Speed 1000Mbps
This scenario tests ethernet interface default speed verification at 1000Mbps. DUT0 and DUT1 ethernet interfaces are configured with standard settings, then the default 1000Mbps speed is verified to ensure interfaces are running at expected gigabit speeds with connectivity validation.
Test Ethernet Speed 1000Mbps Default Verification
Description
Configure DUT0 and DUT1 ethernet interfaces with standard settings.
Wait for connectivity between both devices to be established, then verify
that DUT0 interface is running at default 1000Mbps speed with full duplex
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces ethernet eth0 address 192.168.100.10/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.20/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 local-address 192.168.100.10 count 1 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) from 192.168.100.10 : 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.729 ms --- 192.168.100.20 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.729/0.729/0.729/0.000 ms
Step 4: Run command interfaces ethernet eth0 show physical at DUT0 and check if output contains the following tokens:
Speed: 1000Mb/sShow output
Settings for eth0: Supported ports: [ ] Supported link modes: 10baseT/Full 100baseT/Full 1000baseT/Full 2500baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Full 100baseT/Full 1000baseT/Full 2500baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: on master-slave cfg: preferred slave master-slave status: slave Port: Twisted Pair PHYAD: 1 Transceiver: external MDI-X: on (auto) Supports Wake-on: d Wake-on: d Current message level: 0x00007fff (32767) drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol Link detected: yes driver: fsl_dpa version: 6.12.20 firmware-version: 0 expansion-rom-version: bus-info: soc:fsl,dpaa supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no
Step 5: Run command interfaces ethernet eth0 show physical at DUT0 and check if output contains the following tokens:
Duplex: FullShow output
Settings for eth0: Supported ports: [ ] Supported link modes: 10baseT/Full 100baseT/Full 1000baseT/Full 2500baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Full 100baseT/Full 1000baseT/Full 2500baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: on master-slave cfg: preferred slave master-slave status: slave Port: Twisted Pair PHYAD: 1 Transceiver: external MDI-X: on (auto) Supports Wake-on: d Wake-on: d Current message level: 0x00007fff (32767) drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol Link detected: yes driver: fsl_dpa version: 6.12.20 firmware-version: 0 expansion-rom-version: bus-info: soc:fsl,dpaa supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no