.
Step 10: Run command interfaces ethernet eth2 authenticator show status at DUT0 and expect this output:
Show output
Error: no supplicant found CLI Error: Command error
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:02:46.198872 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 195: (tos 0x0, ttl 63, id 5560, offset 0, flags [none], proto UDP (17), length 181) 10.215.168.66.43606 > 10.215.168.1.1813: [bad udp cksum 0x66a4 -> 0xf135!] RADIUS, length: 153 Accounting-Request (4), id: 0x0c, Authenticator: 92d36fbff4dabd3e77e9f5050bdce520 Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: RADIUS 0x0000: 0000 0001 User-Name Attribute (1), length: 9, Value: testing 0x0000: 7465 7374 696e 67 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: 5DA5836ADA9CB938 0x0000: 3544 4135 3833 3641 4441 3943 4239 3338 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:02:45 2026 0x0000: 6a21 a1a5 Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 10 secs 0x0000: 0000 000a Acct-Terminate-Cause Attribute (49), length: 6, Value: Lost Carrier 0x0000: 0000 0002 1 packet captured
Test MAB Lost Carrier Cause
Description
This scenario shows how a MAB-authenticated session is
stopped after a link-down event in DUT0 eth2.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=2.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.495 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.495/0.495/0.495/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator coa client 10.215.168.1 set interfaces ethernet eth2 authenticator coa encrypted-secret U2FsdGVkX19D8Ud6oH/9D8H46ipQp2rcBRURze1n4ms= set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-MAB set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX1+E5cuZcNG6KaoSmzynjAcP9S2NsivqRJwv9NBVU1rlTd4A6cQd06Iaps7qFm1Gra/KGLyE+eggiQ== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.481 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.481/0.481/0.481/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.396 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.396/0.396/0.396/0.000 ms
Step 7: Run command interfaces ethernet eth2 authenticator show stats at DUT0 and check if output matches the following regular expressions:
Authentication Successes\s+1 Authentication Mode\s+MABShow output
------------------------------------------- Field Value ------------------------------------------- Access Challenges 0 Authentication Backend RADIUS Authentication Failures 0 Authentication Mode MAB Authentication Status Authorized (MAB) Authentication Successes 1 EAPoL frames (Rx) 0 EAPoL frames (Tx) 0 Quiet Period 60 Reauthenticate FALSE Reauthenticate Period 0 Session Time 3 Session User MAC de:ad:be:ef:6c:12 Session User Name N/A
Step 8: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.271 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.271/0.271/0.271/0.000 ms
Step 9: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.249 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.249/0.249/0.249/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Note
Remove the link between DUT0 and DUT1 to provoke a link-down event.
Step 10: Run command interfaces ethernet eth2 authenticator show status at DUT0 and expect this output:
Show output
Error: no supplicant found CLI Error: Command error
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:03:10.633768 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 205: (tos 0x0, ttl 63, id 45615, offset 0, flags [none], proto UDP (17), length 191) 10.215.168.66.50722 > 10.215.168.1.1813: [bad udp cksum 0x66ae -> 0xbe3a!] RADIUS, length: 163 Accounting-Request (4), id: 0x02, Authenticator: 6381fdb90993485573f40a62cb160cd8 Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: Local 0x0000: 0000 0002 User-Name Attribute (1), length: 19, Value: de:ad:be:ef:6c:12 0x0000: 6465 3a61 643a 6265 3a65 663a 3663 3a31 0x0010: 32 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: 86DC616FD2D3DD97 0x0000: 3836 4443 3631 3646 4432 4433 4444 3937 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:03:10 2026 0x0000: 6a21 a1be Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 10 secs 0x0000: 0000 000a Acct-Terminate-Cause Attribute (49), length: 6, Value: Lost Carrier 0x0000: 0000 0002 1 packet captured
Test 802.1x Idle Timeout Cause
Description
This scenario shows how an 802.1x session is stopped
after a reauthentication timeout.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=4.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.578 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.578/0.578/0.578/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator 802.1x max-retransmissions 2 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-802.1x set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 30 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX19m9VOpvya/AKHejV9R/K2Bi72i3gqzyI12+hkjNWDri9odU13iqyhwPThsQgqV45NjoVVpS9bGBw== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=1.31 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.311/1.311/1.311/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set interfaces ethernet eth2 supplicant encrypted-password U2FsdGVkX1/XLnvpYUof1yb5qsDcX7jqIdyNagiXLTY= set interfaces ethernet eth2 supplicant username testing set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Run command interfaces ethernet eth2 supplicant show status at DUT1 and check if output contains the following tokens:
AuthorizedShow output
--------------------------------------------------- Field Value --------------------------------------------------- EAP State SUCCESS EAP TLS Cipher ECDHE-RSA-AES256-GCM-SHA384 EAP TLS Version TLSv1.2 PAE State AUTHENTICATED Supplicant Port Status Authorized WPA State COMPLETED
Step 7: Run command interfaces ethernet eth2 supplicant show stats at DUT1 and check if output matches the following regular expressions:
Port Status\s+AuthorizedShow output
------------------------------- Field Value ------------------------------- EAPoL Frames (Rx) 11 EAPoL Frames (Tx) 11 Invalid Frames (Rx) 0 Logoff Frames (Tx) 0 Port Status Authorized Req Frames (Rx) 9 Req ID Frames (Rx) 1 Resp Frames (Tx) 10 Start Frames (Tx) 1
Step 8: Run command interfaces ethernet eth2 authenticator show stats at DUT0 and check if output matches the following regular expressions:
Authentication Successes\s+1 Authentication Mode\s+802\.1XShow output
--------------------------------------------- Field Value --------------------------------------------- Access Challenges 9 Authentication Backend RADIUS Authentication Failures 0 Authentication Mode 802.1X Authentication Status Authorized (802.1X) Authentication Successes 1 EAPoL frames (Rx) 11 EAPoL frames (Tx) 11 Quiet Period 60 Reauthenticate TRUE Reauthenticate Period 30 Session Time 0 Session User MAC de:ad:be:ef:6c:12 Session User Name testing
Step 9: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.839 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.839/0.839/0.839/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Note
Disable DUT1 interface or remove address configuration to prevent the device from responding EAP requests.
Step 10: Modify the following configuration lines in DUT1 :
set interfaces ethernet eth2 disable
Step 11: Run command interfaces ethernet eth2 authenticator show status at DUT0 and check if output contains the following tokens:
Current status: UnauthorizedShow output
Current status: Unauthorized
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:04:15.166715 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 195: (tos 0x0, ttl 63, id 57746, offset 0, flags [none], proto UDP (17), length 181) 10.215.168.66.45673 > 10.215.168.1.1813: [bad udp cksum 0x66a4 -> 0xdee9!] RADIUS, length: 153 Accounting-Request (4), id: 0x0c, Authenticator: bbfff972dc721d51c865d8ad2f491a46 Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: RADIUS 0x0000: 0000 0001 User-Name Attribute (1), length: 9, Value: testing 0x0000: 7465 7374 696e 67 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: A39CD96C4121DC7C 0x0000: 4133 3943 4439 3643 3431 3231 4443 3743 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:04:14 2026 0x0000: 6a21 a1fe Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 51 secs 0x0000: 0000 0033 Acct-Terminate-Cause Attribute (49), length: 6, Value: Idle Timeout 0x0000: 0000 0004 1 packet captured
Test 802.1x Admin Reset Cause
Description
This scenario shows how to stop an 802.1x session using
operational command authenticator disassociate.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=6.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.763 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.763/0.763/0.763/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator 802.1x max-retransmissions 2 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-802.1x set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX196wChnlC7UWOqhxM/HYrHrPDaQ+joEUzkEc0ybVO7KaGX4b2gDsFt2ODOojMvJWa5PNutd3GSwKg== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.543 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.543/0.543/0.543/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set interfaces ethernet eth2 supplicant encrypted-password U2FsdGVkX1+015vFAXxd84Mpa20dN+IzW4AN7kZCLyM= set interfaces ethernet eth2 supplicant username testing set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Run command interfaces ethernet eth2 supplicant show status at DUT1 and check if output contains the following tokens:
AuthorizedShow output
--------------------------------------------------- Field Value --------------------------------------------------- EAP State SUCCESS EAP TLS Cipher ECDHE-RSA-AES256-GCM-SHA384 EAP TLS Version TLSv1.2 PAE State AUTHENTICATED Supplicant Port Status Authorized WPA State COMPLETED
Step 7: Run command interfaces ethernet eth2 supplicant show stats at DUT1 and check if output matches the following regular expressions:
Port Status\s+AuthorizedShow output
------------------------------- Field Value ------------------------------- EAPoL Frames (Rx) 11 EAPoL Frames (Tx) 11 Invalid Frames (Rx) 0 Logoff Frames (Tx) 0 Port Status Authorized Req Frames (Rx) 9 Req ID Frames (Rx) 1 Resp Frames (Tx) 10 Start Frames (Tx) 1
Step 8: Run command interfaces ethernet eth2 authenticator show stats at DUT0 and check if output matches the following regular expressions:
Authentication Successes\s+1 Authentication Mode\s+802\.1XShow output
--------------------------------------------- Field Value --------------------------------------------- Access Challenges 9 Authentication Backend RADIUS Authentication Failures 0 Authentication Mode 802.1X Authentication Status Authorized (802.1X) Authentication Successes 1 EAPoL frames (Rx) 11 EAPoL frames (Tx) 11 Quiet Period 60 Reauthenticate FALSE Reauthenticate Period 0 Session Time 0 Session User MAC de:ad:be:ef:6c:12 Session User Name testing
Step 9: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.928 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.928/0.928/0.928/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Step 10: Run command interfaces ethernet eth2 authenticator disassociate at DUT0 and expect this output:
Show output
OK
Step 11: Run command interfaces ethernet eth2 authenticator show status at DUT0 and check if output contains the following tokens:
Current status: UnauthorizedShow output
Current status: Unauthorized
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:04:28.704565 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 195: (tos 0x0, ttl 63, id 38073, offset 0, flags [none], proto UDP (17), length 181) 10.215.168.66.50499 > 10.215.168.1.1813: [bad udp cksum 0x66a4 -> 0x32ca!] RADIUS, length: 153 Accounting-Request (4), id: 0x0c, Authenticator: e595fc9119f3c7c8c9b0c62e98c44ec2 Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: RADIUS 0x0000: 0000 0001 User-Name Attribute (1), length: 9, Value: testing 0x0000: 7465 7374 696e 67 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: A3D22179A69DE1D5 0x0000: 4133 4432 3231 3739 4136 3944 4531 4435 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:04:27 2026 0x0000: 6a21 a20b Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Terminate-Cause Attribute (49), length: 6, Value: Admin Reset 0x0000: 0000 0006 1 packet captured
Test MAB Admin Reset Cause
Description
This scenario shows how to stop a MAB authenticated session
using operational command authenticator disassociate.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=6.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.482 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.482/0.482/0.482/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-MAB set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX1+flq/cV3WqrYFqM+my51zvXnpM9GP8Mzka+wnk0IMWkA1fwIuuFe55TWkry3o79IKbsMGqPGTi5A== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.562 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.562/0.562/0.562/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.691 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.691/0.691/0.691/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Step 7: Run command interfaces ethernet eth2 authenticator disassociate at DUT0 and expect this output:
Show output
OK
Step 8: Run command interfaces ethernet eth2 authenticator show status at DUT0 and check if output contains the following tokens:
Current status: UnauthorizedShow output
Current status: Unauthorized
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:04:43.474213 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 205: (tos 0x0, ttl 63, id 19244, offset 0, flags [none], proto UDP (17), length 191) 10.215.168.66.54837 > 10.215.168.1.1813: [bad udp cksum 0x66ae -> 0x65e4!] RADIUS, length: 163 Accounting-Request (4), id: 0x02, Authenticator: 928d4c843a4502af2a4cac2365f7b116 Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: Local 0x0000: 0000 0002 User-Name Attribute (1), length: 19, Value: de:ad:be:ef:6c:12 0x0000: 6465 3a61 643a 6265 3a65 663a 3663 3a31 0x0010: 32 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: D68D2FDE3CC74DB5 0x0000: 4436 3844 3246 4445 3343 4337 3444 4235 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:04:43 2026 0x0000: 6a21 a21b Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Terminate-Cause Attribute (49), length: 6, Value: Admin Reset 0x0000: 0000 0006 1 packet captured
Test 802.1x Admin Restart Cause
Description
This scenario shows how to restart an 802.1x session using
operational command authenticator restart.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=6.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.236 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.236/0.236/0.236/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator 802.1x max-retransmissions 2 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-802.1x set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX1/gE+mtKBLZ7CYdJPYaTcobdkmycvfHW6eW7+omRM+7ytSDC/M0I/LVwUyIvs0hJOEJkgfNUflZfQ== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.600 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.600/0.600/0.600/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set interfaces ethernet eth2 supplicant encrypted-password U2FsdGVkX1+OorWBwSupx4ZfZcPH+YAc7d9mPGAE25Y= set interfaces ethernet eth2 supplicant username testing set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Run command interfaces ethernet eth2 supplicant show status at DUT1 and check if output contains the following tokens:
AuthorizedShow output
--------------------------------------------------- Field Value --------------------------------------------------- EAP State SUCCESS EAP TLS Cipher ECDHE-RSA-AES256-GCM-SHA384 EAP TLS Version TLSv1.2 PAE State AUTHENTICATED Supplicant Port Status Authorized WPA State COMPLETED
Step 7: Run command interfaces ethernet eth2 supplicant show stats at DUT1 and check if output matches the following regular expressions:
Port Status\s+AuthorizedShow output
------------------------------- Field Value ------------------------------- EAPoL Frames (Rx) 11 EAPoL Frames (Tx) 11 Invalid Frames (Rx) 0 Logoff Frames (Tx) 0 Port Status Authorized Req Frames (Rx) 9 Req ID Frames (Rx) 1 Resp Frames (Tx) 10 Start Frames (Tx) 1
Step 8: Run command interfaces ethernet eth2 authenticator show stats at DUT0 and check if output matches the following regular expressions:
Authentication Successes\s+1 Authentication Mode\s+802\.1XShow output
--------------------------------------------- Field Value --------------------------------------------- Access Challenges 9 Authentication Backend RADIUS Authentication Failures 0 Authentication Mode 802.1X Authentication Status Authorized (802.1X) Authentication Successes 1 EAPoL frames (Rx) 11 EAPoL frames (Tx) 11 Quiet Period 60 Reauthenticate FALSE Reauthenticate Period 0 Session Time 0 Session User MAC de:ad:be:ef:6c:12 Session User Name testing
Step 9: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.673 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.673/0.673/0.673/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Step 10: Run command interfaces ethernet eth2 authenticator restart at DUT0 and expect this output:
Step 11: Run command interfaces ethernet eth2 authenticator show status at DUT0 and expect this output:
Show output
Error: no supplicant found CLI Error: Command error
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:04:55.720073 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 195: (tos 0x0, ttl 63, id 63329, offset 0, flags [none], proto UDP (17), length 181) 10.215.168.66.57198 > 10.215.168.1.1813: [bad udp cksum 0x66a4 -> 0x914c!] RADIUS, length: 153 Accounting-Request (4), id: 0x0c, Authenticator: 66c139767ae7303cb5e9bf23d1fb5224 Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: RADIUS 0x0000: 0000 0001 User-Name Attribute (1), length: 9, Value: testing 0x0000: 7465 7374 696e 67 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: 131060346A6CE57C 0x0000: 3133 3130 3630 3334 3641 3643 4535 3743 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:04:55 2026 0x0000: 6a21 a227 Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Terminate-Cause Attribute (49), length: 6, Value: Admin Reset 0x0000: 0000 0006 1 packet captured
Test MAB Admin Restart Cause
Description
This scenario shows how to restart a MAB authenticated session
using operational command authenticator restart.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=6.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.538 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.538/0.538/0.538/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-MAB set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX1/GsA6Kt3mlApYgGYHOHwhQYOuzB6QBlyQMKzv9zaJYMveLvY0H1JG2ubbW8CEL3UDRzfu2jUyrlQ== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.477 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.477/0.477/0.477/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.266 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.266/0.266/0.266/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Step 7: Run command interfaces ethernet eth2 authenticator restart at DUT0 and expect this output:
Step 8: Run command interfaces ethernet eth2 authenticator show status at DUT0 and expect this output:
Show output
Error: no supplicant found CLI Error: Command error
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:05:10.918857 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 205: (tos 0x0, ttl 63, id 54222, offset 0, flags [none], proto UDP (17), length 191) 10.215.168.66.35006 > 10.215.168.1.1813: [bad udp cksum 0x66ae -> 0x95b6!] RADIUS, length: 163 Accounting-Request (4), id: 0x02, Authenticator: 9da75cb8cdb66a970d6a21dcd65ada1a Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: Local 0x0000: 0000 0002 User-Name Attribute (1), length: 19, Value: de:ad:be:ef:6c:12 0x0000: 6465 3a61 643a 6265 3a65 663a 3663 3a31 0x0010: 32 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: E8B49AB812869129 0x0000: 4538 4234 3941 4238 3132 3836 3931 3239 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:05:11 2026 0x0000: 6a21 a237 Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 01 secs 0x0000: 0000 0001 Acct-Terminate-Cause Attribute (49), length: 6, Value: Admin Reset 0x0000: 0000 0006 1 packet captured
Test 802.1x NAS Request Cause
Description
This scenario shows how to stop an 802.1x session from
the authentication server using a CoA message.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=10.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.547 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.547/0.547/0.547/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator 802.1x max-retransmissions 2 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator coa client 10.215.168.1 set interfaces ethernet eth2 authenticator coa encrypted-secret U2FsdGVkX1/m3b1ids1W9gxWJ4a8i7flkMk/EITUKNk= set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-802.1x set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX1/QVe/iq9l7P7csc5UVIPM2NjLaQrDEiiLTGcIaRYvpGDrldxROKqcvRTKAQ9ObQ3LdflOZw/pBUg== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.366 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.366/0.366/0.366/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set interfaces ethernet eth2 supplicant encrypted-password U2FsdGVkX19G0ksA2ugN0bFPQ1L6QC7cdO9Yrwh91Ko= set interfaces ethernet eth2 supplicant username testing set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Run command interfaces ethernet eth2 supplicant show status at DUT1 and check if output contains the following tokens:
AuthorizedShow output
--------------------------------------------------- Field Value --------------------------------------------------- EAP State SUCCESS EAP TLS Cipher ECDHE-RSA-AES256-GCM-SHA384 EAP TLS Version TLSv1.2 PAE State AUTHENTICATED Supplicant Port Status Authorized WPA State COMPLETED
Step 7: Run command interfaces ethernet eth2 supplicant show stats at DUT1 and check if output matches the following regular expressions:
Port Status\s+AuthorizedShow output
------------------------------- Field Value ------------------------------- EAPoL Frames (Rx) 11 EAPoL Frames (Tx) 11 Invalid Frames (Rx) 0 Logoff Frames (Tx) 0 Port Status Authorized Req Frames (Rx) 9 Req ID Frames (Rx) 1 Resp Frames (Tx) 10 Start Frames (Tx) 1
Step 8: Run command interfaces ethernet eth2 authenticator show stats at DUT0 and check if output matches the following regular expressions:
Authentication Successes\s+1 Authentication Mode\s+802\.1XShow output
--------------------------------------------- Field Value --------------------------------------------- Access Challenges 9 Authentication Backend RADIUS Authentication Failures 0 Authentication Mode 802.1X Authentication Status Authorized (802.1X) Authentication Successes 1 EAPoL frames (Rx) 11 EAPoL frames (Tx) 11 Quiet Period 60 Reauthenticate FALSE Reauthenticate Period 0 Session Time 0 Session User MAC de:ad:be:ef:6c:12 Session User Name testing
Step 9: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.511 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.511/0.511/0.511/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Note
Send a CoA/Disconnect request from the RADIUS server
On Linux, the FreeRADIUS package includes the
radtest utility, which can be used to send these messages:
Show output
$ cat /osdx-tests/utils/dot1x/auth_dot1x.req User-Name = "testing" $ radclient -s -t 1 -r 1 10.215.168.66:3799 disconnect coa_secret -f /osdx-tests/utils/dot1x/auth_dot1x.req Sent Disconnect-Request Id 126 from 0.0.0.0:52528 to 10.215.168.66:3799 length 29 Received Disconnect-ACK Id 126 from 10.215.168.66:3799 to 10.215.168.1:52528 length 44 Packet summary: Accepted : 1 Rejected : 0 Lost : 0 Passed filter : 1 Failed filter : 0
Step 10: Run command interfaces ethernet eth2 authenticator show status at DUT0 and check if output contains the following tokens:
Current status: UnauthorizedShow output
Current status: Unauthorized
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:05:23.851086 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 195: (tos 0x0, ttl 63, id 51673, offset 0, flags [none], proto UDP (17), length 181) 10.215.168.66.32856 > 10.215.168.1.1813: [bad udp cksum 0x66a4 -> 0xf63c!] RADIUS, length: 153 Accounting-Request (4), id: 0x0c, Authenticator: f2834c1c1efbcfed7efd70a073333b2d Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: RADIUS 0x0000: 0000 0001 User-Name Attribute (1), length: 9, Value: testing 0x0000: 7465 7374 696e 67 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: 5D2410240F4ACB4E 0x0000: 3544 3234 3130 3234 3046 3441 4342 3445 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:05:24 2026 0x0000: 6a21 a244 Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Terminate-Cause Attribute (49), length: 6, Value: NAS Request 0x0000: 0000 000a 1 packet captured
Test MAB NAS Request Cause
Description
This scenario shows how to stop a MAB-authenticated session
from the authentication server using a CoA message.
Accounting RADIUS stop messages should contain the
following attribute: acct-terminate-cause=10.
Scenario
Step 1: Set the following configuration in DUT2 :
set interfaces ethernet eth0 address 10.215.168.66/24 set interfaces ethernet eth0 traffic nat destination rule 1 address 192.168.200.2 set interfaces ethernet eth0 traffic nat source rule 1 address masquerade set interfaces ethernet eth1 address 192.168.200.1/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Ping IP address 10.215.168.1 from DUT2:
admin@DUT2$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=64 time=0.250 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.250/0.250/0.250/0.000 ms
Step 3: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.200.2/24 set interfaces ethernet eth2 address 192.168.100.1/24 set interfaces ethernet eth2 authenticator aaa accounting list1 set interfaces ethernet eth2 authenticator aaa authentication list1 set interfaces ethernet eth2 authenticator coa client 10.215.168.1 set interfaces ethernet eth2 authenticator coa encrypted-secret U2FsdGVkX1/Of9A40ifiRv3KNQ+GKCGHzCTITQXGwQI= set interfaces ethernet eth2 authenticator log-level debug set interfaces ethernet eth2 authenticator mode only-MAB set interfaces ethernet eth2 authenticator quiet-period 60 set interfaces ethernet eth2 authenticator reauth-period 0 set protocols static route 0.0.0.0/0 next-hop 192.168.200.1 set system aaa group radius radgroup1 server serv1 set system aaa list list1 method 1 group radius radgroup1 set system aaa server radius serv1 address 10.215.168.1 set system aaa server radius serv1 encrypted-key U2FsdGVkX1/5I9LJc0DZ6YZ+jrec6+cZhoT98TrsI78j49MSiUt+C/DECMie5ATJSURq20N9DKnaRmQZwlAGtw== set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 4: Ping IP address 10.215.168.1 from DUT0:
admin@DUT0$ ping 10.215.168.1 count 1 size 56 timeout 1Show output
PING 10.215.168.1 (10.215.168.1) 56(84) bytes of data. 64 bytes from 10.215.168.1: icmp_seq=1 ttl=63 time=0.578 ms --- 10.215.168.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.578/0.578/0.578/0.000 ms
Step 5: Set the following configuration in DUT1 :
set interfaces ethernet eth2 address 192.168.100.2/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 6: Ping IP address 192.168.100.1 from DUT1:
admin@DUT1$ ping 192.168.100.1 count 1 size 56 timeout 1Show output
PING 192.168.100.1 (192.168.100.1) 56(84) bytes of data. 64 bytes from 192.168.100.1: icmp_seq=1 ttl=64 time=0.303 ms --- 192.168.100.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.303/0.303/0.303/0.000 ms
Note
Start packet capture in DUT2 to filter RADIUS stop messages (e.g., traffic dump monitor interface eth0 detail filter "udp port 1813" packets 1).
Note
Send a CoA/Disconnect request from the RADIUS server
On Linux, the FreeRADIUS package includes the
radtest utility, which can be used to send these messages:
Show output
$ cat /osdx-tests/utils/dot1x/auth_mab.req User-Name = "de:ad:be:ef:6c:12" $ radclient -s -t 1 -r 1 10.215.168.66:3799 disconnect coa_secret -f /osdx-tests/utils/dot1x/auth_mab.req Sent Disconnect-Request Id 183 from 0.0.0.0:42613 to 10.215.168.66:3799 length 39 Received Disconnect-ACK Id 183 from 10.215.168.66:3799 to 10.215.168.1:42613 length 44 Packet summary: Accepted : 1 Rejected : 0 Lost : 0 Passed filter : 1 Failed filter : 0
Step 7: Run command interfaces ethernet eth2 authenticator show status at DUT0 and check if output contains the following tokens:
Current status: UnauthorizedShow output
Current status: Unauthorized
Note
Stop packet capture in DUT0 and expect
the following RADIUS messages:
Show output
eth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes 16:05:38.978087 de:ad:be:ef:6c:20 > fe:22:0e:3f:29:f8, ethertype IPv4 (0x0800), length 205: (tos 0x0, ttl 63, id 40378, offset 0, flags [none], proto UDP (17), length 191) 10.215.168.66.58726 > 10.215.168.1.1813: [bad udp cksum 0x66ae -> 0xb3d5!] RADIUS, length: 163 Accounting-Request (4), id: 0x02, Authenticator: 6c493f96939ab3cc7119e9eb4cc7aa74 Acct-Status-Type Attribute (40), length: 6, Value: Stop 0x0000: 0000 0002 Acct-Authentic Attribute (45), length: 6, Value: Local 0x0000: 0000 0002 User-Name Attribute (1), length: 19, Value: de:ad:be:ef:6c:12 0x0000: 6465 3a61 643a 6265 3a65 663a 3663 3a31 0x0010: 32 Called-Station-Id Attribute (30), length: 20, Value: DE-AD-BE-EF-6C-02: 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d30 0x0010: 323a Service-Type Attribute (6), length: 6, Value: Framed 0x0000: 0000 0002 Calling-Station-Id Attribute (31), length: 19, Value: DE-AD-BE-EF-6C-12 0x0000: 4445 2d41 442d 4245 2d45 462d 3643 2d31 0x0010: 32 Acct-Session-Id Attribute (44), length: 18, Value: F5C953F7DBD0FA6F 0x0000: 4635 4339 3533 4637 4442 4430 4641 3646 NAS-Port-Type Attribute (61), length: 6, Value: Ethernet 0x0000: 0000 000f Connect-Info Attribute (77), length: 13, Value: Unsupported 0x0000: 556e 7375 7070 6f72 7465 64 NAS-Port-Id Attribute (87), length: 6, Value: eth2 0x0000: 6574 6832 Event-Timestamp Attribute (55), length: 6, Value: Thu Jun 4 16:05:39 2026 0x0000: 6a21 a253 Acct-Delay-Time Attribute (41), length: 6, Value: 00 secs 0x0000: 0000 0000 Acct-Session-Time Attribute (46), length: 6, Value: 01 secs 0x0000: 0000 0001 Acct-Terminate-Cause Attribute (49), length: 6, Value: NAS Request 0x0000: 0000 000a 1 packet captured