Speed 100Mbps
This scenario tests ethernet interface speed configuration to 100Mbps. DUT0 ethernet interface speed is changed to 100Mbps with full duplex, then connectivity is verified between DUT0 and DUT1 to ensure the speed change doesn’t affect basic network functionality.
Test Ethernet Speed 100Mbps Configuration
Description
Configure DUT0 ethernet interface to 100Mbps speed and verify
the speed change is applied correctly. Then test connectivity
between DUT0 and DUT1 to ensure network functionality.
Scenario
Step 1: Set the following configuration in DUT0 :
set interfaces ethernet eth1 address 192.168.100.10/24 set interfaces ethernet eth1 link-mode force speed 100 duplex full set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 2: Set the following configuration in DUT1 :
set interfaces ethernet eth0 address 192.168.100.20/24 set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'
Step 3: Run command interfaces ethernet eth1 show physical at DUT0 and check if output contains the following tokens:
Speed: 100Mb/sShow output
Settings for eth1: Supported ports: [ TP MII FIBRE ] Supported link modes: 10baseT/Full 100baseT/Full 1000baseT/Full 1000baseX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Full 100baseT/Full 1000baseT/Full 1000baseX/Full Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Auto-negotiation: off Port: Twisted Pair PHYAD: 7 Transceiver: external MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00007fff (32767) drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol Link detected: no driver: fsl_dpa version: 6.12.20 firmware-version: 0 expansion-rom-version: bus-info: soc:fsl,dpaa supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no
Step 4: Run command interfaces ethernet eth1 show physical at DUT0 and check if output contains the following tokens:
Duplex: FullShow output
Settings for eth1: Supported ports: [ TP MII FIBRE ] Supported link modes: 10baseT/Full 100baseT/Full 1000baseT/Full 1000baseX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Full 100baseT/Full 1000baseT/Full 1000baseX/Full Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Auto-negotiation: off Port: Twisted Pair PHYAD: 7 Transceiver: external MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00007fff (32767) drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol Link detected: no driver: fsl_dpa version: 6.12.20 firmware-version: 0 expansion-rom-version: bus-info: soc:fsl,dpaa supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no
Step 5: Ping IP address 192.168.100.20 from DUT0:
admin@DUT0$ ping 192.168.100.20 local-address 192.168.100.10 count 1 size 56 timeout 1Show output
PING 192.168.100.20 (192.168.100.20) from 192.168.100.10 : 56(84) bytes of data. 64 bytes from 192.168.100.20: icmp_seq=1 ttl=64 time=0.583 ms --- 192.168.100.20 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.583/0.583/0.583/0.000 ms