Shutdown

Scenario to verify BGP peer-group shutdown inheritance. When shutdown is configured on a peer-group, all neighbor sessions that are members of the group are administratively disabled.

Test iBGP - Peer-group shutdown disables session

Description

Test that shutdown configured on a peer-group administratively disables all member sessions. First the session establishes normally, then shutdown is applied to the peer-group causing the session to enter Idle (Admin) state.

Scenario

Step 1: Set the following configuration in DUT0 :

set interfaces ethernet eth0 address 10.10.0.100/24
set protocols bgp 20 neighbor peer peer-group MYGROUP
set protocols bgp 20 neighbor peer remote-address 10.10.0.200
set protocols bgp 20 neighbor peer remote-as 20
set protocols bgp 20 peer-group MYGROUP remote-as 20
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Step 2: Set the following configuration in DUT1 :

set interfaces ethernet eth0 address 10.10.0.200/24
set protocols bgp 20 neighbor peer remote-address 10.10.0.100
set protocols bgp 20 neighbor peer remote-as 20
set protocols bgp 20 redistribute connected
set system login user admin authentication encrypted-password '$6$GSjsCj8gHLv$/VcqU6FLi6CT2Oxn0MJQ2C2tqnRDrYKNF8HIYWJp68nvXvPdFccDsT04.WtigUONbKYrgKg8d6rEs8PjljMkH0'

Attention

Verify iBGP session establishes and route is received.

Step 3: Run command protocols bgp show ip summary at DUT0 and check if output matches the following regular expressions:

10.10.0.200.*Established
Show output
IPv4 Unicast Summary:
BGP router identifier 10.10.0.100, local AS number 20 VRF default vrf-id 0
BGP table version 1
RIB entries 1, using 128 bytes of memory
Peers 1, using 24 KiB of memory
Peer groups 1, using 64 bytes of memory

Neighbor        LocalAddr       V         AS   MsgRcvd   MsgSent   TblVer  InQ OutQ  Up/Down        State   PfxRcd   PfxSnt Desc
10.10.0.200     10.10.0.100     4         20         4         4        1    0    0 00:00:01  Established        1        0 FRRouting/10.4.1

Total number of neighbors 1

Step 4: Run command protocols bgp show ip at DUT0 and check if output matches the following regular expressions:

10.10.0.0/24
Show output
BGP table version is 1, local router ID is 10.10.0.100, vrf id 0
Default local pref 100, local AS 20
local address -
Status codes:  s suppressed, d damped, h history, u unsorted, * valid, > best, = multipath,
               i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes:  i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found

     Network          Next Hop            Metric LocPrf Weight Path
 *ui 10.10.0.0/24     10.10.0.200              0    100      0 ?

Displayed 1 routes and 1 total paths

Note

Apply shutdown to the peer-group to disable all member sessions.

Step 5: Modify the following configuration lines in DUT0 :

set protocols bgp 20 peer-group MYGROUP shutdown

Attention

Verify session enters Idle (Admin) after peer-group shutdown.

Step 6: Run command protocols bgp show ip summary at DUT0 and check if output matches the following regular expressions:

10.10.0.200.*Idle \(Admin\)
Show output
IPv4 Unicast Summary:
BGP router identifier 10.10.0.100, local AS number 20 VRF default vrf-id 0
BGP table version 2
RIB entries 0, using 0 bytes of memory
Peers 1, using 24 KiB of memory
Peer groups 1, using 64 bytes of memory

Neighbor        LocalAddr       V         AS   MsgRcvd   MsgSent   TblVer  InQ OutQ  Up/Down        State   PfxRcd   PfxSnt Desc
10.10.0.200     10.10.0.100     4         20         4         5        0    0    0 00:00:00 Idle (Admin)        0        0 FRRouting/10.4.1

Total number of neighbors 1