tunnel
- interfaces tunnel <id>
- SDE
M10-Smart
M2
RS420
AresC640
Tunnel interface
- Values:
tunN – Tunnel interface name
- Instances:
Multiple
- Required:
- interfaces tunnel <id> 6rd-prefix <ipv6net>
- SDE
M10-Smart
M2
RS420
AresC640
6rd network prefix
- Values:
ipv6net – IPv6 address and prefix length
- Instances:
Multiple
- interfaces tunnel <id> 6rd-relay-prefix <ipv4net>
- SDE
M10-Smart
M2
RS420
AresC640
6rd relay prefix
- Values:
ipv4net – IPv4 prefix of interface for 6rd
- Instances:
Multiple
- interfaces tunnel <id> address <ipv4cidr|ipv6cidr|id>
- SDE
M10-Smart
M2
RS420
AresC640
IP address
- Values:
ipv6cidr – IPv6 address and prefix length
dhcpv6 – Dynamic Host Configuration Protocol for IPv6
ipv4cidr – IPv4 address and prefix length
dhcp – Dynamic Host Configuration Protocol
- Instances:
Multiple
- interfaces tunnel <id> alarm
- SDE
M10-Smart
M2
RS420
AresC640
Enable or disable alarm according the link state
- interfaces tunnel <id> alarm down <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Alarm to be enabled if the link is down
- Reference:
- interfaces tunnel <id> bridge-group
- SDE
M10-Smart
M2
RS420
AresC640
Add this interface to a bridge group
- Required:
- interfaces tunnel <id> bridge-group bridge <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Bridge group name (br[0-9]+)
- Reference:
- interfaces tunnel <id> bridge-group isolate
- SDE
M10-Smart
M2
RS420
AresC640
Isolate port
- interfaces tunnel <id> bridge-group stp
- SDE
M10-Smart
M2
RS420
AresC640
Bridge port Spanning Tree Protocol configuration
- interfaces tunnel <id> bridge-group stp admin-edge
- SDE
M10-Smart
M2
RS420
AresC640
Enable the admin edge state
- interfaces tunnel <id> bridge-group stp bpdu-filter
- SDE
M10-Smart
M2
RS420
AresC640
Enable the BPDU filter capability
If enabled, this port will discard any ingress BPDUs and will not issue any BPUs
- interfaces tunnel <id> bridge-group stp bpdu-guard
- SDE
M10-Smart
M2
RS420
AresC640
Enable the bpduguard configuration
- interfaces tunnel <id> bridge-group stp cost <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Bridge port cost
- Values:
u32 – Auto (0)
u32 – Bridge port cost (1-65535)
- interfaces tunnel <id> bridge-group stp disable-auto-edge
- SDE
M10-Smart
M2
RS420
AresC640
Enable the auto transition to/from edge state
- interfaces tunnel <id> bridge-group stp network-assurance
- SDE
M10-Smart
M2
RS420
AresC640
Enable the bridge assurance capability
- interfaces tunnel <id> bridge-group stp p2p <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Enable Point-2-Point (P2P) detection mode
- interfaces tunnel <id> bridge-group stp priority <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Bridge port priority
- Values:
u32 – Bridge port priority (0-15)
- interfaces tunnel <id> bridge-group vlan <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Enable VLAN in this bridge port
- Values:
u32 – VLAN ID (1-4094)
- Instances:
Multiple
- interfaces tunnel <id> bridge-group vlan <u32> pvid
- SDE
M10-Smart
M2
RS420
AresC640
This VLAN specified is to be considered a PVID at ingress
Any untagged frames will be assigned to this VLAN
- interfaces tunnel <id> bridge-group vlan <u32> untagged
- SDE
M10-Smart
M2
RS420
AresC640
This VLAN is to be treated as untagged on egress
The bridge will always remove the VLAN tag from egress packets
- interfaces tunnel <id> description <id>
- SDE
M10-Smart
M2
RS420
AresC640
Description
- Values:
id – “Interface description is too long (limit 256 characters)” (1-256)
- interfaces tunnel <id> dhcp
- SDE
M10-Smart
M2
RS420
AresC640
Dynamic Host Configuration Protocol configuration
- interfaces tunnel <id> dhcp client
- SDE
M10-Smart
M2
RS420
AresC640
DHCP client configuration
- interfaces tunnel <id> dhcp client fallback <ipv4cidr|ipv6cidr>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
ipv4cidr – Fallback IP address
ipv6cidr – Fallback IP address
- interfaces tunnel <id> dhcp client rfc3442-routes
- SDE
M10-Smart
M2
RS420
AresC640
Install RFC3442 routes received from DHCP server
- interfaces tunnel <id> dhcp client send
- SDE
M10-Smart
M2
RS420
AresC640
Send user-defined options to the DHCP server
- interfaces tunnel <id> dhcp client send dhcp-client-identifier
- SDE
M10-Smart
M2
RS420
AresC640
Include the ‘dhcp-client-identifier’ option
- Instances:
Unique
- interfaces tunnel <id> dhcp client send dhcp-client-identifier base-mac
- SDE
M10-Smart
M2
RS420
AresC640
Use device base mac as identifier
- interfaces tunnel <id> dhcp client send dhcp-client-identifier serial-number
- SDE
M10-Smart
M2
RS420
AresC640
Use device serial number as identifier
- interfaces tunnel <id> dhcp client send dhcp-client-identifier string <id>
- SDE
M10-Smart
M2
RS420
AresC640
Use a string as identifier
- Values:
id – Identifier string (1-255)
- interfaces tunnel <id> dhcp client send vendor-class-identifier
- SDE
M10-Smart
M2
RS420
AresC640
Include the ‘vendor-class-identifier’ option
- Instances:
Unique
- interfaces tunnel <id> dhcp client send vendor-class-identifier string <id>
- SDE
M10-Smart
M2
RS420
AresC640
Use a string as identifier
- Values:
id – Identifier string (1-255)
- interfaces tunnel <id> dhcp-interface <ifc>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
ifc – DHCP interface that supplies the local IP address for this tunnel
- interfaces tunnel <id> dhcpv6
- SDE
M10-Smart
M2
RS420
AresC640
Dynamic Host Configuration Protocol v6 configuration
- interfaces tunnel <id> dhcpv6 client
- SDE
M10-Smart
M2
RS420
AresC640
DHCPv6 client configuration
- interfaces tunnel <id> dhcpv6 client parameters-only
- SDE
M10-Smart
M2
RS420
AresC640
Acquire only config parameters, not address
- interfaces tunnel <id> dhcpv6 client send
- SDE
M10-Smart
M2
RS420
AresC640
Send user-defined options to the DHCPv6 server
- interfaces tunnel <id> dhcpv6 client send duid <id>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
id – DHCPv6 DUID to be sent by dhcpv6 client
- interfaces tunnel <id> dhcpv6 client temporary
- SDE
M10-Smart
M2
RS420
AresC640
IPv6 “temporary” address
- interfaces tunnel <id> disable
- SDE
M10-Smart
M2
RS420
AresC640
Disable interface
- interfaces tunnel <id> disable advisor <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Advisor to enable or disable the interface
- Reference:
- interfaces tunnel <id> disable-offload
- SDE
M10-Smart
M2
RS420
AresC640
Disable offload engine in this interface
- interfaces tunnel <id> encapsulation <id>
- SDE
M10-Smart
M2
RS420
AresC640
Encapsulation of this tunnel interface [REQUIRED]
- Values:
gre – Generic Routing Encapsulation
gre-bridge – Generic Routing Encapsulation bridge interface
ipip – IP in IP encapsulation
sit – Simple Internet Transition encapsulation
ipip6 – IP in IP6 encapsulation
ip6ip6 – IP6 in IP6 encapsulation
- interfaces tunnel <id> flow
- SDE
M10-Smart
M2
RS420
AresC640
Active netflow on interface
- interfaces tunnel <id> flow egress
- SDE
M10-Smart
M2
RS420
AresC640
Active output traffic
- interfaces tunnel <id> flow egress selector <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Traffic selector
- Reference:
- interfaces tunnel <id> flow ingress
- SDE
M10-Smart
M2
RS420
AresC640
Active input traffic
- interfaces tunnel <id> flow ingress selector <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Traffic selector
- Reference:
- interfaces tunnel <id> ip
- SDE
M10-Smart
M2
RS420
AresC640
IPv4 routing parameters
- interfaces tunnel <id> ip igmp
- SDE
M10-Smart
M2
RS420
AresC640
Internet Group Management Protocol (IGMP) parameters
- interfaces tunnel <id> ip igmp join <ipv4>
- SDE
M10-Smart
M2
RS420
AresC640
Join multicast group
- Values:
ipv4 – Join multicast group on this interface
- interfaces tunnel <id> ip igmp last-member-query-count <u32>
- SDE
M10-Smart
M2
RS420
AresC640
IGMP last member query count
- Values:
u32 – IGMP last member query count (1-255)
- interfaces tunnel <id> ip igmp last-member-query-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
IGMP last member query interval
- Values:
u32 – IGMP last member query interval in deciseconds (1-65535)
- interfaces tunnel <id> ip igmp query-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
IGMP query interval
- Values:
u32 – IGMP query interval in seconds (1-65535)
- interfaces tunnel <id> ip igmp query-max-response-time <u32>
- SDE
M10-Smart
M2
RS420
AresC640
IGMP query response timeout value
- Values:
u32 – IGMP query response timeout value in deciseconds (1-65535)
- interfaces tunnel <id> ip igmp version <u32>
- SDE
M10-Smart
M2
RS420
AresC640
IGMP version
- Values:
u32 – IGMP version used on this interface (2-3)
- interfaces tunnel <id> ip multicast
- SDE
M10-Smart
M2
RS420
AresC640
Multicast parameters
- interfaces tunnel <id> ip multicast boundary-list <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Prefix-list to control for which groups to accept or ignore received PIM join or IGMP report messages
- Reference:
- interfaces tunnel <id> ip ospf
- SDE
M10-Smart
M2
RS420
AresC640
Open Shortest Path First (OSPF) parameters
- interfaces tunnel <id> ip ospf authentication
- SDE
M10-Smart
M2
RS420
AresC640
OSPF interface authentication
- interfaces tunnel <id> ip ospf authentication encrypted-password <password>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
password – Encrypted password
- interfaces tunnel <id> ip ospf authentication message-digest <id>
- SDE
M10-Smart
M2
RS420
AresC640
MD5 authentication parameters
- Values:
id – MD5 ID number (1-255)
- Instances:
Multiple
- interfaces tunnel <id> ip ospf authentication message-digest <id> encrypted-password <password>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
password – MD5 encrypted key
- interfaces tunnel <id> ip ospf authentication message-digest <id> password <txt>
- SDE
M10-Smart
M2
RS420
AresC640
MD5 key
- Values:
txt – MD5 Key (1-16)
- interfaces tunnel <id> ip ospf authentication password <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Plain text password
- interfaces tunnel <id> ip ospf bandwidth <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Bandwidth of interface (kilobits/sec)
- Values:
u32 – Bandwidth in kilobits/sec (for calculating OSPF cost) (1-10000000)
- interfaces tunnel <id> ip ospf cost <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interface cost
- Values:
u32 – OSPF interface cost (1-65535)
- interfaces tunnel <id> ip ospf dead-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interval after which neighbor is dead
- Values:
u32 – OSPF dead interval in seconds (1-65535)
- interfaces tunnel <id> ip ospf hello-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interval between hello packets
- Values:
u32 – Interval between OSPF hello packets in seconds (1-65535)
- interfaces tunnel <id> ip ospf mtu-ignore
- SDE
M10-Smart
M2
RS420
AresC640
Disable Maximum Transmission Unit (MTU) mismatch detection
- interfaces tunnel <id> ip ospf network <id>
- SDE
M10-Smart
M2
RS420
AresC640
Network type
- Values:
broadcast – Broadcast network type
non-broadcast – Non-broadcast network type
point-to-multipoint – Point-to-multipoint network type
point-to-point – Point-to-point network type
- interfaces tunnel <id> ip ospf priority <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Router priority
- Values:
u32 – Priority (0-255)
- interfaces tunnel <id> ip ospf retransmit-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interval between retransmitting lost link state advertisements
- Values:
u32 – Retransmit interval in seconds (3-65535)
- interfaces tunnel <id> ip ospf transmit-delay <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Link state transmit delay
- Values:
u32 – Transmit delay in seconds (1-65535)
- interfaces tunnel <id> ip pim
- SDE
M10-Smart
M2
RS420
AresC640
Protocol Independent Multicast (PIM) parameters
- interfaces tunnel <id> ip pim disable-bsm
- SDE
M10-Smart
M2
RS420
AresC640
Disable sending and receiving bootstrap messages
- interfaces tunnel <id> ip pim disable-unicast-bsm
- SDE
M10-Smart
M2
RS420
AresC640
Disable sending and receiving unicast bootstrap messages
- interfaces tunnel <id> ip pim drpriority <u32>
- SDE
M10-Smart
M2
RS420
AresC640
PIM Designated Router (DR) priority
- Values:
u32 – PIM DR priority for the interface (1-4294967295)
- interfaces tunnel <id> ip pim hello <u32>
- SDE
M10-Smart
M2
RS420
AresC640
PIM hello interval
- Values:
u32 – PIM hello interval in seconds (1-255)
- interfaces tunnel <id> ip pim passive
- SDE
M10-Smart
M2
RS420
AresC640
Disable sending and receiving all PIM control messages (such as: ASSERT, BSM, HELLO, JOIN, PRUNE, REGISTER, REGISTER-STOP)
- interfaces tunnel <id> ip reverse-path-filter <id>
- SDE
M10-Smart
M2
RS420
AresC640
Policy for source validation by reversed path, as specified in RFC3704
- Values:
strict – Enable Strict Reverse Path Forwarding as defined in RFC3704
loose – Enable Loose Reverse Path Forwarding as defined in RFC3704
disable – No source validation
- interfaces tunnel <id> ip rip
- SDE
M10-Smart
M2
RS420
AresC640
Routing Information Protocol (RIP) parameters
- interfaces tunnel <id> ip rip authentication
- SDE
M10-Smart
M2
RS420
AresC640
Authentication method
- interfaces tunnel <id> ip rip authentication encrypted-password <password>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
password – Encrypted password
- interfaces tunnel <id> ip rip authentication message-digest <u32>
- SDE
M10-Smart
M2
RS420
AresC640
MD5 authentication parameters
- Values:
u32 – MD5 ID number (1-255)
- Instances:
Multiple
- interfaces tunnel <id> ip rip authentication message-digest <u32> encrypted-password <password>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
password – MD5 encrypted key
- interfaces tunnel <id> ip rip authentication message-digest <u32> password <txt>
- SDE
M10-Smart
M2
RS420
AresC640
MD5 key
- Values:
txt – MD5 Key (1-16)
- interfaces tunnel <id> ip rip authentication password <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Plain text password
- Values:
txt – Plain text password (1-16)
- interfaces tunnel <id> ip rip split-horizon
- SDE
M10-Smart
M2
RS420
AresC640
Split horizon parameters
- interfaces tunnel <id> ip rip split-horizon disable
- SDE
M10-Smart
M2
RS420
AresC640
Disable split horizon on specified interface
- interfaces tunnel <id> ip rip split-horizon poison-reverse
- SDE
M10-Smart
M2
RS420
AresC640
Enable poison reverse for split-horizon
- interfaces tunnel <id> ipv6
- SDE
M10-Smart
M2
RS420
AresC640
IPv6 routing parameters
- interfaces tunnel <id> ipv6 address
- SDE
M10-Smart
M2
RS420
AresC640
IPv6 address auto-configuration modes
- interfaces tunnel <id> ipv6 address autoconf
- SDE
M10-Smart
M2
RS420
AresC640
Enable acquisition of IPv6 address using stateless autoconfig
- interfaces tunnel <id> ipv6 address eui64 <ipv6net>
- SDE
M10-Smart
M2
RS420
AresC640
Assign IPv6 address using EUI-64 based on MAC address
- Values:
ipv6net – 64-bit IPv6 prefix to use with EUI-64 to make address
- Instances:
Multiple
- interfaces tunnel <id> ipv6 address prefix-from-provider <id>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
id – IPv6 from Learned Prefix
- Instances:
Multiple
- interfaces tunnel <id> ipv6 address prefix-from-provider <id> ifc-ID <ipv6net>
- SDE
M10-Smart
M2
RS420
AresC640
Assign IPv6 address using Learned Prefixes
- Values:
< – 64-bit IPv6 prefix (:h:h:h:h/64>)
- Instances:
Multiple
- interfaces tunnel <id> ipv6 dhcp-client-pd <id>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
id – Name of learned prefix from provider
- interfaces tunnel <id> ipv6 disable-forwarding
- SDE
M10-Smart
M2
RS420
AresC640
Disable IPv6 forwarding on this interface only
- interfaces tunnel <id> ipv6 dup-addr-detect-transmits <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Number of NS messages to send while performing DAD
- Values:
u32 – Number of NS messages to send while performing DAD (0-2147483647)
- interfaces tunnel <id> ipv6 ospfv3
- SDE
M10-Smart
M2
RS420
AresC640
IPv6 Open Shortest Path First (OSPFv3) parameters
- interfaces tunnel <id> ipv6 ospfv3 area <u32|ipv4>
- SDE
M10-Smart
M2
RS420
AresC640
OSPFv3 Area
- Values:
u32 – OSPFv3 area in decimal notation (0-4294967295)
ipv4 – OSPFv3 area in dotted decimal notation
- interfaces tunnel <id> ipv6 ospfv3 authentication
- SDE
M10-Smart
M2
RS420
AresC640
OSPFv3 interface authentication
- Instances:
Unique
- interfaces tunnel <id> ipv6 ospfv3 authentication hmac-sha-256 <u32>
- SDE
M10-Smart
M2
RS420
AresC640
HMAC-SHA-256 authentication parameters
- Values:
u32 – HMAC-SHA-256 key ID (1-65535)
- Instances:
Multiple
- interfaces tunnel <id> ipv6 ospfv3 authentication hmac-sha-256 <u32> encrypted-password <password>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
password – HMAC-SHA-256 encrypted password
- interfaces tunnel <id> ipv6 ospfv3 authentication hmac-sha-256 <u32> password <txt>
- SDE
M10-Smart
M2
RS420
AresC640
HMAC-SHA-256 plain text password
- Values:
txt – HMAC-SHA-256 plain text password (1-16)
- interfaces tunnel <id> ipv6 ospfv3 authentication md5 <u32>
- SDE
M10-Smart
M2
RS420
AresC640
MD5 authentication parameters
- Values:
u32 – MD5 key ID (1-65535)
- Instances:
Multiple
- interfaces tunnel <id> ipv6 ospfv3 authentication md5 <u32> encrypted-password <password>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
password – MD5 encrypted password
- interfaces tunnel <id> ipv6 ospfv3 authentication md5 <u32> password <txt>
- SDE
M10-Smart
M2
RS420
AresC640
MD5 plain text password
- Values:
txt – MD5 plain text password (1-16)
- interfaces tunnel <id> ipv6 ospfv3 cost <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interface cost
- Values:
u32 – OSPFv3 cost (1-65535)
- interfaces tunnel <id> ipv6 ospfv3 dead-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interval after which neighbor is declared dead
- Values:
u32 – Neighbor dead interval in seconds (1-65535)
- interfaces tunnel <id> ipv6 ospfv3 hello-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interval between hello packets
- Values:
u32 – Interval between OSPFv3 hello packets in seconds (1-65535)
- interfaces tunnel <id> ipv6 ospfv3 ifmtu <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interface MTU
- Values:
u32 – Interface MTU value (1-65535)
- interfaces tunnel <id> ipv6 ospfv3 instance-id <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Instance identifier
- Values:
u32 – Instance ID (0-255)
- interfaces tunnel <id> ipv6 ospfv3 mtu-ignore
- SDE
M10-Smart
M2
RS420
AresC640
Disable Maximum Transmission Unit mismatch detection
- interfaces tunnel <id> ipv6 ospfv3 network <id>
- SDE
M10-Smart
M2
RS420
AresC640
Network type
- Values:
broadcast – Broadcast network type
point-to-point – Point-to-point network type
- interfaces tunnel <id> ipv6 ospfv3 passive
- SDE
M10-Smart
M2
RS420
AresC640
Disable forming of adjacency
- interfaces tunnel <id> ipv6 ospfv3 priority <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Router priority
- Values:
u32 – Priority (0-255)
- interfaces tunnel <id> ipv6 ospfv3 retransmit-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Interval between retransmitting lost link state advertisements
- Values:
u32 – Retransmit interval in seconds (3-65535)
- interfaces tunnel <id> ipv6 ospfv3 transmit-delay <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Link state transmit delay
- Values:
u32 – Link state transmit delay in seconds (1-65535)
- interfaces tunnel <id> ipv6 ripng
- SDE
M10-Smart
M2
RS420
AresC640
Routing Information Protocol (RIPng)
- interfaces tunnel <id> ipv6 ripng split-horizon
- SDE
M10-Smart
M2
RS420
AresC640
Split horizon parameters
- interfaces tunnel <id> ipv6 ripng split-horizon disable
- SDE
M10-Smart
M2
RS420
AresC640
Disable split horizon
- interfaces tunnel <id> ipv6 ripng split-horizon poison-reverse
- SDE
M10-Smart
M2
RS420
AresC640
Enable poison reverse for split-horizon
- interfaces tunnel <id> ipv6 router-advert
- SDE
M10-Smart
M2
RS420
AresC640
Configure parameters for sending Router Advertisements (RAs)
- interfaces tunnel <id> ipv6 router-advert cur-hop-limit <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Value to be placed in the Current Hop Limit field in RAs
- Values:
u32 – Value to place in the Current Hop Limit field in RAs (0-255)
- interfaces tunnel <id> ipv6 router-advert default-lifetime <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Value to be placed in Router Lifetime field in RAs
- Values:
u32 – Value in seconds to be placed in Router Lifetime field in RAs (4-9000)
u32 – This means “not a default router”, in Router Lifetime field (0)
- interfaces tunnel <id> ipv6 router-advert default-preference <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Default router preference
- Values:
low – Default router is low preference
medium – Default router is medium preference
high – Default router is high preference
- interfaces tunnel <id> ipv6 router-advert link-mtu <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Value of link MTU to place in RAs
- Values:
u32 – Do not send MTU options in RAs (0)
u32 – Value of link MTU to place in RAs (1280-2147483647)
- interfaces tunnel <id> ipv6 router-advert managed-flag <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Value for “managed address configuration” flag in RAs
- interfaces tunnel <id> ipv6 router-advert max-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Maximum interval between unsolicited multicast RAs
- Values:
u32 – Maximum interval in seconds between unsolicited multicast RAs (4-1800)
- interfaces tunnel <id> ipv6 router-advert min-interval <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Minimum interval between unsolicited multicast RAs
- Values:
u32 – Minimum interval in seconds between unsolicited multicast RAs (3-1350)
- interfaces tunnel <id> ipv6 router-advert name-server <ipv6>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
ipv6 – IPv6 address of a Recursive DNS Server
- Instances:
Multiple
- interfaces tunnel <id> ipv6 router-advert other-config-flag <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Value to be placed in the “other configuration” flag in RAs
- interfaces tunnel <id> ipv6 router-advert prefix <ipv6net>
- SDE
M10-Smart
M2
RS420
AresC640
IPv6 prefix to be advertised in Router Advertisements (RAs)
- Values:
ipv6net – IPv6 prefix to be advertized in Router Advertisements (RAs)
- Instances:
Multiple
- interfaces tunnel <id> ipv6 router-advert prefix <ipv6net> autonomous-flag <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Whether prefix can be used for address auto-configuration
- interfaces tunnel <id> ipv6 router-advert prefix <ipv6net> on-link-flag <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Flag that prefix can be used for on-link determination
- interfaces tunnel <id> ipv6 router-advert prefix <ipv6net> preferred-lifetime <u32|id>
- SDE
M10-Smart
M2
RS420
AresC640
Time in seconds that the prefix will remain preferred
- Values:
u32 – Time in seconds that the prefix will remain preferred (0-2147483647)
infinity – Prefix will remain preferred forever
- interfaces tunnel <id> ipv6 router-advert prefix <ipv6net> valid-lifetime <u32|id>
- SDE
M10-Smart
M2
RS420
AresC640
Time in seconds that the prefix will remain valid
- Values:
u32 – Time in seconds that the prefix will remain valid (0-2147483647)
infinity – Prefix will remain valid forever
- interfaces tunnel <id> ipv6 router-advert reachable-time <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Value to be placed in “Reachable Time” field in RAs
- Values:
u32 – Reachable Time value in RAs (in milliseconds) (1-3600000)
u32 – Reachable Time 0 (i.e., unspecified by this router) (0)
- interfaces tunnel <id> ipv6 router-advert retrans-timer <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Value to place in “Retrans Timer” field in RAs.
- Values:
u32 – Value in milliseconds to place in “Retrans Timer” field in RAs (0-2147483647)
- interfaces tunnel <id> ipv6 router-advert send-advert <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Enable/disable sending RAs
- interfaces tunnel <id> ipv6 router-advert used-prefixes
- SDE
M10-Smart
M2
RS420
AresC640
Delegate prefixes used on the interface
- interfaces tunnel <id> ipv6 router-advert used-prefixes autonomous-flag <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Whether prefix can be used for address auto-configuration
- interfaces tunnel <id> ipv6 router-advert used-prefixes on-link-flag <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Flag that prefix can be used for on-link determination
- interfaces tunnel <id> ipv6 router-advert used-prefixes preferred-lifetime <u32|id>
- SDE
M10-Smart
M2
RS420
AresC640
Time in seconds that the prefix will remain preferred
- Values:
u32 – Time in seconds that the prefix will remain preferred (0-2147483647)
infinity – Prefix will remain preferred forever
- interfaces tunnel <id> ipv6 router-advert used-prefixes valid-lifetime <u32|id>
- SDE
M10-Smart
M2
RS420
AresC640
Time in seconds that the prefix will remain valid
- Values:
u32 – Time in seconds that the prefix will remain valid (0-2147483647)
infinity – Prefix will remain valid forever
- interfaces tunnel <id> local-address <ipv4|ipv6>
- SDE
M10-Smart
M2
RS420
AresC640
Local IP address for this tunnel
- Values:
ipv4 – Local IPv4 address for this tunnel
ipv6 – Local IPv6 address for this tunnel [NOTICE: unavailable for mGRE tunnels]
- Local IP address:
- interfaces tunnel <id> local-interface <ifc>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
ifc – Bind interface for this tunnel
- interfaces tunnel <id> local-vrf <id>
- SDE
M10-Smart
M2
RS420
AresC640
Bind VRF for this tunnel
- Reference:
- interfaces tunnel <id> mtu <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Maximum Transmission Unit (MTU)
- Values:
u32 – Maximum Transmission Unit (MTU) (68-9000)
- interfaces tunnel <id> multicast
- SDE
M10-Smart
M2
RS420
AresC640
Enable multicast operation over tunnel
- interfaces tunnel <id> multipath
- SDE
M10-Smart
M2
RS420
AresC640
Multipath configuration
- interfaces tunnel <id> multipath traffic-steering
- SDE
M10-Smart
M2
RS420
AresC640
Traffic Steering configuration
- interfaces tunnel <id> multipath traffic-steering redirect
- SDE
M10-Smart
M2
RS420
AresC640
Enable Traffic Steering Redirect
- interfaces tunnel <id> multipath traffic-steering reverse
- SDE
M10-Smart
M2
RS420
AresC640
Enable Reverse Traffic Steering
- interfaces tunnel <id> nhrp
- SDE
M10-Smart
M2
RS420
AresC640
NHRP/GRE integration
- interfaces tunnel <id> nhrp extra-mark1 <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Set extra traffic mark 1 for NHRP packets
- Values:
u32 – Integer value from 0 to 2147483647 (0-2147483647)
- interfaces tunnel <id> nhrp extra-mark2 <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Set extra traffic mark 2 for NHRP packets
- Values:
u32 – Integer value from 0 to 2147483647 (0-2147483647)
- interfaces tunnel <id> nhrp holdtime <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Specify NBMA address validity time
- Values:
u32 – Time in seconds that NBMA addresses are advertised valid (1-65000)
- interfaces tunnel <id> nhrp ipsec <id>
- SDE
M10-Smart
M2
RS420
AresC640
Enable tunnel protection with DMVPN IPSec Profile
- Reference:
- interfaces tunnel <id> nhrp mark <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Set traffic mark for NHRP packets
- Values:
u32 – Mark value (0-2147483647)
- interfaces tunnel <id> nhrp nhs <ipv4>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
ipv4 – Nexthop Server configuration
- Instances:
Multiple
- Required:
- interfaces tunnel <id> nhrp nhs <ipv4> nbma <ipv4|fqdn>
- SDE
M10-Smart
M2
RS420
AresC640
NBMA address (external hub address or fqdn)
- Values:
ipv4 – IPv4 NBMA address
fqdn – Fully qualified domain name for NBMA address(es)
- interfaces tunnel <id> nhrp redirect
- SDE
M10-Smart
M2
RS420
AresC640
Send redirect notifications
- interfaces tunnel <id> nhrp resolve
- SDE
M10-Smart
M2
RS420
AresC640
Reply always resolution requests
- interfaces tunnel <id> nhrp shortcut
- SDE
M10-Smart
M2
RS420
AresC640
Allow shortcut establishment
- interfaces tunnel <id> nhrp transport-nat-support
- SDE
M10-Smart
M2
RS420
AresC640
Enable support for NAT in IPSec transport mode
- interfaces tunnel <id> nhrp vrf-mark <id>
- SDE
M10-Smart
M2
RS420
AresC640
VRF to mark NHRP packets
- Reference:
- interfaces tunnel <id> parameters
- SDE
M10-Smart
M2
RS420
AresC640
Tunnel parameters
- interfaces tunnel <id> parameters ip
- SDE
M10-Smart
M2
RS420
AresC640
IPv4 specific tunnel parameters
- interfaces tunnel <id> parameters ip key <u32>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
u32 – Tunnel key
- interfaces tunnel <id> parameters ip tos <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Type of Service (TOS)
- Values:
u32 – TOS value (0-99)
- interfaces tunnel <id> parameters ip ttl <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Time to live field
- Values:
u32 – Time to live value (0-255)
- interfaces tunnel <id> parameters ipv6
- SDE
M10-Smart
M2
RS420
AresC640
IPv6 specific tunnel parameters
- interfaces tunnel <id> parameters ipv6 encaplimit <u32|id>
- SDE
M10-Smart
M2
RS420
AresC640
Encaplimit field
- Values:
u32 – Encaplimit value (0-255)
none – Encaplimit disabled
- interfaces tunnel <id> parameters ipv6 flowlabel <id>
- SDE
M10-Smart
M2
RS420
AresC640
Flowlabel
- Values:
0-0xfffff – Hexadecimal flowlabel
inherit – Inherit flowlabel
- interfaces tunnel <id> parameters ipv6 hoplimit <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Hoplimit
- Values:
u32 – Hoplimit value (0-255)
- interfaces tunnel <id> parameters ipv6 tclass <int|id>
- SDE
M10-Smart
M2
RS420
AresC640
Traffic class (Tclass)
- Values:
int – Traffic class value (0-0xff)
inherit – Inherit value
- interfaces tunnel <id> ppp-interface <ifc>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
ifc – PPP interface that supplies the local IP address for this tunnel
- interfaces tunnel <id> remote-ip <ipv4|ipv6>
- SDE
M10-Smart
M2
RS420
AresC640
Remote IP address for this tunnel
- Values:
ipv4 – Remote IPv4 address
ipv6 – Remote IPv6 address
- interfaces tunnel <id> tcp-mss <u32>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
u32 – Change tcp-mss value
- interfaces tunnel <id> traffic
- SDE
M10-Smart
M2
RS420
AresC640
Traffic processing options
- interfaces tunnel <id> traffic control
- SDE
M10-Smart
M2
RS420
AresC640
Traffic control for interface
- interfaces tunnel <id> traffic control in <id>
- SDE
M10-Smart
M2
RS420
AresC640
Ingress traffic control for interface
- Reference:
- interfaces tunnel <id> traffic control out <id>
- SDE
M10-Smart
M2
RS420
AresC640
Egress traffic control for interface
- Reference:
- interfaces tunnel <id> traffic nat
- SDE
M10-Smart
M2
RS420
AresC640
Network Address Translation (NAT) parameters
- interfaces tunnel <id> traffic nat destination
- SDE
M10-Smart
M2
RS420
AresC640
Destination NAT settings
- interfaces tunnel <id> traffic nat destination rule <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Rule number for NAT
- Values:
u32 – Number for this NAT rule (1-9999)
- Instances:
Multiple
- interfaces tunnel <id> traffic nat destination rule <u32> address <ipv4|ipv4net|ipv4range|id>
- SDE
M10-Smart
M2
RS420
AresC640
IP address, subnet, range or redirect
- Values:
ipv4 – NAT to the specified IP address
ipv4net – NAT to the specified network address
ipv4range – NAT to the specified IP range
redirect – NAT to the interface address
- interfaces tunnel <id> traffic nat destination rule <u32> description <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Rule description
- interfaces tunnel <id> traffic nat destination rule <u32> log
- SDE
M10-Smart
M2
RS420
AresC640
Log packets to which this rule has been applied
- interfaces tunnel <id> traffic nat destination rule <u32> log level <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Loggin level
- Values:
emerg – Emergency messages
alert – Urgent messages
crit – Critical messages
err – Error messages
warn – Warning messages
notice – Messages for further investigation
info – Informational messages
debug – Debug messages
- interfaces tunnel <id> traffic nat destination rule <u32> log prefix <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Log message prefix text, up to 29 characters
- interfaces tunnel <id> traffic nat destination rule <u32> network <ipv4net>
- SDE
M10-Smart
M2
RS420
AresC640
IP prefix to use in translation (host part is kept)
- Values:
ipv4net – NAT to the specified network address, host part of the address will remain unchanged
- interfaces tunnel <id> traffic nat destination rule <u32> port <u32|id>
- SDE
M10-Smart
M2
RS420
AresC640
NAT port
- Values:
u32 – Port to use in PAT (1-65535)
range – Port range (pool, for example, 1001-1005)
- interfaces tunnel <id> traffic nat destination rule <u32> protocol <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – NAT transport protocol
- interfaces tunnel <id> traffic nat destination rule <u32> selector <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Traffic selector
- Reference:
- interfaces tunnel <id> traffic nat source
- SDE
M10-Smart
M2
RS420
AresC640
Source NAT settings
- interfaces tunnel <id> traffic nat source rule <u32>
- SDE
M10-Smart
M2
RS420
AresC640
Rule number for NAT
- Values:
u32 – Number for this NAT rule (1-9999)
- Instances:
Multiple
- interfaces tunnel <id> traffic nat source rule <u32> address <ipv4|ipv4net|ipv4range|id>
- SDE
M10-Smart
M2
RS420
AresC640
IP address, subnet, range or masquerade
- Values:
ipv4 – NAT to the specified IP address
ipv4net – NAT to the specified network address
ipv4range – NAT to the specified IP range
masquerade – NAT to the interface address
- interfaces tunnel <id> traffic nat source rule <u32> description <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Rule description
- interfaces tunnel <id> traffic nat source rule <u32> log
- SDE
M10-Smart
M2
RS420
AresC640
Log packets to which this rule has been applied
- interfaces tunnel <id> traffic nat source rule <u32> log level <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Loggin level
- Values:
emerg – Emergency messages
alert – Urgent messages
crit – Critical messages
err – Error messages
warn – Warning messages
notice – Messages for further investigation
info – Informational messages
debug – Debug messages
- interfaces tunnel <id> traffic nat source rule <u32> log prefix <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – Log message prefix text, up to 29 characters
- interfaces tunnel <id> traffic nat source rule <u32> network <ipv4net>
- SDE
M10-Smart
M2
RS420
AresC640
IP prefix to use in translation (host part is kept)
- Values:
ipv4net – NAT to the specified network address, host part of the address will remain unchanged
- interfaces tunnel <id> traffic nat source rule <u32> port <u32|id>
- SDE
M10-Smart
M2
RS420
AresC640
NAT port
- Values:
u32 – Port to use in PAT (1-65535)
range – Port range (pool, for example, 1001-1005)
- interfaces tunnel <id> traffic nat source rule <u32> protocol <txt>
- SDE
M10-Smart
M2
RS420
AresC640
- Values:
txt – NAT transport protocol
- interfaces tunnel <id> traffic nat source rule <u32> selector <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Traffic selector
- Reference:
- interfaces tunnel <id> traffic policy
- SDE
M10-Smart
M2
RS420
AresC640
Traffic policy rulesets for interface
- interfaces tunnel <id> traffic policy in <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Input traffic policy ruleset for interface
- Reference:
- Instances:
Multiple
- interfaces tunnel <id> traffic policy in <txt> priority <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Priority order for traffic policy
- Values:
very-high – First policy executed before NAT
high – Second policy executed before NAT
low – First policy executed after NAT
very-low – Second policy executed after NAT
- interfaces tunnel <id> traffic policy local-in <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Local input traffic policy ruleset for interface
- Reference:
- Instances:
Multiple
- interfaces tunnel <id> traffic policy local-in <txt> priority <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Priority order for traffic policy
- Values:
very-high – First policy executed
high – Second policy executed
low – Third policy executed
very-low – Fourth policy executed
- interfaces tunnel <id> traffic policy local-out <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Local output traffic policy ruleset for interface
- Reference:
- Instances:
Multiple
- interfaces tunnel <id> traffic policy local-out <txt> priority <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Priority order for traffic policy
- Values:
very-high – First policy executed
high – Second policy executed
low – Third policy executed
very-low – Fourth policy executed
- interfaces tunnel <id> traffic policy out <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Output traffic policy ruleset for interface
- Reference:
- Instances:
Multiple
- interfaces tunnel <id> traffic policy out <txt> priority <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Priority order for traffic policy
- Values:
very-high – First policy executed before NAT
high – Second policy executed before NAT
low – First policy executed after NAT
very-low – Second policy executed after NAT
- interfaces tunnel <id> traffic zone <txt>
- SDE
M10-Smart
M2
RS420
AresC640
Traffic zone associated with this interface
- Reference:
- interfaces tunnel <id> vrf <id>
- SDE
M10-Smart
M2
RS420
AresC640
Virtual Routing and Forwarding domain name
- Reference: